PowerWalker VI RT HID Series Manuale utente

ENGLISH

Assembly of VI/VFI RT HID Series

I. Installing the UPS

ENGLISH

II. Connecting the EBM in Tower form:

1. Slide down the UPS and EBM vertically and place two UPS stands with the extend

part at the end of the tower.

2. Tighten the screw on the metal

sheet for stabilization

3. Connect the Earth line from UPS

(port A ) to EBM (port B)

4. Take off the front panel, and connect the battery terminal (A) from UPS to EBM

terminal (B) shown as below. Users need to remove the small gate(C) on side of

the front panel to allow the outlet wire of the EBM to pass through the gate and

then reassemble front panel.

ENGLISH

III. Connecting the EBM in a rack form

1. Using the same method as assembling

UPS in a rack form, assemble EBM into

the rack-mounting on the top or

bottom of the UPS.

2. Connect the earth line from UPS (port

A ) to EBM (port B )

3. Take off the LCD box, and unscrew the

internal screws.

4. Take off the front panel, and connect

the battery terminal (A) from UPS to

EBM terminal (B) shown as below.

Users need to remove the small gate(C)

on side of the front panel to allow the

outlet wire of the EBM to pass through

the gate and then reassemble front

panel.

5. After installing the UPS into rack, the load can then be connected to UPS. Please

Unscrew

ENGLISH

make sure the load equipment is turned off before plugging all loads into the output

receptacle.

IV. Connecting the Multiple EBMs

1000VA/1500VA/2000VA and 3000VA UPS include external battery port that allows users

to connect multiple EBM in order to provide additional backup time. Follow the

procedure to install multiple EBM as below.

V. Connecting multiple EBMs in Tower form

1. Connect Earth line between UPS and the

first EBM, and then connect Earth Line

between the first EBM and the second

EBM.

2. Take off the front panel, and connect the

battery terminal (A) from UPS to EBM

terminal (B) shown as below. And then

connect the battery terminal (D) from the

first EBM to the battery terminal (E) from

the second EBM. Users need to remove

the small gate(C) on side of the front

panel to allow the outlet wire of the EBM

to pass through the gate and then

reassemble front panel.

VI. Connecting the Multiple EBMs in rack form

1. Connect Earth line between UPS and the first EBM, and then connect Earth Line between

the first EBM and the second EBM.

ENGLISH

2. Take off the front panel, and connect the battery terminal (A) from UPS to EBM terminal

(B) shown as below. And then connect the battery terminal (D) from the first EBM to the

battery terminal (E) from the second EBM. Users need to remove the small gate(C) on side

of the front panel to allow the outlet wire of the EBM to pass through the gate and then

reassemble front panel.

Note: Three or more EBMs can be connected to the UPS in the same way as shown above.

VII. Replacing UPS Internal Batteries

Follow the steps and Charts as below to replace batteries:

1. Take off the LCD box, and remove the

screws.

2. Slide and Pull the front panel leftward

and then take it off.

ENGLISH

3. Disconnect the cable from the UPS and

battery pack.

4. Remove the right inner battery bracket.

5. Pull the battery pack out onto flat area.

6. Install new battery pack into UPS.

7. Screw up the battery bracket and

reconnect the battery cable A and B

8. Re-install the front panel back to UPS.

Questo manuale è adatto per i seguenti modelli

Altri manuali PowerWalker UPS

PowerWalker

PowerWalker VFD 400 Manuale utente

PowerWalker

PowerWalker VFI 1000RM Manuale utente

PowerWalker

PowerWalker VI 650 SH Manuale utente

PowerWalker

PowerWalker DC UPS Manuale utente

PowerWalker

PowerWalker VFI 1000 CRS Manuale utente

PowerWalker

PowerWalker VFI 10K-80K CPG 3 Manuale utente

PowerWalker

PowerWalker VFI 1000T/E LCD Manuale utente

PowerWalker

PowerWalker 1000VA Manuale utente

PowerWalker

PowerWalker VFI 2000RT Manuale utente

PowerWalker

PowerWalker VI 1200 RLE Manuale utente

PowerWalker

PowerWalker VFI 3/3 Series Manuale utente

PowerWalker

PowerWalker VFI 1000 AT Manuale utente

PowerWalker

PowerWalker VI 3000RT LCD Manuale utente

PowerWalker

PowerWalker VFI 160K CPG 3/3 BX Manuale utente

PowerWalker

PowerWalker VI 400 SE Manuale utente

PowerWalker

PowerWalker VFI 1000 RMG PF1 Manuale utente

PowerWalker

PowerWalker VFI 10K CPH Manuale utente

PowerWalker

PowerWalker BP P96T Guida per l'amministratore

PowerWalker

PowerWalker VFI 1000-3000 CG PF1 Manuale utente

PowerWalker

PowerWalker VI 2000 LCD Manuale utente

PowerWalker

PowerWalker VFI 6000 ICT Manuale utente

PowerWalker

PowerWalker VFI 10K ICT IoT 3/3 BI Manuale utente

PowerWalker

PowerWalker VFI 3000T LCD Manuale utente

PowerWalker

PowerWalker VFD 400 Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente