PRECISION DIGITAL Pd663 Manuale utente

PRECISION DIGITAL CORPORATION

89 October Hill Road • Holliston MA 01746 USA

Tel (800) 343-1001 • Fax (508) 655-8990

www.predig.com

PD663 EXPLOSION-PROOF

LOOP-POWERED METER

4-20 mA input

3½+ Digits LCD, 0.6" High

Easy Four-Button Programming

Programmable Noise Filter

Max/Min Display

HART®Protocol Transparent

Loop-Powered Backlight Option

1.7 V drop (4.7 V with Backlight)

NEMA 4X Enclosure

Operates from -40 to 75°C

PD663 Loop-Powered Meter Instruction Manual

Disclaimer

The information contained in this document is subject to change without notice.

Precision Digital makes no representations or warranties with respect to the

contents hereof; and specifically disclaims any implied warranties of

merchantability or fitness for a particular purpose.

CAUTION: Read complete

instructions prior to installation and

operation of the meter.

WARNING: Risk of

electric shock or

personal injury.

WARNINGS

• This product is not recommended for life support applications or applications

where malfunctioning could result in personal injury or property loss. Anyone

using this product for such applications does so at his/her own risk. Precision

Digital Corporation shall not be held liable for damages resulting from such

improper use.

• Failure to follow installation guidelines could result in death or serious injury.

Make sure only qualified personnel perform the installation.

• Never remove the meter cover in explosive environments when the circuit is

live.

• Cover must be fully engaged to meet flameproof/explosion-proof

requirements.

PD663 Loop-Powered Meter Instruction Manual

Limited Warranty

Precision Digital Corporation warrants this product against defects in material or

workmanship for the specified period under “Specifications” from the date of

shipment from the factory. Precision Digital’s liability under this limited warranty

shall not exceed the purchase value, repair, or replacement of the defective unit.

Registered Trademarks

All trademarks mentioned in this document are the property of their respective

owners.

www.predig.com

PD663 Loop-Powered Meter Instruction Manual

INTRODUCTION

The ProtEX-Lite PD663 is a rugged, NEMA 4X loop-powered meter in an

explosion-proof enclosure ideal for applications where a simple, inexpensive

display is required in a hazardous area. The PD663 is scaled using four push

buttons and can be done without applying an actual calibration signal.

Programming may also be done through the explosion-proof enclosure with

optional magnetic reed switches and a magnet key. The PD663’s display will

read up to 2999; we call this 3½+ digits! The loop-powered backlighting option

lets you see the display under any lighting condition and is powered completely

from the 4-20 mA loop. This means there is no need for additional wiring and

never any batteries to change.

The PD663 is housed in a rugged, explosion-proof, cast aluminum, NEMA 4X

enclosure and is provided with two threaded conduit holes and integrated pipe or

wall mounting holes.

ORDERING INFORMATION

Model Options Installed

PD663-0L0-00 None

PD663-0K0-00 Loop-Powered Backlight

PD663-0LA-00 Reed Switch

PD663-0KA-00 Loop-Powered Backlight and Reed Switch

Accessories

Model Description

PDA6845 2" Pipe Mounting Kit

PDA-MAG Magnet Assembly for Reed Switches

PDA0003 ½" M-NPT to ¾" F-NPT Adapter

PD663 Loop-Powered Meter Instruction Manual

Table of Contents

INTRODUCTION-----------------------------------------------------------------------4

ORDERING INFORMATION -------------------------------------------------------4

SPECIFICATIONS --------------------------------------------------------------------7

General -------------------------------------------------------------------------------------------7

Input -----------------------------------------------------------------------------------------------8

Product Ratings and Approvals----------------------------------------------------------9

Electromagnetic Compatibility --------------------------------------------------------- 10

SAFETY INFORMATION---------------------------------------------------------- 11

INSTALLATION---------------------------------------------------------------------- 12

Unpacking ------------------------------------------------------------------------------------- 12

Pre-Installed Conduit Plug --------------------------------------------------------------- 12

Mounting --------------------------------------------------------------------------------------- 13

Cover Jam Screw---------------------------------------------------------------------------- 13

Connections ---------------------------------------------------------------------------------- 13

4-20 mA Input Connections & Wiring Diagrams........................................ 15

SETUP AND PROGRAMMING-------------------------------------------------- 16

Buttons and Display ----------------------------------------------------------------------- 17

Main Menu Display Functions & Messages ---------------------------------------- 18

Main Menu ------------------------------------------------------------------------------------- 19

Setting Numeric Values ------------------------------------------------------------------- 19

Setting Up the Meter ----------------------------------------------------------------------- 20

Programming the Meter............................................................................. 20

Setting the Decimal Point (dP)................................................................... 21

Scaling the Meter (SCL) ............................................................................. 21

Calibrating the Meter (Cal)........................................................................ 22

Re-calibrating the Internal Calibration Reference (ICal) .......................... 22

Advanced Features Menu ---------------------------------------------------------------- 23

Advanced Features Menu & Display Messages........................................ 24

Information Menu (info) ............................................................................. 25

Input Signal Filter (FIL) ............................................................................. 25

Internal Calibration (ICal) ......................................................................... 26

OPERATION-------------------------------------------------------------------------- 27

Front Panel Buttons Operation--------------------------------------------------------- 27

Maximum & Minimum Readings (HI & LO) ----------------------------------------- 28

Reset Meter to Factory Defaults ------------------------------------------------------- 29

Factory Defaults & User Settings------------------------------------------------------ 30

TROUBLESHOOTING ------------------------------------------------------------- 31

Troubleshooting Tips ---------------------------------------------------------------------- 31

MOUNTING DIMENSIONS ------------------------------------------------------- 32

PD663 Loop-Powered Meter Instruction Manual

QUICK USER INTERFACE REFERENCE ----------------------------------- 34

EC DECLARATION OF CONFORMITY--------------------------------------- 35

Table of Figures

Figure 1. PD663 Meter Assembly, Rear View ...................................14

Figure 2. PD663 Input Connections without Backlight ................... 15

Figure 3. PD663 Input Connections with Backlight.........................15

Figure 4. Enclosure Dimensions – Front View.................................32

Figure 5. Enclosure Dimensions – Side Cross Section View ......... 33

PD663 Loop-Powered Meter Instruction Manual

SPECIFICATIONS

Except where noted all specifications apply to operation at +25°C.

General

DISPLAY 0.6" (15.24 mm) LCD, 3½+ digits; -1999 to 2999

DISPLAY

UPDATE RATE

2 Updates/Second

OVERRANGE Display flashes 2999

UNDERRANGE Display flashes -1999

PROGRAMMING

METHOD

Four internal pushbuttons, optional magnetic reed

switches.

NOISE FILTER Programmable HI, LO, or OFF

RECALIBRATION Recalibration is recommended at least every 12 months.

MAX/MIN

DISPLAY

Max/Min readings reached by the process are stored until

reset by the user or until power to the meter is turned off.

NON-VOLATILE

MEMORY

All programmed settings are stored in non-volatile memory

for a minimum of ten years if power is lost.

NORMAL MODE

REJECTION

64 dB at 50/60 Hz

ENVIRONMENTAL Operating temperature range: -40 to 75°C

Storage temperature range: -40 to 75°C

Relative humidity: 0 to 90% non-condensing

CONNECTIONS Removable screw terminals accept 12 to 22 AWG wire

ENCLOSURE Explosion-proof die cast aluminum with glass window,

0.30% max copper content, corrosion resistant epoxy

coating, color: blue. NEMA 4X, 7, & 9, IP68.

Two ½” NPT threaded conduit openings. One ½” NPT

nickel plated brass conduit plug with 10 mm hex key fitting

installed.

MOUNTING May be mounted directly to conduit. Two mounting holes

for 1.5” pipe or wall mounting. See Mounting Dimensions

on page 32.

TIGHTENING

TORQUE

Screw terminal electrical connectors: 4.5 lb-in (0.5 Nm)

OVERALL

DIMENSIONS

4.84" x 4.29" x 3.62" (123 mm x 109 mm x 92 mm)

(W x H x D)

WEIGHT 2.45 lbs (40 oz, 1.13 kg)

PD663 Loop-Powered Meter Instruction Manual

WARRANTY 3 years parts and labor

Input

ACCURACY ±1 count

TEMPERATURE

DRIFT

50 PPM/C from -40 to 75C ambient

DECIMAL POINT User selectable decimal point

MINIMUM SPAN Input 1 & Input 2: 0.40 mA

CALIBRATION

RANGE

An Error message will appear if input 1 and input 2 signals

are too close together.

Input

Range

Minimum Span

Input 1 & Input 2

4-20 mA 0.40 mA

MAXIMUM

VOLTAGE DROP

Without Backlight With Backlight

1.7 VDC @ 20 mA 4.7 VDC @ 20 mA

EQUIVALENT

RESISTANCE

85 Ω@ 20 mA 185 Ω@ 20 mA

LOOP-POWERED

BACKLIGHT

OPTION

Factory installed only. Powered directly from the 4-20 mA

loop, no batteries required. Backlight can be enabled or

disabled via alternative wiring of terminal block. The

display brightness will increase as the input signal current

increases.

INPUT

OVERLOAD

Over current protection to 2 A max.

PD663 Loop-Powered Meter Instruction Manual

Product Ratings and Approvals

FM Class I, Division 1, Groups B, C, D

Class II, Division 1, Groups E, F, G

Class III, Division 1; T6

Class I, Zone 1, AEx d IIC T6 Gb

Zone 21, AEx tb IIIC T85°C

Ta = -40°C to +75°C

Enclosure: Type 4X & IP66

Certificate number: 3040391

ATEX II 2 G D

Ex d IIC T6 Gb

Ex tb IIIC T85°C Db IP68

Ta = -40°C to +75°C

ATEX Certificate: Sira 10ATEX1116X

CSA Class I, Division 1, Groups B, C, D

Class II, Division 1, Groups E, F, G

Class III, Division 1; T6

Class I, Zone 1, Ex d IIC T6

Ta = -40°C to +75°C

Enclosure: Type 4X & IP66

Certificate number: 11 2325749

IECEx IECEx SIR 10.0056X

Ex d IIC T6 Gb

Ex tb IIIC T85°C Db IP68

Ta = -40°C to +75°C

Special Conditions for Safe Use:

Use suitably certified and dimensioned cable entry device and/or plug. The

equipment shall be installed such that the supply cable is protected from

mechanical damage. The cable shall not be subjected to tension or torque. If the

cable is to be terminated within an explosive atmosphere, then appropriate

protection of the free end of the cable shall be provided.

Year of Construction

This information is contained within the serial number with the first four digits

representing the year and month in the YYMM format.

For European Community: The PD663 must be installed in accordance with the

ATEX directive 94/9/EC and the product certificate Sira 10ATEX116X.

PD663 Loop-Powered Meter Instruction Manual

Electromagnetic Compatibility

EMISSIONS EN 61326:2006

Safety requirements for measurement, control, and

laboratory use – Industrial

Group 1 Class A ISM emissions requirements

Radiated

Emissions

Class A

IMMUNITY EN 61326:2006

Safety requirements for measurement, control, and

laboratory use

ESD ±4 kV contact,

±8 kV air

RFI – Amplitude

Modulated

80-1000 MHz @ 10 V/m,

1.4-2.0 GHz @ 3 V/m,

2.0-2.7 GHz @ 1 V/m,

80% AM (1 kHz)

EFT ±2 kV DC mains, ±1 kV other

Telco Surge ±1 kV

CRFI 3 V, 0.15-80 MHz, 1 kHz 80% AM

Altri manuali per pd663

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PRECISION DIGITAL Strumento di misura

PRECISION DIGITAL

PRECISION DIGITAL Sabre Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProVu PD7000 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProVu Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProtEx Pro PD6800-0L1 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD6720 Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProtEX-MAX PD8-7000 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProVu Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Loop Leader PD689 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProtEX-MAX PD8-6060 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6200 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6060 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6200 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-6400 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL ProtEX-MAX PD8-6001 Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD6800 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD8-7000 Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Helios PD2-7000 Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD603 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD685 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Sabre Series Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL Sabre P PD603 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL PD213 Manuale utente

PRECISION DIGITAL

PRECISION DIGITAL pd663 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente