Pro-Ject Audio Systems Measure it E Manuale utente

Thank you for purchasing a Pro-Ject Audio Systems stylus balance.

Warning of a hazard for the user, the unit or possible misuse

Important notice

What is in the box

•stylus balance

•calibration weight (5 g)

•2 LR43 (AG12) button cell batteries plus 2 pieces as backup

•protection pouch for the meter

•user guide

Calibration

1 Make sure the surface is level.

2Turn on the meter with the ON/OFF button. The display will show 0.000 after a few seconds.

Give your stylus balance sufficient warm up time. Usually 30 seconds give the internal

components time to stabilise before calibrating.

3Press and hold the MODE button until the display shows CAL and then press the MODE button

again, the display will show 5.000 (flashing) after CAL (flashing).

4Gently place the 5g weight on the centre of the platform. After approximately 5 seconds the

display will read 5.000, PASS and 5.000.

Occasionally the display will show for example 5.002 or 5.004 instead of 5.000. This is

no defect. It will not affect the calibration.

5Remove the weight and press ON/OFF to turn off the meter.

Choosing the weighting mode

The meter has to be turned on. The display shows 0.000. Pressing the MODE switches between the

different weighting modes.

Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct).

Cartridge downforce adjustment - weighting mode gram

1 Make sure the surface you use the turntable on is level.

2Remove the stylus guard and the stylus balance protection cover. Gently place the meter on the

platter. Move the headshell over the weighting platform and place the tip of the needle above the

black dot of the weighting platform.

3Turn on the stylus balance with the ON/OFF button. The display will show 0.000 after a few

seconds. Give your meter sufficient warm up time. Usually 30 seconds to give the internal

components time to stabilise.

4Gently lower the tonearm until the stylus is on the black dot of the weighting platform. The display

shows the tracking force.

5Lift the tonearm and adjust the counter weight (tracking weight dial) and repeat the above

procedure until the recommended tracking force is achieved.

Never load the stylus balance with more than 5g, overloading can permanently damage it.

Backlight

Turn on the stylus balance and the backlight will automatically switch on (no further key switch

needed). When the stylus balance is switched off, the backlight will switch off.

Other display readouts

No display, backlight getting weak - batteries are empty and need to be replaced.

o_LD - overload (more than 5g). Please remove the excessive load immediately.

LLLLL - The weighting load cell has been damaged by misuse (i.e. it was shocked, dropped or

overloaded). You can try to recalibrate the meter. If the load cell has not been damaged to

much, it will work again after recalibration.

UNSt - Use the meter on a more stable, vibration free surface.

Changing batteries

Proceed as follows:

•Take off both battery case covers

•Replace both batteries together. Make sure the batteries are the right way round

•Refit the battery case covers

Battery type: 2 x LR45 (AG12) button cells, 1,5V

If the stylus balance is not used over a long period of time the batteries should be removed.

Do not dispose the batteries as ordinary domestic refuse. Please d

ispose your exhausted

batteries at the appropriate collection sites -

usually located at supermarkets and

drugstores.

Technical specifications Measure it E

Capacity 0 - 5g

Variance ±0,002g

Weighting modes gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct)

Display 4 digit LCD with backlight

Calibration auto calibration using a 5g weight

Auto off 30 seconds off

Replacement battery 2 x LR43 (AG12) button cells, 1,5V

Operating temperature +10 - +30°C (50 - 86 degrees Fahrenheit)

Dimensions (W x H x D) 96 x 21 x 43mm

Weight 49g

Warranty

The manufacturer accepts no responsibility for damage caused by not adhering to these

instructions for use. Modification or change to any part of the product by unauthorized

persons, will release the manufacturer from any liability over and above the lawful rights of

the customer.

Pro-Ject Audio Systems is a Registered Trademark of

H. Lichtenegger.

This guide was produced by: Pro-Ject Audio Systems

The information was correct at the time of going to

press. The manufacturer reserves the right to make

changes to the technical speci

fication without prior

notice as deemed necessary to uphold the ongoing

process of technical development.

Indice

Altri manuali Pro-Ject Audio Systems Strumento di misura

Pro-Ject Audio Systems

Pro-Ject Audio Systems Measure it S2 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente