Profile Design TRI STEM Manuale utente

Tri Stem

TRI STEM

REVISION 01-04-18-2023

Tri Stem

INTRODUCTION

Thank you for purchasing this Profile Design Stem. These instructions apply to the Tri Stem.

Please read these instructions thoroughly before attempting to install this item. Proper installation is required for compliance with Profile Design's

warranty policy. If you are not familiar with installation of Aerobars or their accessories, please seek the assistance of your local Profile design dealer

by logging on to www.profile-design.com and using "dealer search" or by calling Profile Design's customer service number p.# 888.800.5999.

Note to Dealers: If you install this product for the consumer, please provide him/her with this owner’s manual after installation.

Tools and materials required:

• Assembly compound such as Finishline Fiber Grip™

• 4mm Allen key

• Torque Wrench with 4mm Hex bit

Your Stem kit should contain:

• One (1) aluminium stem body with two (2) M5x18 steerer clamp bolts

• One (1) aluminium stem faceplate with four (4) M5x18 bolts

• One (1) aluminium headset compression cap with one (1) M6x30 bolt

• One (1) plastic stem cover with two (2) M3x10 bolts

Tri Stem

Optional accessories compatible with this stem:

WARNING: Periodically check the stem for damage that could lead to degradation and weakening of the base material. Replace your stem if you

notice any damage from use or accident.

• Any Profile Design Basebar or Handlebar

• HSF Aeria Bottle

• HSF Aeroflow Bottle

If anything is missing from the Stem kit please contact your dealer.

Tri Stem

COMPONENT LIST

Tri Stem 105mm

QTY.

Req.

Part.#Ref.# Part Description

1539136Tri Srem 17.5° x 105mm Bk Logo w/ Bolts

Tri Stem

COMPONENT LIST

QTY.

Req.

Part.#Ref.# Part Description

1539137Tri Stem 17.5°x 80mm Bk Logo w/ Bolts

Tri Stem 85mm

Tri Stem

PART DRAWINGS

(31.8 x 80 mm)

(31.8 x 105 mm)

26 mm

40 mm

57.5 mm

26 mm

80 mm

105 mm

135.7 mm

160.7 mm

57.5 mm

Tri Stem

TORQUE SETTINGS

1 Bar clamp bolts M5x18mm 1Nm (8.8 inlbf)

2Steerer clamp bolts M5x18mm 5Nm (44 inlbf)

3 Headset cap bolt M3x10mm 6Nm (53 inlbf)

Ref.# Location Bolt Size Torque

Tri Stem

INSTALLATION INSTRUCTIONS

Externally routed headset

1. Install the stem on the fork steerer.

• Ensure the top of the steerer tube is level with or up to 2mm above the top of the stem clamp.

• Fit the included compression cap.

• Tighten the steerer clamp bolts enough that the stem won’t shift during the assembly process.

Note that this is not the final tightening of these bolts.

2. Apply assembly paste to the bar clamp of the stem.

3. This step depends on the style of basebar you are using.

• If the brake cables exit the basebar outside the stem attach the basebar to the stem and tighten

the faceplate bolts so they are snug.

• If the brake cables exit the basebar inside the stem, first route the cables through the bar, then

route them through the stem before attaching the faceplate and tightening the bolts to be snug.

• The front brake cable can be routed outside the stem or into the stem and out through the hole

in the base of the stem body.

4. If using electronic gears, the only way to route the cables into the stem is through the basebar (only

available on Wing Carbon bars and Aeria Ultimate), do this prior to fitting the basebar to the stem.

5. Complete the rest of the aerobar installation then brake and shifter cable setup according to the

manufacturer instructions.

6. Remove the bike from the workstand for final adjustments.

• Tighten the headset according to the headset manufacturers instructions.

• Tighten the steerer clamp bolts on the stem to a maximum of 5Nm.

• Adjust the angle of the basebar.

• Tighten the faceplate bolts to a maximum of 6Nm.

7. Once headset and cable installation is complete, fit the plastic cover over the steerer and torque

the bolts to a maximum of 2Nm.

Tri Stem

Internally routed headset

1. Route the brake and gear cables through the frame and out of the headset cap.

2. Install the stem on the fork steerer.

• As you install the stem guide the cables through the two slots in the stem and

out through the bar clamp area.

• Ensure the top of the steerer tube is level with or up to 2mm above the top of the

stem clamp.

• Fit the included compression cap.

• Tighten the steerer clamp bolts enough that the stem won’t shift during the

assembly process. Note that this is not the final tightening of these bolts.

3. Apply assembly paste to the bar clamp of the stem.

4. Install the bar, carefully guiding the cables into the basebar and out to their

appropriate locations.

5. Attach the faceplate and tighten the bolts to be snug.

6. Complete the rest of the aerobar installation then brake and shifter

cable setup according to the manufacturer instructions.

7. Remove the bike from the workstand for final adjustments.

• Tighten the headset according to the headset manufacturers instructions.

• Tighten the steerer clamp bolts on the stem to a maximum of 6Nm.

• Adjust the angle of the basebar.

• Tighten the faceplate bolts to a maximum of 6Nm.

8. Once headset and cable installation is complete, fit the plastic cover over the

steerer and torque the bolts to a maximum of 2Nm.

INSTALLATION INSTRUCTIONS

Tri Stem

Option 3Option 1 Option 2

A A A

A A A1B

BB B

1 1 1

CABLE ROUTE MAP

Brake Cables

Shifting (Electric Cables)

Indice

Altri manuali Profile Design Accessori per biciclette

Profile Design

Profile Design Sonic Bracket Manuale utente

Profile Design

Profile Design Canta Zero Manuale utente

Profile Design

Profile Design RM 10 Manuale utente

Profile Design

Profile Design Carbon Stryke Manuale utente

Profile Design

Profile Design Lightning Stryke Manuale utente

Profile Design

Profile Design WING20C+ Manuale utente

Profile Design

Profile Design A3a Manuale utente

Profile Design

Profile Design AERIA1 EVO Manuale utente

Profile Design

Profile Design Multi-Fit Manuale utente

Profile Design

Profile Design AEROPORT Manuale utente

Profile Design

Profile Design RM Single System Manuale utente

Profile Design

Profile Design WING/20c Manuale utente

Profile Design

Profile Design 43ASC Manuale utente

Profile Design

Profile Design AERIA ULTIMATE RACE Manuale utente

Profile Design

Profile Design DRV/GMR Series Manuale utente

Profile Design

Profile Design L2 Manuale utente

Profile Design

Profile Design 35SLC Manuale utente

Profile Design

Profile Design T2+ DL Manuale utente

Profile Design

Profile Design Swiftshift Manuale utente

Profile Design

Profile Design HSF 800 HYDRATION Manuale utente

Profile Design

Profile Design Split Second Manuale utente

Profile Design

Profile Design ERGO+ ARMREST KIT Manuale utente

Profile Design

Profile Design HSF Aeria Manuale utente

Profile Design

Profile Design Sonic CSX Manuale utente

Manuali Accessori per biciclette popolari di altre marche

Sigma

Sigma BC 16.16 Manuale utente

Playcore

Playcore Dero Setbacks Manuale utente

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuale utente

Cateye

Cateye RAPID X2 Manuale utente

buratti meccanica

buratti meccanica Clorofilla Trail Manuale utente

Shimano

Shimano SG-8R20 Istruzioni operative

BOB

BOB YAK Manuale utente

APLIC

APLIC 303303/20190717TW012 Manuale utente

SRAM

SRAM AXS BlipBox Manuale utente

Garmin

Garmin EDGE 500 Manuale utente

Shimano

Shimano FD-RX810 Manuale utente

Cateye

Cateye V2C - Manuale di istruzioni

KMART

KMART 43115907 Manuale utente

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuale utente

NVO Components

NVO Components STEM Manuale utente

DAXYS

DAXYS BP188 Manuale utente

XLC

XLC BV-W17 Manuale utente

Deda Elementi

Deda Elementi SUPERBOX Manuale utente