Profile Design HSF 800 HYDRATION Manuale utente

HSF/Aero HC 800

HSF 800 HYDRATION

REVISION 01-11-03-2020

HSF/Aero HC 800

Thank you for purchasing this Profile Design Hydration System. These instructions apply to both the standard and plus versions of the HSF/Aero HC

800.

Please read these instructions thoroughly before attempting to install this item. Proper installation is required for compliance with Profile Design's

warranty policy. If you are not familiar with installing cycling accessories, please seek the assistance of your local Profile design dealer by logging on to

www.profile-design.com and using "dealer search" or by calling Profile Design's customer service number p.# 888.800.5999

Note to Dealers: If you install this product for the consumer, please provide him/her with this owner’s manual after installation.

Tools and materials required:

• Needle nose pliers

• Scissors or a diagonal pliers

INTRODUCTION

HSF/Aero HC 800

Your hydration system should contain:

• Plastic bottle

• Plastic screw cap with fill port

• Plastic BTA mount with threaded inserts

• Plastic bottle cage with retention clip

• Garmin mount

• Drinking straw

• + model equipped with a magnet in the screw cap and a bit valve

• Standard model has a hose clip under the garmin mount

• Plastic zip ties

If anything is missing from the hydration system please contact your dealer.

HSF/Aero HC 800

COMPONENT LIST

HSF 800+

17 18 19 20 21

QTY.

Req. Part.# Ref.# Part Description

11Bottle - HSF 800

2Rear Cap - HSF 800+ Magnet System (Integration)

13Rear Cap - HSF 800

4 Top Cap - For HSF 800 Rear Top Cap

5 Latch -Axis Grip for HSF 800

Cage - Axis Grip

O Ring - Axis Grip

Garmin Mount - Base ( 800+ & Axis Grip)

Garmin Mount - Top (Axis Grip)

600212

B141

B142

B143

B146

414231

B147

B148

B149

B150

B117

B083

B096

WB139

WB138

274468

275673

313599

313597

313598

B118

BTA - HC MOUNT 2

O-Ring - Straw Stabilization

Straw - Silicon 280 mm

FC Bite Valve Dark gray

Magnet System - Movable - Aeria HSF (Integration)

Magnet System - Straw - Aeria HSF (Integration)

Rubber - Movable Magnet - Aeria HSF

Pin - 3 x 19 mm

Washer 5.3 x 13 x 1

Bolt - M3 x 8 FHB SL

Bolt - M5 x 10 FHB SL

Bolt - M5 x 14 BHB SL w/nylock

HSF/Aero HC 800

COMPONENT LIST

HSF 800

13 14 15 16 17

12 08

QTY.

Req. Part.# Ref.# Part Description

11Bottle - HSF 800

2Rear Cap - HSF 800

13Top Cap - For HSF 800 Rear Cap

4 Top Cap - For HSF 800 Rear Top Cap

Latch -Axis Grip for HSF 800

Cage - Axis Grip

O Ring - Axis Grip

Garmin Mount - Base - Straw (800 & Axis Grip)

Garmin Mount - Top (Axis Grip)

600212

B142

B151

B143

B146

414231

B147

B152

B149

B150

B117

B083

274468

275673

313596

313598

313597

BTA - HC MOUNT 2

O-Ring - Straw Stabilization

Straw - Silicon 280 mm

Pin - 3 x 19 mm

Washer 5.3 x 13 x 1

Bolt - M3 x6 FHB SL

Bolt - M5 x 10 FHB SL

Bolt - M5 x 14 BHB SL w/nylock

HSF/Aero HC 800

PART DRAWINGS

112 mm

310 mm

140 mm

84.5 mm

HSF/Aero HC 800

PRODUCT SPECIFIC SETUP LIMITATIONS

• The HSF/Aero HC 800 bottle can only be used with the KAG1 - Axis Grip Cage with Garmin Mount

• The HC Mount II is designed to fit on aerobar extensions 80mm-120mm wide (3.25in – 4.75in)

• The HSF/Aero HC 800 has been designed for a temperature range of -40 to 75deg C

HSF/Aero HC 800

INSTALLATION INSTRUCTIONS

1. To open the bottle, first remove it from the cage. (see instructions below on how to remove the bottle

from the cage)

2. Unscrew the cap by turning counter clockwise. (If the cap is at the top)

3. Once the threads disengage you will need to pull the cap the remaining distance.

4. Note that it will be slightly easier to do this if you open the fill port.

1. Place the wings of the HC Mount II on the extensions.

2. Route the zip ties around the extension and through the slots in the mount.

3. Use the pliers to pull the zip ties tight, alternatingly sides to ensure the mount is centered.

4. You must use two zip ties per side.

5. Once the mount is securely fastened, use the scissors or diagonal pliers to trim the zip ties, being

careful to not harm yourself or damage any of the components of the hydration system or bike.

Note that the mount can be installed on the lower side of the extensions if you wish to set the hydration

system lower.

1. Again, it will be easier to do this with the fill port open.

2. Carefully align the bottle with the dual lip seal on the cap.

3. Carefully push the cap down on the bottle making sure the gap between the two parts is even.

4. As you feel resistance to pushing further, start to turn the cap clockwise (again this is with the cap at

top) to engage the threads.

5. At this point it is best to observe the base of the bottle – turn the cap until the tab on the cap just

touches the tab on the bottle – this ensures correct alignment and sealing of the bottle.

6. Close the fill port.

1. Remove the bottle from the cage and remove the cap.

2. You can use a bottle brush to clean inside the bottle and cap.

3. A hose brush can be used to clean the straw.

4. The bottle could be placed in a dishwasher with the straw and straw gusset removed.

5. Do not use harsh chemical cleaners on your hydration system.

6. Once the system is clean and dry, reassemble and fit to your bike.

Opening the bottle:

Installing the system on a bike:

Closing the bottle:

Cleaning the system:

STOP

HSF/Aero HC 800

1. To remove the bottle first ensure that the hose is not attached to the magnet or clip.

2. Then depress the lever on the clip that is located at the rear of the bottle. (Hear clip click)

3. While holding the lever down, carefully pull the bottle forwards out of the cage.

1. Orient the bottle correctly with the guide channel on the base lined up with the front tab on the cage.

2. Slide the bottle into the cage until you hear a click from the retention clip.

3. Check to make sure that the cage and guide channel are correctly matched.

4. If the bottle has not seated correctly, depress the retention lever and re-align the guide channel.

Removing the bottle: Installing the bottle:

PUSH

HSF/Aero HC 800

1. To drink during a race.

a. Remove the straw from the clip or magnet and place the end in your mouth.

b. If the hydration system is equipped with a bite valve ensure this is oriented with the slit vertically in

your mouth and that the valve is pulled open.

c. Suck on the straw to take a drink.

d. Place the straw back in the clip or on the magnet

2. To fill the bottle

a. Open the fill port by pulling the tab back towards your body.

b. Insert the nozzle of your refill into the fill port.

c. Squeeze the refill bottle until it is empty.

d. Close the fill port.

Using the bottle:

3. To install a Garmin© GPS unit

a. Note that the KAG1 - Axis Grip Cage with Garmin© mount is only compatible with Edge series

units.

b. Place the tabs on the base of the Garmin© into the mount and gently make a quarter turn of the

head unit to engage it with the mount.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Profile Design Accessori per biciclette

Profile Design

Profile Design Supersonic Ergo 35c Manuale utente

Profile Design

Profile Design CGT Manuale utente

Profile Design

Profile Design AEROPORT Manuale utente

Profile Design

Profile Design L2 Manuale utente

Profile Design

Profile Design Vertex 80 Manuale utente

Profile Design

Profile Design DRV/GMR Series Manuale utente

Profile Design

Profile Design Carbon Stryke Manuale utente

Profile Design

Profile Design 43ASC Manuale utente

Profile Design

Profile Design Carbon X 1.5 Manuale utente

Profile Design

Profile Design Aeria Manuale utente

Profile Design

Profile Design ERGO+ ARMREST KIT Manuale utente

Profile Design

Profile Design Swiftshift Manuale utente

Profile Design

Profile Design Sonic CSX Manuale utente

Profile Design

Profile Design Canta Zero Manuale utente

Profile Design

Profile Design DRV SIZER BAR Manuale utente

Profile Design

Profile Design RZ3 Manuale utente

Profile Design

Profile Design TRI STEM Manuale utente

Profile Design

Profile Design RM 10 Manuale utente

Profile Design

Profile Design AERIA1 EVO Manuale utente

Profile Design

Profile Design 35SLC Manuale utente

Profile Design

Profile Design WING/20c Manuale utente

Profile Design

Profile Design Carbon X Manuale utente

Profile Design

Profile Design AERIA ULTIMATE RACE Manuale utente

Profile Design

Profile Design WING20C+ Manuale utente

Manuali Accessori per biciclette popolari di altre marche

Sigma

Sigma BC 16.16 Manuale utente

Playcore

Playcore Dero Setbacks Manuale utente

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuale utente

Cateye

Cateye RAPID X2 Manuale utente

buratti meccanica

buratti meccanica Clorofilla Trail Manuale utente

Shimano

Shimano SG-8R20 Istruzioni operative

BOB

BOB YAK Manuale utente

APLIC

APLIC 303303/20190717TW012 Manuale utente

SRAM

SRAM AXS BlipBox Manuale utente

Garmin

Garmin EDGE 500 Manuale utente

Shimano

Shimano FD-RX810 Manuale utente

Cateye

Cateye V2C - Manuale di istruzioni

KMART

KMART 43115907 Manuale utente

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuale utente

NVO Components

NVO Components STEM Manuale utente

DAXYS

DAXYS BP188 Manuale utente

XLC

XLC BV-W17 Manuale utente

Deda Elementi

Deda Elementi SUPERBOX Manuale utente