Quantum DXi4510 Manuale dell'operatore

www.quantum.com

DXi4500 Installation and

Configuration Guide

Contents

DXi4500 Configurations......................... 2

Choosing a Location .............................. 2

Installation Requirements.................. 2

Rack Space Requirements .................. 3

Environmental Conditions ................. 3

Preparing for the Installation ................ 3

Taking ESD Precautions ...................... 3

Unpacking the DXi4500 ......................... 4

Installing the DXi4500 System............... 6

Locating the Mounting Position ........ 6

Installing the DXi4500 ....................... 7

Cabling the DXi4500 ........................ 11

Initial Configuration............................. 11

Accessing the DXi4500, Remote

Management Interface .................... 12

Completing the Setup Wizard ......... 15

Connecting the Ethernet Cables ...... 19

Creating a Typical Backup

Configuration................................... 20

DXi4500 Installation and

Configuration Guide

This guide provides basic installation and configuration instructions for the

DXi4500 system (see Figure 1). Make sure to read the DXi4500 Site

Planning Guide before starting your installation. The Site Planning Guide is

included on the documentation CD provided with your DXi4500 system.

Note: Make sure to take the online training for the DXi4500 in order to

make the best use of your product. The online training is available

at www.quantum.com/ServiceandSupport/StorageCareLearning/

Index.aspx

This instruction uses the following conventions:

Note: Notes emphasize important information related to the main topic.

Caution: Cautions indicate potential hazards to equipment and are

included to prevent damage to equipment.

WARNING: Warnings indicate potential hazards to personal safety and

are included to prevent injury.

Figure 1 DXi4500 System

2DXi4500 Configurations

DXi4500 Installation and Configuration Guide

DXi4500 Configurations

The DXi4500 is available in the following configurations (see Ta b l e 1 ):

Table 1 DXi4500

Configurations

Configuration Number of Hard Drives Hard Drive Capacity

DXi4510 (2.2 TB Usable Capacity) 8500 GB

DXi4520 (4.4 TB Usable Capacity) 81 TB

Choosing a Location

Quantum recommends installing the DXi4500 system in a controlled or restricted area

to prevent access by untrained personnel. In addition, Quantum recommends that

system installation be performed only by qualified IT personnel.

When choosing an installation site for the DXi4500 system, consider the following

requirements:

•Installation Requirements

•Rack Space Requirements

•Environmental Conditions

Installation

Requirements

Review the

DXi4500 Site Planning Guide

(PN 6-66909) to ensure that your site meets the

installation requirements for the DXi4500.

Preparing for the Installation 3

DXi4500 Installation and Configuration Guide

Rack Space

Requirements

Tabl e 2 contains the rack requirements for the DXi4500 components.

Table 2 Rack Requirements

DXi4500

Height 2U, 3.40 in (8 6 cm)

Width (side to side) 17.19 in (43.6 cm)

Depth (front to back) 24.09 in (61 cm)

Weight (stand alone) 49.5 lbs (22.5 Kg)

Air Clearance Open 4 in (10.2 cm) behind unit for proper air flow

Environmental

Conditions

The installation site must have the following environmental conditions:

• Humidity: 20% to 80% (non-condensing)

• Temperature: 10 to 35 °C (50 to 95 °F) 35 °C Max, Altitude = 900 m or 2952.75 ft

(28 °C Max, Altitude = 3048 m or 10,000 ft)

These environmental conditions apply when the DXi4500 system is in operation.

Note: For additional specifications, refer to the

Quantum DXi4500 User’s Guide

(PN 6-

66904) located on the documentation CD.

Preparing for the Installation

Before you begin the installation procedure in this section, make the following

preparations as described in this section:

•Taking ESD Precautions on page 3

Taking ESD Precautions Some components within the DXi4500 system contain static-sensitive parts. To avoid

damaging these parts while performing installation procedures, always observe the

following precautions:

• Keep the DXi4500 system turned off during all installation procedures.

• Keep static-sensitive parts in their original shipping containers until ready for

installation.

• Do not place static-sensitive parts on a metal surface. Place them inside their

protective shipping bag or on an antistatic mat.

4Unpacking the DXi4500

DXi4500 Installation and Configuration Guide

• Avoid touching connectors and other components.

Note: Dry climates and cold-weather heating environments have lower relative

humidity and are more likely to produce static electricity.

Unpacking the DXi4500

By following these instructions, you help ensure that the system will continue to be

safeguarded after it arrives at the installation site.

Unpack and remove the following components from the packing materials (see

Figure 2):

• DXi4500 chassis

• Front bezel with key

• (4) power cords, 2 U.S. and 2 international cables

• Ethernet cables

• Left and right slide assemblies

• Cable-management arm

• Left and right cable-management arm ramp assemblies

• DXi4500 Quick Reference and Documentation CD

• DXi4500 Installation and Configuration Instructions

• Accessory kit

Caution: Do NOT discard the packing materials after the system is unpacked. The

packaging materials must be used if the system is relocated.

WARNING: The DXi4500 weighs 49.5 lbs (22.5 Kg). Two people are required to lift the

chassis.

Unpacking the DXi4500 5

DXi4500 Installation and Configuration Guide

Figure 2 Unpacking the

DXi4500

Slide rails

Tie bands

Chassis rails Front bezel

6Installing the DXi4500 System

DXi4500 Installation and Configuration Guide

Installing the DXi4500 System

Installing the DXi4500 in a rack consists of the following steps:

1Locating the Mounting Position on page 6

2Installing the DXi4500 on page 7

3Cabling the DXi4500 on page 11

Locating the Mounting

Position

The DXi4500 systems is designed to fit in a standard 19 inch wide rack. It is important

for the chassis installation to locate the hole pattern in the rack rails. You must allow 2U

(3.5 in (8.9 cm)) of vertical space for the DXi4500 system. Rack cabinets that meet EIA-

310 standards have an alternating pattern of three holes per rack unit with center-to-

center hole spacing (beginning at the top hole of a 1-U space) of 15.9 mm, 15.9 mm,

and 12.7 mm (0.625 inch, 0.625 inch, and 0.5 inch) for the front and back vertical rails

(see Figure 3). Rack cabinets may have round or square holes.

Figure 3 Rail Hole Pattern

1 U (44 mm [1.75 inches])

12.7 mm (0.5 inch)

15.9 mm (0.625 inch)

12.7 mm (0.5 inch)

1 U (44 mm [1.75 inches])

WARNING: If the rack is empty at the time of installation, do NOT install the DXi4500

chassis too high in the rack. The weight of the chassis may cause the rack

to become “top heavy” and unstable if installed in the top of an empty

rack.

To mark the rack, perform the following step:

1Place a mark (or tape) on the rack's front vertical rails where you want to locate the

bottom of the system you are installing in the rack. The bottom of each 1-U space is

at the middle of the narrowest metal area between holes (marked with a horizontal

line on some rack cabinets).

Installing the DXi4500 System 7

DXi4500 Installation and Configuration Guide

Installing the DXi4500 Installing the DXi4500 consists of the following steps:

•Installing the DXi4500 Rack Mounting Rails

•Installing the DXi4500 Chassis

Installing the DXi4500 Rack Mounting Rails

1Install the rack mounting rails (see Figure 4 for square holes and Figure 5 for Round

holes):

aPosition the left and right rail end pieces of the rail module labeled FRONT

facing inward and orient each end piece to seat in the square holes on the front

side of the vertical rack flanges. Align each end piece to seat the pegs in the

bottom hole of the first U space and the top hole of the second U space.

bEngage the back end of the rail until it fully seats on the vertical rack flange and

the second tooth on the latch locks in place.

Note: To remove the rack mounting rails, pull the Release latch located on the

front of the rail.

Figure 4 Installing the Rack

Mounting Rails (Square Holes)

Front side of rack rails

Front of rack

Back of rack

Rail teeth

Rail pegs

Second tooth

engaged

Release

button

Release

button

8Installing the DXi4500 System

DXi4500 Installation and Configuration Guide

Figure 5 Installing the Rack

Mounting Rails (Round Holes)

2Place the DXi4500 on a level surface and align the four keyhole slots on the chassis

rails with the corresponding pins on the system. Slide the chassis rails towards the

back of the system until each one locks into place (see Figure 6).

WARNING: The DXi4500 weighs 49.5 lbs (22.5 Kg). Two people are required to lift the

chassis.

Note: To disengage the chassis rails, pull the latch and push the rails toward the front

of the chassis.

Front side of rack rails

Front of rack

Back of rack

Rail teeth

Rail pegs

Second tooth

engaged

Release

button

Release

button

Installing the DXi4500 System 9

DXi4500 Installation and Configuration Guide

Figure 6 Installing the Chassis

Rails

Front

Back

Chassis rails

Latch

10 Installing the DXi4500 System

DXi4500 Installation and Configuration Guide

Installing the DXi4500 Chassis

WARNING: Ensure that the system is properly supported until the chassis rails are

locked into the slide rails on both sides.

1To install the DXi4500 chassis (see Figure 7):

WARNING: The DXi4500 weighs 49.5 lbs (22.5 Kg). Two people are required to lift the

chassis.

aPull the slide rails out of the rack until they lock into place.

bAlign and insert the ends of the chassis rails into the ends of the slide rails. Push

the system inward until the chassis rails lock into place.

cPush or pull the blue tab located near the front of the system and slide the

system into the rack.

Figure 7 Installing the

DXi4500 Chassis

Slide rails extended

DXi4500 chassis

Blue tab

Chassis rails

Altri manuali per DXi4510

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Quantum Magazzinaggio

Quantum

Quantum DLT Series Istruzioni per l'installazione

Quantum

Quantum ValueLoader LTO-2 Manuale utente

Quantum

Quantum DXi4500 Manuale utente

Quantum

Quantum DX100 Manuale utente

Quantum

Quantum ActiveScale X100 Manuale utente

Quantum

Quantum DLTtape DLT1 Manuale utente

Quantum

Quantum Scalar i2000 Manuale utente

Quantum

Quantum SNC 4500 Manuale utente

Quantum

Quantum Scalar i40 Istruzioni operative e di sicurezza

Quantum

Quantum LTO3 A-Series Manuale utente

Quantum

Quantum StorNext QD6000 Manuale utente

Quantum

Quantum DXi7500 Manuale tecnico

Quantum

Quantum QXS-448 Manuale utente

Quantum

Quantum E240 Manuale utente

Quantum

Quantum StorNext QD7000 Manuale

Quantum

Quantum LTO-3 Manuale utente

Quantum

Quantum ActiveScale P100E3 Manuale utente

Quantum

Quantum PX502 Manuale di riferimento

Quantum

Quantum Scalar LTFS Manuale elenco delle parti

Quantum

Quantum Q2000 Manuale utente

Quantum

Quantum DPM 5500 Manuale utente

Quantum

Quantum DLT-V4 Manuale

Quantum

Quantum DLT 8000 Manuale

Quantum

Quantum DXi6902 Manuale dell'operatore

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente