Quantum StorNext QM1200 Manuale utente

StorNext QM1200/QS1200/QS2400 Base System

Replacing a Power-Fan Canister

6-67555-02 Rev B *6-67555-02 B*

ii Replacing a Power-Fan Canister

StorNext QM1200/QS1200/QS2400 Base System, Replacing a Power-Fan Canister, 6-67555-02 Rev B, April 2015, Product

of USA.

Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including

but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation

may revise this publication from time to time without notice.

Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior written

authorization of Quantum Corporation is prohibited by law and constitutes a punishable violation of the law.

TRADEMARK STATEMENT

Quantum, the Quantum Logo, Backup. Recovery. Archive. It's What We Do., Be Certain, Be Quantum Certain, DLT, the DLT

Logo, DLTSage, DLTtape, the DLTtape Logo, DXi, DXi Accent, Dynamic Powerdown, FastSense, FlexLink, GoProtect,

GoVault, iLayer, Lattus, MediaShield, Optyon, Pocket-sized., Well-armored., Preserving the World's Most Important Data.

Yours., Q-Cloud, Quantum Certain, Quantum Certainty, Quantum vmPRO, Scalar, SDLT, SiteCare, SmartVerify,

StorageCare, StorNext, Super DLTtape, SuperLoader, and Vision are either registered trademarks or trademarks of

Quantum Corporation and its affiliates in the United States and/or other countries. All other trademarks are the property

of their respective owners.

Products mentioned herein are for identification purposes only and may be registered trademarks or trademarks of their

respective companies. All other brand names or trademarks are the property of their respective owners.

Quantum specifications are subject to change.

StorNext QM1200/QS1200/QS2400 Base System - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 1 -

Replacing a Power-Fan Canister in the StorNext

QM1200/QS1200/QS2400 Base System

Before you start to replace the power-fan canister in the StorNext QM1200/QS1200/QS2400 Base System, gather

antistatic protection and a replacement power-fan canister.

You can determine whether you have a failed power-fan canisterin two ways:

The Recovery Guru directs you to replace a failed power-fan canister.

You locate the failed power-fan canister by checking the Power Service Action Required LED.

Locating the Failed Power-Fan Canister

1. Refer to Figure 1 to locate the power-fan canister within the base system.

Figure 1 Power-Fan Canister Locations

1. Controller Canister

2. Power-Fan Canister

2. Check the Power Service Action Required LED to locate the failed power-fan canister (Figure 2).

ATTENTION Possible equipment damage – If you perform this procedure with the power turned on, you

must complete it within three minutes to prevent the possibility of overheating the equipment.

ATTENTION Possible hardware damage – To prevent electrostatic discharge damage to the tray, use proper

antistatic protection when handling tray components.

StorNext QM1200/QS1200/QS2400 Base System - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 2 -

Figure 2 Power-Fan Canister Service Action LEDs

1. Standby Power-Fan LED (Green)

2. Power-Fan DC Power LED (Green)

3. Power-Fan Service Action Allowed LED (Blue)

4. Power-Fan Service Action Required LED (Amber)

5. Power-Fan AC Power LED (Green)

Gathering Support Data/Unpacking Power-Fan Canister

3. Gather support data about your storage array by using one of these methods:

—Use the storage management software to collect and save a support bundle of your storage array. From the

Array Management Window, select Monitor >> Health >> Collect Support Data. Then name and specify a

location on your system where you want to store the support bundle.

—Use the command line interface (CLI) to run the save storageArray supportData command to gather

comprehensive support data about the storage array. For more information about this command, refer to

Command Line Interface and Script Commands. Running this command can temporarily impact performance

on your storage array.

4. Did the Recovery Guru direct you to replace a failed power-fan canister?

—Yes – Go to step 6.

—No – Run the Recovery Guru to identify the failed component, and go to step 5.

5. If the Recovery Guru has directed you to replace the power-fan canister and the blue Power-Fan Service Action

Allowed LED is not on, use either the command line or the GUI to prepare the power-fan canister for removal

a. On the command line, type this command and press Enter:

SMcli <ctrl_IP1> <ctlr_IP2> -c “Set tray [trayID] powerfanCanister [left|right]

service Allowed Indicator=on;”

In this command:

—<ctlr_IP1> <ctlr_IP2> are the identifier of the controller to which the expansion unit is assigned.

—[trayID]is the identifier of the expansion unit that contains the power-fan canister that you want to

replace. Drive tray ID values are 0 to 99. Be sure to type the square brackets around the identifier.

—[left|right] is the identifier of the power-fan canister you want to replace. Valid values are left or

right. Be sure to type the square brackets around the value.

b. On the GUI, click on the image of the tray that contains the power-fan canister you want to replace. From the

Array Management Window toolbar, select Hardware >> Prepare for Removal.

6. Put on antistatic protection.

StorNext QM1200/QS1200/QS2400 Base System - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 3 -

7. Unpack the new power-fan canister.

a. Set the new power-fan canister on a flat, static-free surface near the base system.

b. Save all packing materials in case you need to return the power-fan canister.

Removing the Power-Fan Canister

NOTE If a fault is detected, the amber Power-Fan Service Action Required LED is on. If you can safely remove the power-fan canister,

the blue Power-Fan Service Action Allowed LED is on.

1. Turn off the Power switch on the power-fan canister that has failed (Figure 3).

Figure 3 Power Switch on the Power-Fan Canister

1. Power Switch

2. Remove the plastic strain relief from the power cord.

3. Unplug the power cord from the failed power-fan canister.

4. Remove the power-fan canister from the base system (Figure 4).

a. Rotate the power-fan canister latches outward to disengage the power-fan canister.

b. Use the power-fan canister latches as handles to pull the power-fan canister out of the drive tray.

NOTE While removing the power-fan canister, you might notice an increase in fan speed. The fan speed returns to normal after you

have replaced the power-fan canister.

Figure 4 Removing and Replacing a Power-Fan Canister

1. Power-Fan Canister Latches

StorNext QM1200/QS1200/QS2400 Base System - Replacing a Power-Fan Canister April 2015

Quantum Corporation

- 4 -

Installing the Power-Fan Canister

1. Slide the replacement power-fan canister all the way into the tray. Rotate the power-fan canister latches towards

the center to lock the power-fan canister into place.

2. Make sure that the Power switch on the replacement power-fan canister is turned off, and plug in the power cord.

3. Attach the plastic strain relief to the power cord, and make sure that it fits snugly up against the power-fan

canister.

4. Turn on the Power switch on the replacement power-fan canister.

5. Check the green Input AC Power LED and the amber Power Service Action Required LED on the new power-fan

canister (Figure 2).

6. Based on the LED status, perform one of these actions:

—The Input AC Power LED is on, and the Power Service Action Required LED is off – Go to step 8.

—The Input AC Power LED is off, or the Power Service Action Required LED is on – Check that the power-fan

canister is installed correctly. Reinstall the power-fan canister. Go to step 7.

7. Did this action correct the problem?

—Yes – Go to step 8.

—No – If the problem has not been resolved, contact your Customer and Technical Support representative.

8. Check the status of all of the trays in the storage array.

9. Does any component have a Needs Attention status?

—Yes – Click the Recovery Guru toolbar button in the Array Management Window, and complete the recovery

procedure. If the problem has not been resolved, contact your Customer and Technical Support

representative.

—No – Go to step 10

10. Remove the antistatic protection.

11. Gather support data about your updated storage array by using one of these methods:

—Use the storage management software to collect and save a support bundle of your storage array. From the

Array Management Window toolbar, select Monitor >> Health >> Collect Support Data. Then name and

specify a location on your system where you want to store the support bundle.

—Use the CLI to run the save storageArray supportData command to gather comprehensive support data

about the storage array. For more information about this command, refer to Command Line Interface and

Script Commands. Running this command can temporarily impact performance on your storage array.

Altri manuali per StorNext QM1200

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Quantum Magazzinaggio

Quantum

Quantum Superloader 3 Manuale utente

Quantum

Quantum DLT 4700 Manuale utente

Quantum

Quantum DLTtape SDLT 600 Scheda informativa del prodotto

Quantum

Quantum FastStor 2 Manuale utente

Quantum

Quantum SuperLoader 3A Series Manuale utente

Quantum

Quantum Scalar 24 Istruzioni operative

Quantum

Quantum DPM 5500 Manuale utente

Quantum

Quantum DXi3500 Manuale utente

Quantum

Quantum LTO 1U Manuale utente

Quantum

Quantum Scalar LTFS Manuale per l'uso e la cura

Quantum

Quantum FastStor 1 Manuale utente

Quantum

Quantum Scalar i6000 Manuale tecnico

Quantum

Quantum PX502 Manuale di riferimento

Quantum

Quantum DXi6900 Guida rapida

Quantum

Quantum SNC 4000 Manuale di istruzioni

Quantum

Quantum DLTtape DLT 4000 Manuale utente

Quantum

Quantum ATL 7100 Manuale

Quantum

Quantum DLTtape SDLT 600 Manuale utente

Quantum

Quantum LTO-4 (Model B) Manuale utente

Quantum

Quantum RDX 8000 Manuale utente

Quantum

Quantum LTO 3A Manuale di istruzioni

Quantum

Quantum DX100 Manuale utente

Quantum

Quantum PX500 Series Manuale di istruzioni

Quantum

Quantum Scalar i500 Guida rapida

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente