Raven AccuBoom Manuale utente
TerraGator with Liquid Bed
AccuBoom™ Installation Manual
P/N 016-0171-062 Rev A 09/15
Copyright 2010, 2015
While every effort has been made to ensure the accuracy of this document,
Raven Industries assumes no responsibility for omissions and errors. Nor is any
liability assumed for damages resulting from the use of information contained
herein.
Raven Industries shall not be held responsible or liable for the effects of
atmospheric conditions and sunspot activity on the performance of our products.
Raven Industries cannot guarantee the accuracy, integrity, continuity, or
availability of the GPS signal from the U.S. Department of Defense/NAVSTAR
GPS satellites, the OmniSTAR correction service, or the WAAS correction
service. Raven Industries accepts no responsibility for the use of the signal for
other than the stated purpose.
Raven Industries shall not be responsible or liable for incidental or consequential
damages or a loss of anticipated benefits or profits, work stoppage or loss, or
impairment of data arising out of the use, or inability to use, this system or any of
its components.
Disclaimer
SECTION 1
INTRODUCTION
Congratulations on your purchase of the Raven AccuBoom system! This system is
designed to provide worry free turn on and turn off of your booms with respect to the as-
applied coverage map. The following instructions are designed to assist you in the proper
installation of the AccuBoom system. See the Viper Installation and Operation Manual
for instructions on setting up the software and using the AccuBoom system. You will also
need a valid AccuBoom Control activation key for your Viper in order to activate the
AccuBoom system.
IMPORTANT: All boom switches must remain in the ON
position while AccuBoom control is in operation!
COMPONENTS NEEDED
Terragator with Liquid Bed Kit P/N 9-117-0171-079 including:
CAN AccuBoom Control Node – P/N 063-0172-316
AccuBoom Software Activation Key – P/N 077-0180-010
Terragator With Liquid Bed AccuBoom Cable – P/N 115-0171-701
CAN Tee Cable 12 foot – P/N 115-0171-362
AccuBoom Installation Sheet, Terragator With Liquid Bed – 016-0171-062
P/N 016-0171-062 Page2 of 7
SECTION 2
INSTALLATION
Use the following procedure to properly install the CAN AccuBoom system on a
Terragator With Liquid Bed:
1. Connect AccuBoom cable to AccuBoom node.
a. Connect the rectangular connectors from the AccuBoom Cable P/N 115-
0171-701 to the CAN Accuboom Node P/N 063-0172-316.
2. Mount the CAN AccuBoom node behind the Air Box.
a. Locate the Terragator boom cable connectors located on the right side of
the Air Box. These connectors are 12 pin Deutsch connectors.
P/N 016-0171-062 Page3 of 7
b. Mount the Raven CAN AccuBoom Node P/N 063-0172-316 within 5 feet
of the air box connectors.
3. Connect AccuBoom cable to the sprayer boom harness.
a. Unplug the Terragator boom cable from the Air Box.
P/N 016-0171-062 Page4 of 7
b. Tee in the AccuBoom Cable P/N 115-0171-701 between the Terragator
boom cable and the boom harness cable.
4. Route the CAN and power cables from AccuBoom harness to the main harness.
a. Connect a 12 foot CAN tee cable P/N 115-0171-362 to the CAN
connector located on the AccuBoom Cable P/N 115-0171-701.
b. Route the 12 foot CAN Tee Cable P/N 115-0171-362 and the power cable
from the AccuBoom Cable P/N 115-0171-701 to the CAN and CAN
Power connection located behind the operator ladder.
P/N 016-0171-062 Page5 of 7
5. Connect CAN cable to Product CANbus.
a. Remove the CAN Tee terminator from the Product Control CAN cable
located directly behind the operator ladder.
b. Connect the CAN tee cable P/N 115-0171-362 to the CAN connection
where the CAN Terminator P/N 063-0172-369 was previously removed
from.
c. Connect the CAN Terminator P/N 063-1072-369 to the other Tee end of
the CAN Tee Cable P/N 115-0171-362 located near the AccuBoom node
and secure in place.
P/N 016-0171-062 Page6 of 7
6. Connect power and ground.
a. Locate the CAN power connector located in the area behind the operator
ladder.
b. Connect the power connector from the AccuBoom Cable P/N 115-0171-
701 to the Terragator CAN power connection.
7. The Terragator With Liquid Bed CAN AccuBoom installation is complete.
P/N 016-0171-062 Page7 of 7
SECTION 3
SYSTEM TROUBLESHOOTING
The CAN AccuBoom Node P/N 063-0172-316 has additional features to allow the user
to diagnose the AccuBoom system. The CAN AccuBoom node has a plastic window in
the case that allows the user to view green diagnostic lights. The picture below shows the
positioning and function of each of the LED lights.
Logic Power: Lit when
12VDC logic power is
available at the node.
Micro 1 Hz: Flashes at 1 Hz
interval when processor is
active.
CAN Rx: Flashes when CAN
messages are being received.
CAN Tx: Flashes when CAN
messages are being transmitted.
High Current Power: Lit
when High Current Power is
applied to the node.
Logic Power
Micro 1 Hz
CAN Rx
CAN Tx
High Current Power
Altri manuali per AccuBoom
15
Indice
Altri manuali Raven Sistema di controllo
Raven
Raven AccuBoom Manuale utente
Raven
Raven DCS 410 Supplemento
Raven
Raven AccuBoom Manuale utente
Raven
Raven SCS 340 Manuale
Raven
Raven AccuFlow Manuale utente
Raven
Raven SmarTrax Manuale utente
Raven
Raven SCS-330 Supplemento
Raven
Raven RCM-Sprayer Hawkeye 2 Manuale utente
Raven
Raven SCS 440 Manuale utente
Raven
Raven CR Series Manuale utente
Raven
Raven SCS 460 Manuale
Raven
Raven RCM-Sprayer Hawkeye 2 Manuale utente
Raven
Raven Envizio Pro Manuale utente
Raven
Raven RCM Manuale per l'uso e la cura
Raven
Raven AccuBoom Manuale utente
Raven
Raven Viper Pro Manuale utente
Raven
Raven AccuBoom Manuale utente
Raven
Raven RS1/HDU Manuale utente
Raven
Raven SBGUIDANCE SMARTRAX MD Manuale utente
Raven
Raven AutoBoom Manuale utente
