Ricoh S7 D3DS Guida rapida

Double-feed Kit S7

Machine Code:D3DS

Field Service Manual

Ver 1.0

Latest Release: Nov, 2016

Initial Release: Nov, 2016

Table of Contents

1. Install.................................................................................................................................................................................. 2

Double-feed Kit S7 D3DS..................................................................................................................................................... 2

Accessories........................................................................................................................................................................ 2

Installation.......................................................................................................................................................................... 3

1.Install

Install

Double-feed Kit S7 D3DS

Accessories

No.

Description

Q’ty

1 Double-feed Sensor 1 (Emitter) 1

2 Double-feed Sensor 2 (Receiver) 1

3 Double-feed Sensor Board 1

4 Clamp 1

5 Long Harness (2-pin) 1

6 Long Harness (7-pin) 1

7 Shielded Harnesses 1

8 Short Harness (13-pin) 1

9 Screws M3x6 4

10 Screws M3x8 2

1.Install

Installation

Remove ADF Covers

1. Set the saddle clamp on the double-feed sensor board.

2. At the back of the machine, remove the cap and screw from the rear cover.

3. Raise the feed cover, and then remove the screw from the top edge of the rear cover.

4. Press the tab [A] on the end of the rear cover to release the cover, and then rotate the cover [B] down slowly.

1.Install

5. Disconnect the bottom tabs, and then remove the rear cover.

6. At the front, raise the ADF slightly.

7. Disconnect the top edge of the front cover. The embossed arrow [A] shows which direction to slide the cover to

unlock the tabs..

1.Install

8. Push the front cover [A] to the left, and then remove it [B].

9. Lower the ADF.

Remove Feed Cover, Upper Guide

1. At the left rear corner of the ADF, disconnect and free the shielded harnesses.

1.Install

2. At the front, remove the pivot screw.

3. Disconnect the hinge arm.

4. Carefully disconnect the cover at the rear [A].

5. At the front, disconnect the hinge arm [B].

1.Install

6. Remove the feed cover.

7. Lay the feed over on a flat clean surface as shown, and then disconnect the upper guide.

8. Release the edge of the upper guide from the posts.

9. Swing the upper guide up, and then remove it.

Remove Original Shielded Harnesses

1. Turn the upper guide [A] upside down.

1.Install

2. Disconnect the ground wire [B].

3. Remove the sensor bracket.

4. Disconnect the skew correction sensor [A] (white connector).

5. Disconnect the separation sensor [B] (black connector).

•These sensor harnesses must be re-connected as shown.

Indice

Altri manuali Ricoh Accessori per stampanti

Manuali Accessori per stampanti popolari di altre marche

Star Micronics

Star Micronics TSP800 Series Manuale utente

REA

REA JET HR pro 2K Manuale utente

HP Laserjet,Color Laserjet 4si Manuale utente

oliser

oliser MS 45 Manuale utente

Roland

Roland DU2-64 Istruzioni e ricette

Xerox

Xerox EFI EXP6000 Manuale utente

Canon

Canon Finisher-T1 Manuale utente

Sharp

Sharp FO-1MK Manuale utente

Labelmate

Labelmate PM-300 Manuale utente

Epson

Epson T6248 Manuale operativo

Epson

Epson OT-BZ20 Manuale utente

Canon

Canon TonerRobot EP-27 Manuale utente

GBC

GBC 16 Series Manuale utente

Canon

Canon INNER 2-WAY TRAY-E1 Manuale operativo e di manutenzione

Develop

Develop SD-509 Manuale utente

Kyocera

Kyocera KM-6230 Manuale

Triumph Adler

Triumph Adler DF-710 Manuale

Citizen

Citizen CBM-202PC Series Manuale utente