Roger IOS-1 Manuale utente
Roger Access Control System
IOS-1
Input-output simulator
User Manual
Product version v1.0
Document version: Rev. A
IOS-1 input-output simulator Rev.A.doc 2/21/2011
Strona 2z 4
General
IOS-1 module enables simulation of NO/NC input lines as well as visualization of status at output
lines (both relay and transistor types). The module can be used for education, testing or
demonstration in regard of alarm and access control devices. IOS-1 does not require power supply.
Circuit for input simulation and circuit for visualization of output status are independent of each
other.
Operation
General diagram of operation and exemplary application of IOS-1 are shown in figure below.
Z and COM terminals are used for simulation of input line. Input line can be configured by means of
jumpers as NO (Normally Open) or as NC (Normally Close). In case of NO setting, pressing TRIG.
button results in activation of Q1 output transistor and consequently shorting of Z terminal with
GND. In case of NC setting, output transistor is normally activated, Z and COM terminals are shorted
and pressing of TRIG. button results in deactivation of output transistor and consequently
disconnection between Z and GND terminals.
Note: COM terminal must be connected to lower potential than Z terminal. Typically COM terminal at
IOS-1 module is connected to GND or COM terminal of the tested device.
+12V and GND terminals enable visualization of status at output line. Voltage feeding in range of
5..15V between mentioned terminals results in LED lighting up on board. LED activation can be
caused by negative voltage at GND terminal or positive voltage at +12V terminal. Typically, such
solution enables signaling of status for any relay or transistor output line with negative or positive
output voltage.
IOS-1 input-output simulator Rev.A.doc 2/21/2011
Strona 3z 4
Technical Specification
Parameter Characteristics
Environmental class
(according to EN
50131-1)
Class I, indoor conditions, temperature range: +5°C to +40°C, relative
humidity: 0 to 95% (non condensing)
Module dimensions 35 X 43 mm
Module weight ~ 10g
Certificates CE
Product History
Hardware Firmware Date Description
v1.0 - Initial version of the product
IOS-1 input-output simulator Rev.A.doc 2/21/2011
Strona 4z 4
Ordering information
IOS-1 I/O Simulator module (electronic module only)
This symbol placed on a product or packaging indicates that the product should
not be disposed of with other wastes as this may have a negative impact on the
environment and health. The user is obliged to deliver equipment to the
designated collection points of electric and electronic waste. For detailed
information on recycling, contact your local authorities, waste disposal company
or point of purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to health and
the environment. Weight of the equipment is specified in the document.
Contact
Roger sp.j.
82-400 Sztum
Gościszewo 59
Tel.: +48 55 272 0132
Fax: +48 55 272 0133
Tech. support: +48 55 267 0126
E-mail: biuro@roger.pl
Web: www.roger.pl
Indice
Altri manuali Roger Sistema di controllo
Roger
Roger MCT80M Manuale utente
Roger
Roger H85/TDR Manuale del prodotto
Roger
Roger H85/TDR Manuale del prodotto
Roger
Roger MC16-RAW-KIT Manuale utente
Roger
Roger MCT62E Manuale utente
Roger
Roger B73/LTM Manuale del prodotto
Roger
Roger OSR88M-IO Manuale utente
Roger
Roger CPR32-SE v2.0 Manuale utente
Roger
Roger MCT86M-IO-CH-HR Manuale utente
Roger
Roger MCT80M Manuale utente
Roger
Roger PRT12MF-DES Manuale utente
Roger
Roger MCX2-BRD Manuale utente
Roger
Roger MCT82M-IO-CH Manuale utente
Roger
Roger MCI-2 Manuale utente
Roger
Roger MC16-PAC-2-KIT Manuale utente
Roger
Roger PRT32 Guida all'installazione
Roger
Roger B70/2DC Manuale del prodotto
Roger
Roger MCT82M-IO-HR Manuale utente
Roger
Roger RKD32 Manuale utente
Roger
Roger MC16-PAC-2-KIT Manuale utente
