Rowenta DZ9030 Manuale utente

SLO

www.rowenta.com

model DZ9030

COUV_DZ9000_14Langues 22/02/06 11:42 Page 1

10*

3a 3d3c3b

11a* 11c*

11d*

11b*

COUV_DZ9000_14Langues 22/02/06 11:42 Page 2

fig. 1 fig. 2

fig. 3

fig. 4 fig. 5 fig. 6

fig. 7 fig. 8

NONO OKOK

fig. 9

NONO OKOK

fig. 10 fig. 11

fig. 12

COUV_DZ9000_14Langues 22/02/06 11:42 Page 3

fig. 13 fig. 14

fig. 15

fig. 16 fig. 17 fig. 18

fig. 19

NONO

OKOK

fig. 20

COUV_DZ9000_14Langues 22/02/06 11:42 Page 4

Spray nozzle

Filling inlet

(with slide-button opening)

Variable steam control

Dry ironing

Smooth steam

High Pressure steam

Self Clean

Spray button

Shot of steam button

Auto-off indicator light*

Cord

Handle

Thermostat control light

Temperature control dial

LED display

Yellow LED

Green LED

Red LED

Auto-off LED

Water tank

Maximum water level

indicator

Microsteam400 soleplate

DESCRIPTION

SAFETY INSTRUCTIONS

This appliance complies with the technical rules and standards

for safety currently in force (Electromagnetic Compatibility,

Low Voltage, Environment).

The appliance may only be connected to alternating current as

specified on the rating plate. Only safe extension leads should

be used.

An electrical appliance is not a toy. Use and store the appliance out

of reach of children. Do not let the supply cord hang down.

Do not leave the appliance unattended while it is connected to the

mains supply.

Electrical appliances generate high temperatures. Always use the

handle and warn other users of the potential dangers (e.g. escaping

steam or hot water, especially when ironing vertically).

Never direct steam at persons or animals, never treat clothing

which is being worn.

Always disconnect the appliance before filling or emptying the

water tank; before leaving the room (even for a short time); before

cleaning the appliance and after use.

Never unplug the appliance by tugging on the cord.

Do not immerse the appliance in water.

An electrical appliance should not be used if:

– the appliance is not functioning correctly;

– the appliance, the supply cord or the cord protector is damaged;

– the appliance has been dropped;

* depending on model

DZ9000-11038999469 2/03/06 14:29 Page 3

– the appliance is obviously leaking. In these cases the appliance

should be returned to an approved Rowenta Customer Service

Centre for repair. (See enclosed Service Centre addresses.) Repairs

to electrical appliances may only be carried out by specialists.

Improperly carried out repairs can cause serious danger to users.

To avoid danger to users, a defective or damaged supply cord

may only be replaced by an authorised Rowenta Customers

Service Centre .

This product has been designed for domestic use only.

Any commercial use, inappropriate use or failure to comply

with the instructions, the manufacturer accepts no responsibility

and the guarantee will not apply.

Environment protection first !

Your appliance contains valuable materials which

can be recovered or recycled.

Leave it at a local civic waste collection point.

Keep these instructions

BEFORE USE

1 • Unpacking

Take the iron out of the box and remove all the stickers.

2 • What water may be used ?

Your iron has been designed to operate using untreated tap water

up to 17° dH (German water hardness) or 3 mmol/liter. However, if

your water is very hard, you can mix 50% untreated tap water with

50% distilled or demineralised water.

IMPORTANT Before doing anything else, remove the soleplate

protector (fig.1)!

IMPORTANT Heat concentrates the elements contained in

water during evaporation.The type of water listed below

DZ9000-11038999469 2/03/06 14:29 Page 4

3 • Using for the first time

Plug in the iron (fig.2) and set the temperature control dial (fig.3)

to ••• to heat the appliance.

A little smoke and a slight smell may be emitted, but this is only

temporary.

Unplug the iron (fig.4) and fill the water tank (§ 4 Filling the water

tank).

To remove any impurities in the iron's steam chamber, unplug the

iron and hold it over a sink horizontally. Push the steam control into

the Self Clean position : steam will now begin to build up. After a

few seconds water will emerge from the soleplate, rinsing any

impurities out of the steam chamber (fig.5).

Move the steam control to steam position after approx.

1 minute. Plug in the iron and allow the iron to heat up again.

Wait until the remaining water has evaporated. Unplug from the

mains and allow the iron to fully cool down.

contain organic waste or mineral elements that can cause

spitting, brown staining or premature wear of the appliance:

- water from clothes dryers, scented or softened water, water

from refrigerators, batteries or air conditioners, pure distilled

or demineralised water or rain water should not be used in

your iron. Also do not use boiled, filtered or bottled water.

USE

4 • Filling the water tank

Tilt the iron. Open the filling inlet (fig.6). Pour in water up to the

max mark (fig.7). Close the filler inlet (fig.8) and return the iron to

the horizontal.

5 • Setting the temperature

Set the iron temperature to suit the type of material using the

temperature control dial (fig.3).

IMPORTANT Before filling the water tank, unplug the iron and

set the steam control to dry position .

DZ9000-11038999469 2/03/06 14:29 Page 5

Temperature control*:The temperature control light indicates that

the soleplate is heating up. When the temperature control light goes

off (fig.9), the set temperature is reached and you can begin ironing.

Electronic temperature control*:The traffic lights tell you whether

the soleplate is at the selected temperature (fig.10).

6 • Dry ironing

Set the variable steam control to (fig.11) and set the

temperature to suit the type of material (care points •, ••, •••).

Ironing label Fabric Temperature

control

Synthetic fibres, e.g.

viscose, polyester…

•

Silk, wool

••

Cotton, linen

•••

YELLOW

(pulse)

The soleplate is still too cold for the selected material.

GREEN The soleplate is at the right temperature for the selected

material.

RED

(pulse)

The soleplate is still too hot for the selected material.

AUTO- OFF

(blinking)

The automatic electronic cut-out* is active.

TIP Always spray starch onto the reverse side of the fabric to

be ironed.

IMPORTANT The iron takes longer to cool down than to heat

up. We recommend that you start with fabrics to be ironed at

a low temperature. For mixed fabrics set the temperature for

the most delicate fabric.

* depending on model

DZ9000-11038999469 2/03/06 14:29 Page 6

7 • Steam ironing

You can steam iron from temperature setting •• up.The steam

quantity can be adjusted between Smooth Steam (soft steam

continuous diffusion) up to High Pressure steam .

We recommend setting to High Pressure steam only when the iron

is at temperature setting •••.

8 • High Pressure Steam

Your iron is fitted with the new High Pressure Steam system

(fig.13).This technology generates higher steam pressure to enable

the steam to penetrate much faster and further into the fabric.

This way you get excellent results from your ironing.

The steam is emitted in frequent bursts rather than continuously.

The pressure generated may cause a slight noise.This is not a

technical fault!

9 • Shot of Steam

(from temperature setting •• up)

Press the shot of steam button to generate a powerful jet of

steam and remove stubborn creases (fig.14).

10 • Vertical shot of steam

(from temperature setting •• up)

Hold the iron to the vertical and press the shot of steam button

(fig.15) to remove creases from suits, jackets, skirts, hanging

curtains etc.

11 • Spray

Press the spray button to dampen stubborn creases (fig.16).

12 • Anti-Drip system*

It prevents water escaping from the soleplate when the temperature

is too low.

IMPORTANT Leave an interval of 4 seconds between each

shot and wait until the flow of steam is finished before

standing the iron on its heel.

IMPORTANT Never direct the steam at persons or animals!

TIP Hold the iron 10 to 20 centimetres away from the garment

to avoid burning delicate fabrics.

* depending on model

DZ9000-11038999469 2/03/06 14:29 Page 7

13 • Automatic electronic 3-position shut off

If, although switched on, the appliance is not moved, it will

automatically switch off and the auto off light will blink after

the following intervals (fig.17):

- After 30 sec., if the iron is standing on the soleplate or lying on its side.

- After 8 mins., if the iron is standing on its heel.

AFTER USE

14 • Emptying

Unplug the iron (fig.4), pour away remaining water (fig.18) and set

steam control to .

Open and close the steam control several times (fig.19) to prevent

the drip hole into the steam chamber from furring or blocking up.

15 • Storing

Allow the appliance to cool down before storing the iron standing

on its heel

(fig.20)

MAINTENANCE AND CLEANING

16 • Anti-scale system

Your iron contains an anti-scale cartridge to reduce scale deposits.

This considerably prolongs the operational life of your iron.

The anti-scale cartridge is an integral part of the water tank and

does not need to be replaced.

17 • Self Clean function

(prolongs the life of the iron)

The Self Clean function flushes dirt and scale particles out of the

steam chamber. Fill the water tank with tap water up to the max

mark and heat the iron to the ••• temperature. Unplug the iron and

hold it over a sink horizontally. Hold the steam control into the Self

IMPORTANT Do not wind the cord around the hot soleplate.

Never store your iron placed down on the soleplate (fig.20).

IMPORTANT Unplug and allow the iron to fully cool down

before maintenance and cleaning.

IMPORTANT Do not use descaling agents, as these damage the

lining of the steam chamber and so may impair the steam function.

DZ9000-11038999469 2/03/06 14:29 Page 8

Indice

Altri manuali Rowenta Ferro

Rowenta

Rowenta DW7180 Manuale utente

Rowenta

Rowenta DW9080 Manuale utente

Rowenta

Rowenta Focus Excel DW83 Series Manuale utente

Rowenta

Rowenta DZ5 Manuale utente

Rowenta

Rowenta ACCESSTEAM DW23 Manuale utente

Rowenta

Rowenta DG5030 Manuale utente

Rowenta

Rowenta Freemove DE5020 Manuale utente

Rowenta

Rowenta DW9100 Manuale utente

Rowenta

Rowenta DG8560 Manuale utente

Rowenta

Rowenta DW5000 Manuale utente

Rowenta

Rowenta DW8000 Manuale utente

Rowenta

Rowenta Pressure iron & steamer Manuale utente

Rowenta

Rowenta IS9100D1 Manuale utente

Rowenta

Rowenta DW8100s Manuale utente

Rowenta

Rowenta PowerPress Manuale utente

Rowenta

Rowenta Compact Steam DG7550 Manuale utente

Rowenta

Rowenta DA1500 Manuale utente

Rowenta

Rowenta DW9220 Manuale utente

Rowenta

Rowenta DW8360 Manuale utente

Rowenta

Rowenta DW3185U5 Manuale utente

Rowenta

Rowenta STEAMCARE Manuale utente

Rowenta

Rowenta Master DW9055U1 Manuale utente

Rowenta

Rowenta PRO PERFECT DG88 Series Manuale utente

Rowenta

Rowenta DW2000 Manuale utente

Manuali Ferro popolari di altre marche

Clatronic

Clatronic DB 3703 Manuale utente

TEFAL

TEFAL FV4093Z0 Manuale utente

Gorenje

Gorenje SIH 2200 BS Manuale utente

Philips

Philips GC6012 Manuale utente

Bosch

Bosch 2 Series Manuale utente

Riffel

Riffel Catena KB-819 Manuale utente

Texi

Texi Hestia Manuale utente

Maxwell

Maxwell MW-3010 Manuale utente

TREVIDEA

TREVIDEA Girmi ST60 Manuale utente

Philips

Philips HI5914/30 Manuale utente

Primula

Primula Vapormat Manuale utente

Magio

Magio MG-541 Manuale utente

Scarlett

Scarlett SC-1334S Manuale utente

Bosch

Bosch Sensixx B22L Manuale utente

Philips

Philips GC651 Manuale utente

Vitek

Vitek VT-1247 VT Manuale utente

Cleanmaxx

Cleanmaxx 3397 Manuale utente

Philips

Philips GC800 Manuale utente