Runxin 53520 Manuale utente

Page | 1

Runxin 53520 Filter Valve

Instruction Manual

Page | 2

Table of Contents

Installation Summary Page 3

General Specifications Page 4

Installation Page 5

Service cycles Page 6

Parameter Settings Page 7

Valve Breakdown Page 8

Circuit Board Functions Page 9

Valve Settings Page 10-11

Flow Rate Curve Page 12

Trouble Shooting Page 13-14

Page | 3

Installation Summary

Installation Location: Installation Date:

Installed by: Phone:

Application Type:

Water Source:

Water Test Results

Hardness: Iron: pH:

Other:

Misc:

Tank Size:

Diameter Height:

Resin or Media Type:

Resin or Media Volume: Brine tank Size:

Capacity:

Service Flow Rate:

Min: Max: Backwash:

Inlet Pressure: KPa

Control Valve Configuration

Valve Type: Valve Part No.

Serial Number:

Regenerant Refill Control: Gpm/lpm Injector Type: Gpm/lpm

Drain line flow control: Gpm/lpm

Page | 4

General Specifications

Operating

Minimum/Maximum operating pressures: 20psi (138kPa) –87psi (600kPa)

Minimum/Maximum Operating Temperature: 5°C -50°C

Power Supply: 240V/50Hz DC24V 1.5A

Connections

Inlet: 2” Male BSP

Outlet: 2” Male BSP

Waste: 2” Male BSP

Riser Pipe: 2” D-GB (63mm OD)

Tank Thread: 4”-8UN

Page | 5

Installation

Before Installation, read instructions thoroughly. The installation of the system should be completed

by a professional.

36x72” GS1000 High Absorption micro pollutants, Carbon Media Loading:

160kg 3-6mm #5 Underbed Gravel (Load in tank first)

80kg 8/16 #6 Underbed Gravel (Load in tank second)

210kg GS1000 (8x30) Carbon (Load in tank last)

342LPM Backwash Flow control supplied with valve

Use filling funnel provided:

Do not use Vaseline, oils, or Spray silicone on valve O-rings. 100% Silicone Lubricant must be used

for the O-rings

Locate the system as close as possible to the nearest drain.

The cylinder should be situated on a firm, level surface.

The system should be kept away from boilers, heater and installed inside.

Allow adequate space for pipework and removal of the valve when it is due for servicing equipment.

All pipework should be done in accordance with local plumbing regulation and codes.

Do not use the valve as a support mechanism for pipework use correct supports.

It is recommended to install bypass for the system, to allow for works to be performed on the valve

or cylinder without interruption to production. (Figure 1)

If the installer is soldering pipework, it is important no pipework is connected to the valve as the

heat will damage the system.

When using Teflon tape be careful not to cross thread the fittings.

Allow an air gap when plumbing the waste line to drain.

Page | 6

Riser pipe should be cut off flush with the top of the cylinder and deburred.

Centre the riser in the cylinder and plug to not allow any media to enter riser when filling the

cylinder, fill the media as per suppliers’ recommendations.

Remove plug and fill system slowly with water

Once cylinder is 90% full of water install the valve, making sure not to cross thread the valve.

Connect inlet, outlet and drain line to the valve.

Turn on power to the valve and check system settings are correct

Put system into back wash and then slowly open the inlet valve to allow for air to be removed from

the system.

Once air has been removed and a constant flow of water is running down the backwash line, open

the inlet fully until all fines from the media has flushed out of the system. (This may require 2-3

backwashes)

After backwash make sure to put the valve into flush to settle the media bed.

After backwash is complete check for any leaks within the system and pipework.

Fig.1

Page | 7

System Status

Service Status: Unfiltered water is directed through the media bed and up through the distributor

and riser pipe.

Backwash Status: The flow of water is redirected down the riser and up through the media bed.

lifting the media and removing the sediment down the waste line.

Fast Rinse Status: The Flow of water is directed through the media bed and up through the

distributor and riser pipe and sent to drain. This is to allow the media bed to resettle and remove

any sediment that may be left in the pipework from the backwash.

Page | 8

Display Icons Runxin Controller

Parameter Specifications

Page | 9

Valve Breakdown

Page | 10

Signal Output

There is a signal output connector on the circuit board. It is for controlling

external wiring (Refer to Figure 2 and Figure 3).

There are two kinds of output modes.

b-01: Sends signal start of backwash and stops sending signal at end of

rinse cycle

b-02: Sends signal in between cycles

Interlock Function

The circuit board has an interlock function to send a signal between Runxin

valves in a parallel set up. When one of the units has started a backwash, the

signal will be sent to the other valve and lock it out from performing a

backwash until the first valve has completed its cycles.

Indice

Altri manuali Runxin Unità di controllo

Runxin

Runxin 51240B (F112BS) Manuale utente

Runxin

Runxin 53515 Manuale utente

Runxin

Runxin 55504 Manuale utente

Runxin

Runxin 63504 Manuale utente

Runxin

Runxin 63510 Manuale utente

Runxin

Runxin 63518 Manuale utente

Runxin

Runxin 63504 Manuale utente

Runxin

Runxin F79A-LCD Manuale utente

Runxin

Runxin 51215 Manuale utente

Runxin

Runxin F139 Manuale utente

Runxin

Runxin F71B1 Manuale utente

Runxin

Runxin N74Q1 Manuale utente

Runxin

Runxin F56A Manuale utente

Runxin

Runxin F104 A Manuale utente

Runxin

Runxin 17603 Manuale utente

Runxin

Runxin 73605 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente