Sapling 3100 series Manuale utente

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Installation Manual V1.1

SBW Series Wi-Fi Clock

Current as of February 2017

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

SBW Series Wi-Fi Clocks

Table of Contents

Table of Contents 2

Important Safety Instructions 3

Identify Your Clock 4

Preparing to Install - System/Network Requirements 5

Synchronization System Setup 6 - 7

Configure multiple clocks with wifiDirectLoader 8 - 9

Wall Mount Installation 10 - 15

Flag Mount Installation 16 - 23

Double Mount Installation 24 - 30

Connecting to the Clock 31

Adjustable Jumper Settings 32

Temperature Sensor Installation 33

IP Monitor Software - Main Screen 34

- Task Bar Options 35 - 38

I - Quick Access Menu 39

- Error Messages 40

Web Interface

- Log In 41

- Home Page 41

- Network Settings 42-43

- General Settings 44

- Time Settings 45

- Daylight Saving Time 46

- Servers 47

- Display Settings 48

Manuals may change without prior notice

VERY IM PORTANT:

CONFIGURE YOUR CLOCK BEFORE MOUNTING IT TO A WALL

OR HOUSING. REFER TO THE SYNCHRONIZATION SYSTEM SETUP

SECTION OF THIS MANUAL FOR INSTRUCTIONS.

A Sapling Master Clock and any Repeaters must be properly

installed, powered, and set up BEFORE you attempt to set up a

wireless clock system. If the Master Clock and Repeaters are not

powered, the secondary clocks will not synchronize.

- Elapsed Timer 49

-Login Settings 50

- Diagnostics 51

-Troubleshooting 52

- Software Update 53

Manual Controls 54

Frequently Asked Questions 55

Troubleshooting 56 - 57

Warranty 58

FCC Statement 59

Available with 3200 model only

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Important Safety Instructions

DANGER

SHOCK HAZARD

• Keep the electricity to this device

turned OFF until the clock installation

is complete.

• Do not expose the clock circuits to

water, or install the clock in a location

where it may be exposed to water.

WARNING

FIRE HAZARD

• Always follow your national and

regional electrical codes or ordinances.

• The AC power circuit for the clock

must be attached to a circuit breaker that

can be reset by the user.

PHYSICAL INJURY HAZARD

• If you are standing on an object while

installing your clock, make sure that the

object can support your weight, and will

not sway or move as you stand on it.

• Take precautions to avoid injury by

potential safety hazards near the point

of installation including (but not limited

to) heavy machinery, sharp objects, hot

surfaces, or exposed cables carrying an

electric current.

• Follow all mounting instructions exactly

as stated in this manual. Failure to do so

may result in the device falling off the

point of installation.

• Packaging materials and mounting

items include plastic bags and small

pieces, which pose a suffocation hazard

to young children.

NOTICE

• Do not install the clock outdoors.

Damage to the clock if placed outdoors

voids the warranty.

• Do not hang objects from the clock or

clock mounting parts. The clocks are not

designed to support the weight of other

objects.

• The clock face and housing may

be cleaned with a damp cloth or

disinfectant. Test other cleaning products

on a small part of the clock housing

before attempting to use on the rest of

the clock. Avoid bleach and chemicals

known to dissolve plastics.

! !

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Identify Your Clock

A label containing the part number of your clock is attached to the clock packaging

If your part number begins with SBW-31, you own a 3100 Series clock

If your part number begins with SBW-32, you own a 3200 clock

If your part number begins with SBW-33 you own a 3300 clock*

If the second group in your part number ends in S (31S, 32S, 33S), you own a Surface Mount Clock,

which can be attached to a pole as a Flag Mount or a Double Mount.

If you wish to change the mounting type, contact your dealer.

*THIS MANUAL COVERS 3100 and 3200 MODELS ONLY. If you have a SBW 3300

clock, check the manuals section on sapling-inc.com for an updated version of

this manual.

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

To be able to set up an IP-based synchronized clock network, you will need the following items:

• This manual

• A Wireless Local Area Network (WLAN) that has access to at least one of the following:

• An in-house NTP server

• The Internet

• A ﬁrewall that is open on Ports 80, 123, and 1777

• At least one laptop or desktop computer with access to the following:

• The same LAN as the clocks

• The same subnet as the clocks

• A web browser such as Internet Explorer, Microsoft Edge, or Mozilla Firefox.

• An internal or external Wi-Fi network card.

• A wireless router or wireless access point for the LAN that operates on the subnet 192.168.0.##, and

broadcasts using an 802.11 b/g/n protocol.

• Depending on the size of the network, you may need to install additional Wireless Access Points.

• A copy of the monitor.exe program.

• Security access to all of the above items.

• A means of keeping a record of the clock serial numbers, locations, and IP addresses. Create a table like

the one shown below:

SERIAL # LOCATION IP ADDRESS

Preparing to Install - System/Network Requirements

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Positioning the Wireless Router or Wireless Access Point (WAP):

The main router or WAP should be installed in a central location. Depending on the transmission protocol

of your router, the clocks must be located within the following ranges:

Wi-Fi Protocol Range (Feet) Range (Meters)

8 02.11 b 115 fe et 35 meters

8 02.11 g 125 feet 38 meters

8 02.11 n 230 feet 70 meters.

Check with the access point or router manufacturer, as some transmitters offer boosted ranges.

*NOTE: This clock is not compatible with 802.11a or 802.11ac protocols. Many AC-compatible routers and

access points are backwards compatible with 802.11n. Check your router settings for more information.

Be aware of walls or other obstructions made of thick concrete or sheet metal, as these may block the

signal entirely.

Logging into the SBW for the ﬁrst time:

1.Power the clock. Press and release the Top Button on the front panel twice.

2.On a Wi-Fi enabled computer, check the available Wireless Networks. Refresh the available networks

until a network named SAPLING DIGITAL-#### appears (where #### is the serial number of the clock).

This may take up to 30 seconds. Once it appears, connect to this network.

3.Open a web browser and enter the following web address into the URL ﬁeld:

192.168.240.1/login.html

4.On the login page, use the password 6063 to log into the clock.

5.Click on the Network Settings button.

Synchronization System Setup

Top Button

Bottom Button

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Synchronization System Setup (ctd.)

6. In the Network ﬁeld, enter the SSID of your preferred Wi-Fi network. This is the name that appears if you try

to connect to that Wi-Fi network on any other computer, tablet, or smart phone. If you do not remember the

name of your network, check to see if it has appeared in the Select Network list.

7. In the Network Password ﬁeld, enter the password of your preferred Wi-Fi network. Network passwords

must be twenty-six characters or fewer.

8. If you wish to set a static IP address, change DHCP Auto On from ON to OFF, then enter information for

the Static IP address, Subnet Mask, and Gateway Address. To acquire this information, contact your network

administrator.

9. If you wish to set a DNS server other than the one provided through DHCP, change Auto DNS from ON to

OFF, then enter an IP address for a new DNS server in the DNS Address ﬁeld.

10. Press the Submit button, followed by the Log Out button.

11. The clock should connect to the new Wi-Fi network. Conﬁrm by accessing the clock with the Wi-Fi Monitor

(If clock DHCP is on and the computer is on the same subnet as the Access Point) or the new static IP address (if

clock DHCP is off). If the clock is not accessible, press the WiFi SW button once and wait thirty seconds before

trying to access the clock with the Wi-Fi Monitor or IP address. If the clock is still not accessible, refer to the

section of this manual labeled “Troubleshooting”

For battery powered clocks: For the ﬁrst ten minutes after powering on a new (or recently reset-to-default) clock

will be accessible once every minute. Once the user has entered and saved new network settings, the clock will

only connect to the network once to make initial contact, then it will not access the network again until the next

synchronization period four hours later. To force the clock to power its transmitter, the user must press the WiFi SW

button.

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Conﬁguring multiple clocks with wiﬁDirectLoader

wiﬁDirectLoader.exe is a piece of software that lets a user rapidly duplicate existing clock settings to other

clocks of the same type (analog or digital). This is useful for large clock systems, where a user may not

have the time to conﬁgure many clocks individually.

NOTICE: Starting wiﬁDirectLoader.exe will take your computer off of its current Wi-Fi network.

If you need to access your network while simultaneously running this software, connect the

computer to the network using a LAN cable.

Obtaining the conﬁguration ﬁle:

1) DO NOT Start wiﬁDirectLoader.exe. First, set up one clock using the steps described in the

Syncronization Setup section of this manual.

2) Once you have completed all the steps, exit the clock.

3) Start wiﬁDirectLoader.exe by double-clicking on it.. Enter the value

6063 in the password ﬁeld.

4) Power the clock. Press and release the Top

Button on the front panel twice.

5) in the wiﬁDirectLoader.exe window, an entry

should appear for the clock.

6) Click on the entry name for the clock, then press

on the Upload from Selected Clock button.

7) Save the conﬁguration ﬁle to an easily-accessible location, like your My Documents or Desktop folder.

Top Button

Bottom Button

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Conﬁguring multiple clocks with wiﬁDirectLoader

Before Applying the conﬁguration ﬁle:

The fastest way to perform this process is to collect all of the Wi-Fi clocks in a single room and run this

program.

If you have already installed the Wi-Fi clocks on the wall, you will need to take each clock down to access

the Direct Mode button. Since Wi-Fi has a limited broadcast range, you will need to take a mobile, Wi-Fi-

capable computer such as a laptop or ultrabook that runs wiﬁDirectLoader while you go to each clock.

Applying the conﬁguration ﬁle:

1) Press on the Select Conﬁguration ﬁle button. Use

the window to select the conﬁguration ﬁle that you

downloaded from the ﬁrst clock. If you cannot see the

ﬁle, conﬁrm that the Types of File ﬁeld is set to Digital

WiFi (*.dwiﬁ).

2) Under the Options menu, select Auto Run.

3) Power additional clocks and place them into direct mode using Step 4 from the previous page.

4) wiﬁDirectLoader.exe will automatically program every clock that appears. Clocks can be identiﬁed by

their Serial Number, which will appear as part of the name of each clock that appears in the ﬁeld to the

right of the buttons.

5) Once each clock is programmed, the clock may be powered down, then mounted on the wall using

the instructions in the following sections.

6) Once all clocks are programmed, exit out of wiﬁDirectLoader. You will be unable to access any other

networks if wiﬁDirectLoader is still running.

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Wall Mount Installation

Included in Package

Description

SBW Digital Clock

Digital Clock Wall Housing

6-19x1/2 screw

6-32x1 screw

Quantity

Picture

PLEASE NOTE: A user will also have to provide a Phillips-head screwdriver, a small ﬂat-blade screwdriver, a double gang box, any equipment needed to

install the gang box, and any additional wiring needed to extend the signal, power, or ground cables. You may also need a 1/4 inch drill, 4 #8x1.5 self-

tapping screws, and 4 wall anchors for those screws if you decide not to attach the clock directly to the gang box.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a

replacement kit.

Included in Wiring Kit (D-PK-3-110-S or D-PK-3-24-S)

Power/grounding wires

and connector

1or

110V 24V

VERY IMPORTANT:

CONFIGURE YOUR CLOCK BEFORE MOUNTING IT TO A WALL OR HOUSING. REFER TO THE

SYNCHRONIZATION SYSTEM SETUP SECTION OF THIS MANUAL FOR INSTRUCTIONS.

All network equipment must be powered and conﬁgured before you install the clock. If the network equipment is not properly installed and

powered, and if the clocks have not been conﬁgured to communicate with the network equipment, the secondary clocks will not synchronize.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Sapling Orologio

Sapling

Sapling SBP Series Manuale utente

Sapling

Sapling NTP 8000 Series Manuale utente

Sapling

Sapling SMC 3000 Series Manuale utente

Sapling

Sapling SAL Series Manuale utente

Sapling

Sapling SSM Series Manuale utente

Sapling

Sapling SMA 6000 Series Manuale utente

Sapling

Sapling SAP Series Manuale utente

Sapling

Sapling SAL-2 Series Manuale utente

Sapling

Sapling SAI Series Manuale utente

Sapling

Sapling SDLG Series Manuale utente

Sapling

Sapling SBL Series Manuale utente

Sapling

Sapling SAL-2 Series Manuale utente

Sapling

Sapling SLD Premium Series Manuale utente

Sapling

Sapling SMA 2000 Series Manuale utente

Sapling

Sapling Saw 4 Manuale utente

Sapling

Sapling SBD Series Manuale utente

Sapling

Sapling SALG Series Manuale utente

Sapling

Sapling Prayer Clock Manuale utente

Sapling

Sapling NTP 7000 Series Manuale utente

Sapling

Sapling SBD 1000 Series Manuale utente

Sapling

Sapling SMA 2000 Series Manuale utente

Sapling

Sapling SBD 3000 Series Istruzioni per il montaggio

Sapling

Sapling SBP-31 Manuale utente

Sapling

Sapling SBP 3000 Series Istruzioni per il montaggio

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente