Sapling Saw 4 Manuale utente

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Current as of January 2017

SAW Series Wi-Fi Clock

Installation Manual V1.0.2

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

SAW Series Wi-Fi Clocks

Table of Contents

Table of Contents 2

Important Safety Instructions 3

Identify Your Clock 4

Preparing to Install - System/Network Requirements 5

Synchronization System Setup 6 - 7

Wall Mount Installation -

- Round SlimLine Clock - Battery Powered 8 - 10

- Locally Powered 11 - 14

- Round Aluminum/Wood Clock - Battery Powered 15 - 18

- Locally Powered 19 - 23

- Square Clock - Battery Powered 24 - 27

- Locally Powered 28 - 31

Flag Mount Installation -

- Round SlimLine/Aluminum Clock - Battery Powered 32 - 38

- Locally Powered 39 - 45

- Square Clock - Battery Powered 46 - 52

- Locally Powered 53 - 59

Double Mount Installation -

- Round SlimLine/Aluminum Clock - Battery Powered 60 - 65

- Locally Powered 66 - 71

- Square Clock - Battery Powered 72 - 78

- Locally Powered 79 - 85

Connecting to the Clock 86

IP Monitor Software - Main Screen 87

- Task Bar Options 88 - 91

I - Quick Access Menu 92

- Error Messages 93

Manuals may change without prior notice

VERY IM PORTANT:

CONFIGURE YOUR CLOCK BEFORE MOUNTING IT TO A WALL

OR HOUSING. REFER TO THE SYNCHRONIZATION SYSTEM SETUP

SECTION OF THIS MANUAL FOR INSTRUCTIONS.

A Sapling Master Clock and any Repeaters must be properly

installed, powered, and set up BEFORE you attempt to set up a

wireless clock system. If the Master Clock and Repeaters are not

powered, the clocks will not synchronize.

Web Interface

- Log In 93

- Home Page 93

- Network Settings 94 - 95

- General Settings 96

- Time Settings 97

- Daylight Saving Time 98

- Servers 99

-Login Settings 100

- Diagnostics 101

-Troubleshooting 102

- Software Update 103

Frequently Asked Questions 104 - 105

Troubleshooting 106 - 108

Diagnostic #1 - Signal Information 109

Diagnostic #2 - Battery Voltage 110

Diagnostic #3 - Full Mechanical Test 110 - 111

Restore Clock to Manufacturing Default 111

Warranty 112

FCC Statement 113

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Important Safety Instructions

DANGER

SHOCK HAZARD

• Keep the electricity to this device

turned OFF until the clock installation

is complete.

• Do not expose the clock movement to

water, or install the clock in a location

where it may be exposed to water.

WARNING

FIRE HAZARD

• Always follow your national and

regional electrical codes or ordinances.

• The AC power circuit for the clock

must be attached to a circuit breaker that

can be reset by the user.

PHYSICAL INJURY HAZARD

• If you are standing on an object while

installing your clock, make sure that the

object can support your weight, and will

not sway or move as you stand on it.

• Take precautions to avoid injury by

potential safety hazards near the point

of installation including (but not limited

to) heavy machinery, sharp objects, hot

surfaces, or exposed cables carrying an

electric current.

• Follow all mounting instructions exactly

as stated in this manual. Failure to do so

may result in the device falling off the

point of installation.

• Packaging materials and mounting

items include plastic bags and small

pieces, which pose a suffocation hazard

to young children.

NOTICE

• Do not install the clock outdoors.

Damage to the clock if placed outdoors

voids the warranty.

• Do not hang objects from the clock or

clock mounting parts. The clocks are not

designed to support the weight of other

objects.

• The clock face and housing may

be cleaned with a damp cloth or

disinfectant. Test other cleaning products

on a small part of the clock housing

before attempting to use on the rest of

the clock. Avoid bleach and chemicals

known to dissolve plastics.

! !

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Identify Your Clock

A label containing the part number of your clock is attached to the

clock movement.

If your part number begins with SAW-4, you own a SlimLine ABS or SQUARE clock

If your part number begins with SAW-5, you own an ALUMINUM clock

If your part number begins with SAW-6, you own a WOOD clock

Example part numbers:

SAW-4BS-12S-4 (SQUARE clock)

SAW-4BS-12R-4 (SlimLine ABS clock)

SAW-5AS-09R-1 (ALUMINUM clock)

SAW-6DS-12R-2 (WOOD clock)

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

To be able to set up an IP-based synchronized clock network, you will need the

following items:

• This manual

• A Wireless Local Area Network (WLAN) that has access to at least one of the following:

• An in-house NTP server

• The Internet

• A ﬁrewall that is open on Ports 80, 123, and 1777

• At least one laptop or desktop computer with access to the following:

• The same LAN as the clocks

• The same subnet as the clocks

• A web browser such as Internet Explorer, Microsoft Edge, or Mozilla Firefox.

• An internal or external Wi-Fi network card.

• A wireless router or wireless access point for the LAN that operates on the subnet

192.168.0.##, and broadcasts using an 802.11 b/g/n protocol.

• Depending on the size of the network, you may need to install additional Wireless

Access Points.

• A copy of the monitor.exe program.

• Security access to all of the above items.

• A means of keeping a record of the clock serial numbers, locations, and IP addresses.

Create a table like the one shown below:

SERIAL # LOCATION IP ADDRESS

Preparing to Install - System/Network Requirements

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Positioning the Wireless Router or Wireless Access Point (WAP):

The main router or WAP should be installed in a central location. Depending on the transmission protocol

of your router, the clocks must be located within the following ranges:

Wi-Fi Protocol Range (Feet) Range (Meters)

8 02.11 b 115 feet 35 meters

8 02.11 g 125 feet 38 meters

8 02.11 n 230 feet 70 meters.

Check with the access point or router manufacturer, as some transmitters offer boosted ranges.

*NOTE: This clock is not compatible with 802.11a or 802.11ac protocols. Many AC-compatible routers and

access points are backwards compatible with 802.11n. Check your router settings for more information.

Be aware of walls or other obstructions made of thick concrete

or sheet metal, as these may block the signal entirely.

Logging into the SAW for the ﬁrst time:

1. Power the clock. Press and release the right-side “WIFI

SW” on the movement twice. The Yellow and Orange LEDs

will light up for a few seconds, and then the Yellow LED will

become brighter.

2. On a Wi-Fi enabled computer, check the available Wireless

Networks. Refresh the available networks until a network

named CLOCK_#### appears (where #### is the serial number of the clock). This may take up to 30

seconds. Once it appears, connect to this network.

3. Open a web browser and enter the following web address into the URL ﬁeld:

http://192.168.240.1/login.html

4. On the login page, use the password 6063 to log into the clock.

5. Click on the Network Settings button.

Synchronization System Setup

MECH SW WIFI SW

Yellow Orange

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Synchronization System Setup (ctd.)

6. In the Network ﬁeld, enter the SSID of your preferred Wi-Fi network. This is the name that appears

if you try to connect to that Wi-Fi network on any other computer, tablet, or smart phone.

7. In the Network Password ﬁeld, enter the password of your preferred Wi-Fi network. Network

passwords must be twenty-six characters or fewer.

8. If you wish to set a static IP address, change DHCP Auto On from ON to OFF, then enter information

for the Static IP address, Subnet Mask, and Gateway Address. To acquire this information, contact your

network administrator.

9. If you wish to set a DNS server other than the one provided through DHCP, change Auto DNS from

ON to OFF, then enter an IP address for a new DNS server in the DNS Address ﬁeld.

10. Press the Submit button, followed by the Log Out button.

11. The clock should connect to the new Wi-Fi network. Conﬁrm by accessing the clock with the IP

Monitor (If clock DHCP is on and the computer is on the same subnet as the Access Point) or the new

static IP address (if clock DHCP is off). If the clock is not accessible, press the WiFi SW button once and

wait thirty seconds before trying to access the clock with the IP monitor or IP address. If the clock is still

not accessible, refer to the section of this manual labeled “Troubleshooting”

For battery powered clocks: For the ﬁrst ten minutes after powering on a new (or recently reset-to-

default) clock will be accessible once every minute. Once the user has entered and saved new network

settings, the clock will only connect to the network once to make initial contact, then it will not access

the network again until the next synchronization period four hours later. To force the clock to power its

transmitter, the user must press the WiFI SW button.

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Wall Mount Installation - Round SlimLine Clock - Battery Powered

Included in Package

Included in Wiring Kit (A-SLM-MK-S-1)

Description

SAW round SlimLine

analog clock

Quantity

Picture

Mounting Piece

#6-19x7/16 screw

Strain Relief

2 (not used)

1 (not used)

PLEASE NOTE: A user will also have to provide two D-Cell batteries, a Phillips-head screwdriver, a small slot-head screwdriver, a drill with a 1/4 inch drill bit,

a pencil, a single gang box, and any equipment needed to install the gang box.

If any of the items listed in the wiring kit are missing, you may contact your dealer and order a

replacement kit.

Included in Wiring Kit (A-WK-MTG-1)

#10x1.5 Self-tapping screw

Wall anchor

VERY IMPORTANT:

CONFIGURE YOUR CLOCK BEFORE MOUNTING IT TO A WALL OR HOUSING. REFER TO THE

SYNCHRONIZATION SYSTEM SETUP SECTION OF THIS MANUAL FOR INSTRUCTIONS.

The Clock and all network equipment must be powered and conﬁgured before you install the clock. If the network equipment is not

properly installed and powered, and if the clocks have not been conﬁgured to communicate with the network equipment, the clocks will not

synchronize.

Included in Gang Box Kit (A-GB-MK-1)

#6-32x1 screw

#6-19x3/8 screw

2 (not used)

1 (not used)

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

3) Insert the wall anchors into the two holes, then

place the two self tapping screws through the

mounting piece and into the wall anchors.

Wall Mount Installation - Round SlimLine Clock - Battery Powered

1) Place the mounting piece on the wall. Leave at

least 4 inches between the top of the gang box and

ceiling. Conﬁrm that the bottom of the mounting

piece is level with the ﬂoor.

4) Remove the back cover from the battery pack

by pulling the two latches away to either side and

sliding the cover out.

2) Use a pencil to mark the positions of the top two

holes, then use the 1/4 inch drill bit to drill holes at

the locations of the two marks.

4” Minimum

The Sapling Company, Inc.

1633 Republic Road

Huntingdon Valley, PA 19006

USA

P. (+1) 215.322.6063

F. (+1) 215.322.8498

www.sapling-inc.com

Wall Mount Installation - Round SlimLine Clock - Battery Powered

8) If you need to take the clock off the wall after

the installation has been completed, use a ﬂat-blade

screwdriver or eyeglasses screwdriver to lower the

mounting piece latch, then slide the clock off the

mounting piece.

5) First remove the gearbox pin, then insert the

batteries into the clock.

6) Place the cover back onto the battery pack. You

should hear a snapping noise as the latches engage.

7) Attach the clock to the mounting piece by sliding

the clock back onto it. You should hear a snapping

noise as the latch engages.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Sapling Orologio

Sapling

Sapling SBD 3000 Series Istruzioni per il montaggio

Sapling

Sapling SMC 3000 Series Manuale utente

Sapling

Sapling SBP 3000 Series Istruzioni per il montaggio

Sapling

Sapling SSM Series Manuale utente

Sapling

Sapling SMC 3000 Series Manuale del proprietario

Sapling

Sapling SMA 2000 Series Manuale utente

Sapling

Sapling SMA 2000 Series Manuale utente

Sapling

Sapling SBD 1000 Series Manuale utente

Sapling

Sapling SDLG Series Manuale utente

Sapling

Sapling SBL Series Manuale utente

Sapling

Sapling SALG Series Manuale utente

Sapling

Sapling 3100 series Manuale utente

Sapling

Sapling SBP Series Manuale utente

Sapling

Sapling SAI Series Manuale utente

Sapling

Sapling SBD Series Manuale utente

Sapling

Sapling SAL-2 Series Manuale utente

Sapling

Sapling SBT Series Manuale utente

Sapling

Sapling SAP Series Manuale utente

Sapling

Sapling SLD Premium Series Manuale utente

Sapling

Sapling NTP 8000 Series Manuale utente

Sapling

Sapling SBT 3000 Series Istruzioni per il montaggio

Sapling

Sapling SMA 6000 Series Manuale utente

Sapling

Sapling SAM Series Manuale utente

Sapling

Sapling SAL Series Manuale utente

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente