Satel INT-SF Manuale utente
INT-SF
Partition keypad int-sf_sii_en 07/20
Quick installation guide
Full manual is available on www.satel.eu
The device should be installed by qualified personnel.
Before installation, please read the full manual thoroughly.
Disconnect power before making any electrical connections.
The keypad is designed for indoor installation. The place of installation should be readily
accessible to the system users.
1. Open the keypad enclosure (Fig. 1). The enclosure opening tool, shown in the illustration,
is included in the keypad delivery set.
2. Set the partition keypad address (see “Address setting”).
3. Run the wires through the opening in the enclosure base.
4. Using wall plugs (anchors) and screws, fasten the enclosure base to the wall. Select wall
plugs specifically intended for the mounting surface (different for concrete or brick wall,
different for drywall, etc.).
5. Connect the CLK, DTA and COM terminals to the appropriate terminals of the control
panel expander bus (see the control panel installer manual).
2 INT-SF SATEL
6. If the partition keypad is to control an electric strike, electromagnetic lock or another door
actuator, connect this device to the NO terminals as shown in Fig. 2. It is not
recommended that the door actuator be powered from the same source as the partition
keypad.
7. If the keypad is to supervise the door status, connect the detector supervising the door
status to the IN and COM terminals. If the keypad is not to supervise the door status,
connect the IN terminal to the COM terminal or, when configuring the keypad, set value 0
for the “Max. door open time” parameter.
8. Connect the power wires to the 12V and COM terminals. The keypad may be powered
directly from the control panel, from an expander with power supply or from a power
supply.
9. Close the enclosure and then lock it with the screw.
10.Power on the alarm system.
11.Start the identification function in the control panel (see the control panel installer
manual). The keypad will be identified as "INT-S/SK".
Address setting
To set the address, use the DIP switches on the electronics board. The switches have
numbers assigned to them. The number for OFF position is 0. The numbers assigned to the
switches in ON position are presented in the table below. The sum of these numbers is the
address set.
Switch (ON position)
1 2 3 4 5
Number
1
2
4
8
16
The declaration of conformity may be consulted at www.satel.eu/ce
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. +48 58 320 94 00
www.satel.eu
Altri manuali per INT-SF
2
Indice
Altri manuali Satel Tastiera
Satel
Satel INT-KWRL2 Manuale utente
Satel
Satel INT-SF Manuale utente
Satel
Satel INT-TSH Manuale utente
Satel
Satel INT-KSG Guida utente
Satel
Satel ABAX 2 Manuale utente
Satel
Satel PERFECTA Manuale utente
Satel
Satel INT-KSG Manuale di istruzioni
Satel
Satel INT-TSG Manuale utente
Satel
Satel VERSA-LCDM-WRL Manuale utente
Satel
Satel PRF-LCD-WRL Manuale utente
Satel
Satel CA-6 KLED Manuale utente
Satel
Satel MKP-300 Manuale utente
Satel
Satel INT-S Series Manuale utente
Satel
Satel INT-S-GR Manuale utente
Satel
Satel INT-TSG Guida utente
Satel
Satel INT-SF Manuale utente
Satel
Satel INT-SCR Manuale utente
Satel
Satel CR-MF5 Manuale utente
Satel
Satel INT-SK Manuale utente
Satel
Satel VERSA INT-TSH2 Guida utente
