SC&T IP09CK Manuale utente
Smart Cabling & Transmission Corp.
V1.0_
191128M
IP/ PoE Extender
User Manual
Model : IP09CK
Ethernet over Coaxial Extender
1
User Manual
IP09CK
Introduction
IP09C is an IP extender that can use a single coaxial cable to send TCP/IP signal to a remote IP-enabled
device, with transmission distance up to 800M and bandwidth up to 100Mbps. Furthermore, since IP09C
can send IP signal over a coaxial cable, you can change your old analog cameras to IP ones without
replacing existing cables, which saves a plenty of labor and cost.
Features
Sends IP signal over coaxial cable.
Signal extension up to 800M over a RG59/6U coaxial cable
Bandwidth up to 70Mbps.
Able to send multiple IP signals over single Ethernet cable
Transmission Distance Chart
The transmission distance test report below is by means of using the COMMSCOPE 57535-2 (CAT5e
24AWG) cables and 75ΩRG59 or RG6U coaxial cables.
Port / Cable
Mode and Data Rate
Distance
RJ45 - CAT.5e
100BASE-TX with EEE 100Mbps
100M
RJ45 - CAT.5e
100BASE-TX 100Mbps
130M
RJ45 - CAT.5e
100BASE-T1 100Mbps
300M
RJ45 - CAT.5e
Long Reach 100Mbps
500M
RJ45 - CAT.5e
10BASE-T with EEE 10Mbps
100M
RJ45 - CAT.5e
10BASE-T 10Mbps
250M
RJ45 - CAT.5e
Long Reach 10Mbps
800M
BNC - RG59 (75-3)
100Mbps
300M
BNC - RG6U (75-5)
100Mbps
500M
BNC - RG59 (75-3)
10Mbps
800M
BNC - RG6U (75-5)
10Mbps
1000M
2
User Manual
IP09CK
I
Installation view
1) Point to Point Transmission
(2) Extra Long Extension by connecting with IP09
(3)Long Distance for Multiple cameras transmission
3
User Manual
IP09CK
Panel Review
No.
Interface
Function
1
RJ45 Connector
Port 1；To connect networking devices or another IP09
(Refer to Description 1,2,3)
2
BNC Connector
Port 2；To connect the other endpoint of IP09C
(Refer to Description 1,2)
3
RJ45 LED
To indicate the network connection status
(Refer to Description 4)
4
Power Jack
To connect DC12V 0.5A adapter
5
Power LED Indication
To indicate the power status (Refer to Description 5)
6
Status Indication
□
1Status : Port 1 mode indication (Refer to Description 6)
□
2Status : Port 2 mode indication (Refer to Description 6)
7
DIP Switch
To select the desired mode (Refer to Description 7)
Description
1Link speed of port 1 and 2 must be sync, or they are not able to activate network connection.
2Once the port 1 and 2 remain unlinked, the IP09C will automatically turn to Power Saving
mode.
4
User Manual
IP09CK
I
3RJ45 Pinout
4RJ45 LED
Date Rate
Light On
Light Off
Light Blinking
100Mbs
Enable
Disable
Data Transferring
10Mbps
Enable
Disable
Data Transferring
5 Power LED Indication
Green On
Green Off
Light Breathing
Power On
Power Off
Power Saving
6Status Indication:
□
1Status:
Blue On
Blue Off
Light Blinking
Blink twice
Long Reach
Ethernet
100BaseT-T1
Hardware Failure
□
2Status
Blue On
Blue Off
Light Blinking
10Mbps
Disable
100Mbps
7Dip Switch Setting
7.1 Auto Mode / Default (Highly Recommended)
Dip switch 1-2-3-4 all up (OFF)
Auto Mode to enable auto negotiation which automatically set up the link speed and
transmssion protocol.
(PIN TIA/EIA-568B)
PIN
Wire Color
1
Orange-white
2
Orange
3
Green-white
4
Blue
5
Blue-white
6
Green
7
Brown-white
8
Brown
5
User Manual
IP09CK
7.2 Auto+EEE Mode
Dip switch 1 down (ON), 2-3-4 up (OFF)
Auto+EEE mode supports Energy-Efficient Ethernet based on Auto Mode.
7.3 Advanced Mode
Please refer to the chart below to manually set up the Link Speed, and Modes
No.
Mode
↑OFF
↓ON
1
LINK SPEED
10Mbps
100Mbps
2
ETHERNET
Disable
Enable
3
100BASE-T1
Disable
Enable
4
LONG REACH
Disable
Enable
※Link speed of 10Mbps is not supported on 100BASE-T1 mode
Auto-Negotiation Priority
Priority
Mode
1 (Highest)
Long Distance 100Mbps
2
100BASE-T1
3
Long Distance 10Mbps
4
100BASE-TX Full Duplex
5
100BASE-TX Half Duplex
6
10BASE-T Full Duplex
7 (Lowest)
10BASE-T Half Duplex
IP09CK Package Include
2 x IP09C
2 x DC12V 500mA Power Adapter
4 x Screw
4 x Screw Plug
6
User Manual
IP09CK
I
Specification
ITEM NO.
IP09C
Support
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3bw 100BASE-T1 Ethernet
IEEE 802.3 Nway Auto-Negotiation
IEEE 802.3x Full Duplex Operation And Flow Control
IEEE 802.3az Energy Efficient Ethernet
Network Bandwidth
10/ 100Mbps
Transmission Distance
1000M at 10Mbps, 500M at 100Mbps
Ports & Interfaces
Ethernet Interface
1 x RJ45
Link Interface
1 x BNC
Power Interface
2 x (2mm) DC Jack
Power
Power Supply
DC 12V 500mA Regulated
Power Consumption
1W 90mA
Ambient Temperature
Operation
0 to 55℃
Storage
-20 to 85℃
Humidity
Up to 95%
Physical Characteristics
Dimensions
49 x 98.7 x 25mm
Weight
130g
Indice
Altri manuali SC&T Estensione
SC&T
SC&T HE01ERK Manuale utente
SC&T
SC&T IP05I Manuale utente
SC&T
SC&T 4K HDMI KVM USB/RS232/IR/Analog Audio CAT5e Extender over IP... Manuale utente
SC&T
SC&T UE03H Manuale utente
SC&T
SC&T IP02EPT Manuale utente
SC&T
SC&T IP03PT Manuale utente
SC&T
SC&T HKM01-4K Manuale utente
SC&T
SC&T IP05I Manuale utente
SC&T
SC&T DKM01 Manuale utente
SC&T
SC&T YE02DAL Manuale utente
