SCHUNK DL9-T PROFINET Istruzioni utente

Original manual

Control and Signal Module

DL9-M and DL9-T PROFINET

Assembly and Operating manual

Superior Clamping and Gripping

Imprint

2 02.00|DL9-M and DL9-T PROFINET |en

Imprint

This manual is protected by copyright. The author is SCHUNK GmbH & Co. KG. All rights

reserved. Any reproduction, processing, distribution (making available to third parties),

translation or other usage - even excerpts - of the manual is especially prohibited and re-

quires our written approval.

Technical changes:

We reserve the right to make alterations for the purpose of technical improvement.

Document number: 1011227

Version: 02.00 |14/09/2017|en

Dear Customer,

thank you for trusting our products and our family-owned company, the leading technol-

ogy supplier of robots and production machines.

Our team is always available to answer any questions on this product and other solutions.

Ask us questions and challenge us. We will find a solution!

Best regards,

Your SCHUNK team

SCHUNK GmbH & Co. KG

Spann- und Greiftechnik

Bahnhofstr. 106 – 134

D-74348 Lauffen/Neckar

Tel. +49-7133-103-0

Fax +49-7133-103-2399

[email protected]

schunk.com

Table of contents

02.00|DL9-M and DL9-

T PROFINET |en

Table of contents

Glossary ................................................................................................................... 5

Description............................................................................................................... 8

1.1

Master Module and Tool Module ............................................................................ 9

Installation .............................................................................................................. 11

2.1

Electrical Connections ............................................................................................ 11

2.2

Installing DL9-M Control/Signal Module................................................................ 16

2.3

Remove the DL9-M Control/Signal Module........................................................... 17

2.4

Installing DL9-T Control/Signal Module ................................................................. 17

2.5

Remove the DL9-T Control/Signal Module ............................................................ 18

2.6

PROFINET Interface ................................................................................................ 18

2.7

Utility Schematic..................................................................................................... 18

Product Information................................................................................................ 19

3.1

Master Module....................................................................................................... 19

3.1.1

PROFINET Interface Information................................................................. 19

3.1.2

Integrated Ethernet Switch......................................................................... 23

3.1.3

System Failure and Bus Failure LEDs........................................................... 24

3.1.4

Ethernet 1 and Ethernet 2 LEDs.................................................................. 26

3.1.5

Reset-To-Factory Push-Button.................................................................... 27

3.2

Arc Prevention Circuit............................................................................................. 27

3.2.1

Arc Prevention Circuit Behavior during Coupling ....................................... 28

3.2.2

Arc Prevention Circuit Behavior during Uncoupling................................... 30

3.3

Tool Module ........................................................................................................... 31

3.4

Safety System ......................................................................................................... 32

Operation................................................................................................................ 35

4.1

Inputs...................................................................................................................... 35

4.2

Error Conditions...................................................................................................... 37

4.3

Recommended Sequence of Operation ................................................................. 41

Maintenance and care ............................................................................................. 45

5.1

Pin Block Inspection and cleaning .......................................................................... 46

5.2

Seal Replacement ................................................................................................... 47

5.3

DL9 Device Replacement Procedures .................................................................... 47

5.3.1

Replace DL9 module with a new “out-of-the-box” DL9 module ................ 47

5.3.2

Replace DL9 module with an already-commissioned DL9 module ............ 48

Trouble shooting ..................................................................................................... 50

Recommended Spare Parts...................................................................................... 52

Table of contents

4 02.00|DL9-M and DL9-T PROFINET |en

Specifications .......................................................................................................... 53

Drawings ................................................................................................................. 55

Glossary

02.00|DL9-M and DL9-

T PROFINET |en

Glossary

Term

Definition

Application Processor 1

A board inside the DL9 module which controls solenoid

outputs, monitors function of the unlatch valves for

pressure and position, safety checking and diagnostics,

reports sensor status, protects outputs against short-

circuit overload, detects and reports status of the 24V

power supply, and provides cross-monitoring of the

pressure processor board.

Application Processor 2

A board inside the DL9 module which controls Unlatch

Valve 2, reports the pressure inside the valve module,

and provides cross-monitoring of the Application Pro-

cessor 1.

BF LED

BUS Failure LED; this is a standard Profibus status LED,

similar to the DeviceNet Network Status LED.

Clear Errors

An output supplied to the ATI master DeviceNet node

to clear all applicable error conditions

CL-RPC

ConnectionLess Remote Procedure Call.

DCP

PROFINET Discovery and Configuration Protocol.

EOAT

End-Of-Arm-Tool (end-effector).

Error on Latch Output

An input indicating a short circuit overload condition

exists with the Latch Output.

Error on Unlatch Output

An input indicating a short circuit overload condition

exists with the Unlatch Output.

Ethernet Switch

An Ethernet network component connecting multiple

communication partners with each other.

Functional Earth

GSDML File

A special kind of XML-based Device Description File

used by PROFINET

Latch (Lock)

The output supplied to the ATI Master module to cou-

ple the Tool Changer.

LLDP

Link Layer Discovery Protocol

Lock/Unlock Sensor Fault

An input indicating that the Locked and Unlocked in-

puts are high at the same time.

Locked

A proximity sensor input indicating that the coupling

mechanism is in the Locked position.

Output Power Available

An input indicating the presence of Output Power (US2)

at the ATI master module.

Power Sense

An input indicating the presence of Input and Logic

Glossary

6 02.00|DL9-M and DL9-T PROFINET |en

Term

Definition

Power (US1) at the ATI master module.

PROFINET

A communication system for Industrial Ethernet de-

signed and developed by PROFIBUS International. It

uses some mechanisms similar to those of the PROFI-

BUS field bus

RTL (Ready-To-Lock)

A proximity sensor input that senses when the ATI Tool

is in close proximity.

RTL Relay

A relay circuit present on the ATI Master module that is

driven by the RTL sensor and allows the Tool Changer

locking mechanism to retract when there is no Tool

present.

Safe to Unlatch

A calculated value that indicates it is safe to proceed

with an unlatch requested by the user.

SF LED

System Failure LED; this is a standard Profibus status

LED, similar to the DeviceNet Module Status LED;it has

a red part and a green part.

SNMP

Simple Network Management Protocol

SSFAULT

A diagnostic discrete input from the Euchner safety

switch, which is high when the switch detects an error.

SSO1 and SSO2

Inputs from a Euchner safety switch, which are high

when the tool changer is in the stand.

Switched Power Good

An input indicating the presence of Output Power (US2)

at the ATI master module.

Tool Power is On

The “Tool Power Is ON” bit is set high when the Arc

Prevention Circuit has activated power on the tool side.

If this bit is low there will be neither Input/Logic Power

nor Output power available on the tool.

Tool Present

A hard-connect input (sourced from the Tool) indicating

the Master and Tool are electrically connected to each

other.

Tool-ID

An input from the Master node reporting the values

from the Tool-ID switch on the Tool module.

Unlatch (Unlock)

The output supplied to the ATI Master module to un-

couple the Tool Changer.

Unlatch Enable

A virtual input used to describe the behavior of the

master module firmware in regards to allowing an Un-

latch output to be processed.

Unlocked

A proximity sensor input indicating that the coupling

mechanism is in the Unlocked position.

Glossary

02.00|DL9-M and DL9-

T PROFINET |en

Term

Definition

Unsafe Unlatch

An input indicating that an Unlatch command was re-

ceived which would result in an unsafe tool release and

was therefore not processed.

US1 Power Good

An input indicating the presence of Input and Logic

Power (US1) at the ATI master module.

V1Relay and V2Relay

Inputs from relays which should mirror the status of

SSO1 and SSO2.

Description

8 02.00|DL9-M and DL9-T PROFINET |en

Description

The DL9 modules enable the customer to control and communi-

cate with the Tool Changer through a network using a PROFINET

interface. A PROFINET node is established on the Master module,

but not on the Tool. Control of the Tool Changer is realized

through the Master Node along with the reporting of various Tool

Changer I/O. The Tool module supports Tool-ID reported through

the Master and functions as a pass-through for PROFINET network

and power to downstream equipment.

The DL9 module is to be used in combination with the JR4 valve

adapter with dual double-solenoid valves, for Latch/Unlatch con-

trol of the Tool Changer. When used in combination with the JR4

valve adapter, the DL9 achieves PL d safety reliability in accord-

ance with ISO standard 13849-1. The user is required to provide a

pneumatic supply source to the Tool Changer. Please refer to the

appropriate manual for specific module and Tool Changer re-

quirements.

The DL9-M/DL9-T modules are designed with a Safety circuit to al-

low the Tool Changer to be operated in the safest manner possi-

ble. In addition to supporting the standard Tool Changer input sig-

nals (Locked, Unlocked, and Ready-to-Lock proximity sensors) the

modules also support advanced diagnostic and fault reporting. Re-

fer to Safety System and Operation for more information on these

attributes.

A standard 5-Pin Push-Pull connector is provided on the Master

and Tool modules for interfacing with Auxiliary Power. The power

source for US1 and US2 Power must be a 24VDC certified power

supply or equivalent voltage controlled power supply and must be

protected by a user installed external 10 A fuse. A standard Push-

Pull RJ45 connector is provided on the Master and Tool modules

for interfacing with PROFINET. When the Tool Changer is coupled,

the Master and Tool modules pass signals via a spring-loaded pin

block. A flexible boot surrounds the pin block to seal the connec-

tion from moisture and liquid while coupled, see figure "DL9

PROFINET Master and Tool Modules".

Description

02.00|DL9-M and DL9-

T PROFINET |en

Module and Tool Module

DL9 PROFINET Master and Tool Modules

The DL9-M Module has an integrated 4-Pin Valve signal pin block

to provide the latch and unlatch signals to the solenoid valves. The

master module is equipped with M8 3-Pin connectors for the RTL1,

RTL2, Lock, and Unlock sensor connections.

The Master module has integrated M8 3-Pin valve adapter proxim-

ity sensor and M8 4-Pin valve adapter pressure sensor connectors

as part of the safety functionality.

The Master Module also incorporates an Arc Prevention Circuit

which extends the life of all electrical power contacts by eliminat-

ing arcing caused by inductive loads and high inrush current during

coupling/uncoupling. Refer to (3.2, Page 27)for additional in-

formation regarding the Arc Prevention Circuit.

1.1

Master Module

(DL9-M)

Description

10 02.00|DL9-M and DL9-T PROFINET |en

The DL9-M Module provides status LED’s to visually indicate their

operation. A reset button provides the ability to return to factory

default settings.

The DL9-T module requires a JR4-T Spacer Module to align the DL9

Master and Tool modules and mounts to the Tool body of the Tool

Changer.

The Tool module employs a series of thumbwheel switches for set-

ting of the Tool-ID input. This allows the customer to distinguish

between the different Tools that are being used in a robotic cell or

on a production line. The Tool-ID is reported through the Master

module bitmap. See (3.1.1, Page 19)for PROFINET bitmap and

detailed I/O information. A M12 5-pin connector provides connec-

tion to the non-contact safety switch that is integrated into the

safety circuit.

Tool Module (DL9-T)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SCHUNK Unità di controllo

SCHUNK

SCHUNK HLM Series Istruzioni utente

SCHUNK

SCHUNK RM-W Series Istruzioni utente

SCHUNK

SCHUNK GSM-R Istruzioni utente

SCHUNK

SCHUNK SDV-P Istruzioni utente

SCHUNK

SCHUNK MV Series Istruzioni utente

SCHUNK

SCHUNK KLM Series Istruzioni utente

SCHUNK

SCHUNK PPU-E Series Manuale utente

SCHUNK

SCHUNK ELKE 24 Manuale utente

SCHUNK

SCHUNK RP Series Istruzioni utente

SCHUNK

SCHUNK SDV-P Istruzioni utente

SCHUNK

SCHUNK LM Series Istruzioni utente

SCHUNK

SCHUNK PMPS/F 16 Istruzioni utente

SCHUNK

SCHUNK ELP Series Istruzioni utente

SCHUNK

SCHUNK SRU 20 Istruzioni per l'installazione e il funzionamento

SCHUNK

SCHUNK PCFC Istruzioni utente

SCHUNK

SCHUNK GSM-P Istruzioni utente

SCHUNK

SCHUNK PED Series Istruzioni utente

SCHUNK

SCHUNK ELKE 24/2F Istruzioni utente

SCHUNK

SCHUNK PMP Istruzioni utente

SCHUNK

SCHUNK ELB Series Istruzioni utente

SCHUNK

SCHUNK GSM-P 32 Guida all'installazione

SCHUNK

SCHUNK KEH-P Istruzioni utente

SCHUNK

SCHUNK LDH Series Istruzioni utente

SCHUNK

SCHUNK EPM Istruzioni utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente