SDC 180 Series Manuale utente
1. Determine the appropriate mounting configuration for your application (Header mount or Top-jamb or Side-jamb
mount.
2. Determine the handing for your application.
3. Remove the lock housing cover. Based on the mounting information determined on steps 1 & 2 above, adjust
the Auto Relock Switch (ARS) in the bolt chamber bracket as described below.
3a. Remove the ARS insert and install the ARS switch as shown. Replace the plastic insert.
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
P:\INST INSTRUCTIONS\BOLT LOCKS\INST-180_280 REV H 10-21 Page 1
180 / 280 SERIES
CONVENTIONAL DIRECT THROW
SURFACE MOUNT BOLT LOCK
Header
Mount
Top-
Jamb
Side-
Jamb
DOOR
FRAME HEADER
LOCK
STRIKE
END VIEW
Header Mount
Outswing Door
FRAME HEADER
OR SIDE JAMB
LOCK
STRIKE
DOOR
Top or Side Jamb
Inswing or Sliding Door
Mounting
Plate
ARS Cover
Insert
Bolt
Chamber
Bracket
Perpendicular to
Mounting Plate
Parallel to
Mounting Plate
Mounting Configuration Auto-Relock Switch Orientation
Header Mounted - LHR Perpendicular to the mounting plate
Header Mounted - RHR Perpendicular to the mounting plate
Top Jamb or Side Jamb - Swing (LH or RH) Perpendicular to the mounting plate
Top Jamb - Sliding to Left* Parallel to the mounting plate
Top Jamb - Sliding to Right* Parallel to the mounting plate
*Tob Jamb Sliding Door requires a positive stop
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
P:\INST INSTRUCTIONS\BOLT LOCKS\INST-180_280 REV H 10-21 Page 2
5. Mark and drill as follows: Holes 1, 2, 3, and 4 for #10 sheet metal screws or 10-32 x 1/2 machine screws.
Hole 8 – 3/8" diameter for wire.
Block strike: Holes 5 and 6 or 12 and 13 for 1/4 - 20 machine screw.
6. Tap holes as required.
7. Mount lock and strike block.
8. Attach power leads as shown on Page 3. When bolt is thrown, check alignment of bolt and strike. There should
be no binding on the bolt. Leading part of strike block should be 1/8" away from the lock (1/8" is maximum
distance). If this is correct, tighten mounting screws.
9. Check lock operation for any last adjustments.
10. Re-install housing cover.
4. Configure the strike block assembly
(Choose 4a, 4b, or 4c):
Strike Block
ARS magnet
Strike Insert
w/ screws
Block Shim
(use as
needed)
4c. For Top Jamb (swing or slide) or Side Jamb
Strike hole
away from
magnet
This end
towards the
door
4b. For Header-mounted, LHR
Strike hole
away from
magnet
This end
towards the
door
4a. For Header-mounted, RHR
Strike hole
towards
magnet
This end
towards the
door
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
**AC Power requires
the PR-1000
PR-1000
VOLTAGE
REGULATOR
YEL/BLK (~)
YEL (~) or (+DC)
(-)
+
Access
Control or
Push Button
(N/C)
N/O
N/C
COM
AC
POWER
BLK (-DC)
RED (+)
WHT (-)
ORG
BLU
WHT/BLK
Not
Used
(~)
(~) DC
POWER
INPUT
Solenoid
180 ARS
(DOOR CLOSED)
YEL GRY
*See below for
solenoid wiring
P:\INST INSTRUCTIONS\BOLT LOCKS\INST-180_280 REV H 10-21 Page 3
LOCK WIRING
180 Wiring:
280 Wiring:
Solenoid Voltage Configuration:
NOTE: The SDC PR-1000 Power Regulator module is included with the 180/280 bolt lock, and is required for proper
operation. Installing the PR-1000 reduces the power consumption of the bolt locks after activation of the lock, allowing
for a heat reduction to the bolt lock. Bypassing the PR-1000 will cause damage to the 180/280 bolt lock.
PR1000 Input Voltage: 12/24 VDC/AC (+/-10%) DC voltage is recommended for optimal performance
DIMENSIONS:
FINISH:
BOLT:
SOLENOID:
FUNCTION:
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
PR-1000
VOLTAGE
REGULATOR
YEL/BLK (~)
YEL (~) or (+DC)
(-)
+
AC
POWER
BLK (-DC)
ORG
BLU
WHT/BLK
(~)
(~) DC
POWER
INPUT
ACCESS
CONTROL
(N/O)
N/O
N/C
COM
RED (+)
WHT (-) Solenoid
ORG GRY
280 ARS
(DOOR CLOSED)
*See below for
solenoid wiring
**AC Power requires
the PR-1000
SPECIFICATION
Lock: 2" x 2" x 6" / Strike Block: 2" x 2-1/4” x 1"
US28 standard
1/2" diameter, 1/2” throw
.9 A @ 12VDC / .45 A @ 24VDC (Continuous Duty)
180, power to lock
280, power to unlock
ELECTRICAL DATA:
Dual Voltage (180/280)
12VDC@ .9 Amp (max.)
24VDC@ .45 Amp (max.)
Continuous Duty
RED (+)
BLU
BLK
WHT (-)
12VDC SOLENOID
CONFIGURATION
12VDC @
900mA (max)
RED (+)
BLK
BLU
WHT (-)
24VDC @
450mA (max)
24VDC SOLENOID
CONFIGURATION
P:\INST INSTRUCTIONS\BOLT LOCKS\INST-180_280 REV H 10-21 Page 4
BLOCK
STRIKE
12 13
BLOCK
STRIKE
RIGHT HAND
(LHR)
6
5
5
6
BLOCK
STRIKE
STOP STOP STOP
LEFT HAND
(RHR)
LOCK
TEMPLATE
TEMPLATE
FOLD ON DOTTED LINE AND HOLD AGAINST STOP
FOLD ON DOTTED LINE AND HOLD AGAINST STOP
MOUNTING PLATE
4X #10
1
24
3
8
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
Questo manuale è adatto per i seguenti modelli
3
Altri manuali SDC Serratura della porta
SDC
SDC PD2090A Manuale utente
SDC
SDC Z7835 Series Manuale utente
SDC
SDC ZY7500 Series Manuale utente
SDC
SDC ZA7200 Series Manuale utente
SDC
SDC 30-4-12 Manuale utente
SDC
SDC Spacesaver 1091 ADMR Manuale utente
SDC
SDC SK-82 Manuale utente
SDC
SDC 352 Narrow Line EMLock Manuale utente
SDC
SDC E72K-A CIVIC SERIES Manuale di installazione
SDC
SDC FS23M Series Manuale utente
SDC
SDC EntryCheck E75 Series Manuale utente
SDC
SDC 30-4 Manuale utente
SDC
SDC Z7500 Series Manuale utente
SDC
SDC 1511S Manuale di istruzioni
SDC
SDC Z7800 Series Manuale utente
SDC
SDC E70PS Series Manuale del proprietario
SDC
SDC 45 Series Manuale utente
SDC
SDC 1511S Manuale utente
SDC
SDC S6300 Series Manuale utente
SDC
SDC PBD2090A Manuale utente
