Sentry ST730S Manuale utente
Anemometer
ST730S
Instruction Manual
ST730S
REACH
(SVHC)
730S
Anemometer
REACH
(SVHC)
RoHS
使用說明書
Instruction Manual
Table Content
1. Product Introduction----------------------1
1-1 Features-----------------------------------1
1-2 Application--------------------------------2
2. Safety Information----------------------------2
2-1 Cautions-------------------------------2
2-2 Safety Symbols--------------------------3
3. Specifications----------------------------------4
3-1 General Specification------------------4
3-2 Technical Specification----------------5
4. General Descripts-----------------------------6
4-1 Unit Diagram-----------------------------6
4-2 LCD Panel--------------------------------7
4-3 Battery Placement----------------------8
4-4 AC Power---------------------------------8
4-5 Sensor Tip Description-----------------9
5. Mode Functions------------------------------10
5-1 Air Velocity / Air Temperature
Measurement--------------------------11
5-2 Maximum/Minimum/Average
Measurement--------------------------11
5-3 Data Record / Recall------------------12
6. Advanced Set Functions-----------------13
6-1 Air Velocity Unit Setting--------------13
6-2 Temperature Setting------------------13
6-3 Backlight ON/OFF---------------------13
1
1. Product Introduction
Thank you for purchasing this Anemometer.
The Anemometer is an air velocity and
temperature of air measuring instrument. To
measure an air velocity, put sensor head face to
the air velocity value.
1-1 Features
Combination of hot wire and standard
thermister, deliver rapid and precise
measurement event at low air velocity.
Wide range measurement of air velocity,
fast response time.
Multi-function for air velocity measurement:
m/s, km/h, ft/min, mile/h.
Super large LCD with dual function display,
read the air velocity & temperature at the
same time.
Data hold and record / recall maximum,
minimum, and average reading.
Ultra low power consumption in shutdown
mode.
Auto power off after 10 Minutes of idle.
2
1-2 Applications
Air conditioner
Refrigerated case
Ventilation system
Furnace flow velocity
Fans / motors / blowers
Environmental testing
Manufacturing processes of semiconductor
technology
2. Safety Information
Read the following safety information carefully
before attempting to operate or service the meter.
Only qualified personal should perform repairs or
servicing not covered in this manual.
2-1 Cautions!
DO NOT submerge the unit in water.
This product is not designed for use in
medical evaluation. The product can only be
used to measure body temperature simply
for reference. They are meant for industrial
and scientific purpose.
3
2-2 Safety symbols
Dangerous, refer to this manual before using
the meter.
CE Certification
This instrument conforms to the following standards:
En61326: Electrical equipment for measurement,
control and laboratory use.
IEC61000-4-2: Electrostatic discharge immunity test.
IEC61000-4-3: Radiated, radio-frequency,
electromagnetic field immunity test.
IEC61000-4-8: Power frequency magnetic field
immunity test.
Tests were conducted using a frequency range of
80-1000 MHZ with the instrument in there orientations.
The average error for the three orientations is ±0.5°C
(±1.0°F) at 3V/m throughout the spectrum. However,
between 781-1000MHZ at 3V/m, the instrument may
not meet its stated accuracy.
Restrict to use of six substances within
electrical and electronic equipment (EEE), thereby
contribution to the protection of human health and the
environment.
The device may not be disposed in trash. It
promotes the re-use recycling and other forms of
recovery of used materials and component, and to
improve the environmental performance of all
operators (manufacturers, traders and treatment
facilities) involved in the life cycle of products. Dispose
of the product appropriately in accordance with the
regulations in force in your country.
The device of used materials content no
substances that list of proposed REACH substances of
very high concern.
4
3. Specification
3-1General Specification
Model 730S
Measurement Air Velocity : m/s, ft/min, km/h, mile/h, knots
Temperature: °C and °F
Sensors Air Velocity / Air Flow Sensor : Hot Wire
Operating Temp. 32~122°F (0~50°C), 10~90%RH
Storage Temp. -14~140°F (-10~60°C)
Record Function Yes (9 points)
Sample Time Approx. 0.5 sec.
AC Power YES
Multi-LCD Display YES
Max / Min / Avg YES
LCD Backlight YES
Data Hold YES
Auto Power Off 10 Minutes of idle
(30 Minutes with AC Power)
Dimensions
7.24”×2.75”×1.57” (184×70×40mm)
Telescope probe : approx. 70.8”
(1800mm) include wire rod.
Weight Approx. 12.8oz (363g) with battery
Accessories 9Vbattery, Instruction manual, Carrying
case, AC Input, USB Transmission line.
5
3-2 Technical Specification
Model 730S
Range
Air Velocity:
0~40m/s, 0~7,874ft/min, 0~144km/h,
0~89.5mile/h,0~77.75knots
Air Temperature: 32~158°F (0~70°C)
Resolution
Air Velocity:
0.01m/s, 0.1ft/min, 0.01km/h, 0.01mile/h
0.01knots
Air Temperature: 0.1°F(0.1°C)
Accuracy
(%reading)
Air Velocity:
±(0.03+3%)m/s, ±(5.9+3%)ft/min,
±(0.11+3%)km/h, ±(0.07+3%)mile/h,
±(0.06+3%)knots
Air Temperature: ±1.5°F (0.8°C)
6
4. General Descriptions
4-1Unit Diagram
○
1 Power Button
○
2 LCD Screen
○
3 REC (↲) Button
○
4 ▼Down Button
○
5 Hold Button
○
6 AC Input
○
7 Backlight Button
○
8 Mode (SET) Button
○
9 ▲Up Button
○
10 Probe Socket
○
11 Sensor Head
○
12 Probe Plug
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Sentry Strumento di misura
Sentry
Sentry ST-5 Series Manuale utente
Sentry
Sentry Saf-T-Vise STV-HP2 Manuale di istruzioni
Sentry
Sentry ST520 Manuale utente
Sentry
Sentry 200 Manuale utente
Sentry
Sentry Z10000 Manuale di istruzioni
Sentry
Sentry ST 723 Manuale utente
Sentry
Sentry Level-Lenz Manuale di istruzioni
Sentry
Sentry ST 722 Manuale utente
Sentry
Sentry CPS-10 w/ Batt Manuale di istruzioni
