Server Sir Kensington's ECD Manuale utente
For purchasing our Volume Countertop Dispenser. This
portion controlled unit is sealed and sanitary, achieves
excellent evacuation and has only a few parts for easy
clean-up.
SIMPLIFY CONDIMENT MANAGEMENT— GO POUCHED
Thank You
Volume Countertop Dis-
penser
MODEL: ECD
06991
Use with
1½ gallon pouches
with16mm tment
or
3 gallon pouches
Page 2
06991 DISPENSER PARTS
LEVER
07014
LID
06998
HINGE PINS (2)
07161
ROLLER
07056
EVACUATION
PLATE
07814
TORSION SPRING
07813
POUCH SUPPORT
07811
SHROUD
06996
CAP
(for foot)
87339
FOOT
81169
PUMP 06992 DETAILS
FOR 1½ GALLON POUCH:
USE 16MM CONNECTOR
07381
6"TUBE
06993
DISCHARGE
FITTING
07796
PUMP HOUSING
07388
PINCH VALVE 07798
DOME 07383
FOR 3 GALLON POUCH:
USE 38MM CONNECTOR
07588
PUMP
06992
11"BRUSH
82049
Page 3
SAFETY
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly
to comply with local sanitization requirements.
According to food and safety regulations, most
foods must be stored and/or served at certain
temperatures or they could become hazardous.
Check with local food and safety regulators for
specic guidelines. Server Products, Inc. cannot be
responsible for the serving of potentially hazardous
product.
NSF International lists this pump as:
“Not acceptable for dispensing potentially
hazardous foods.”
PORTION CONTROL
THE LID IS SET TO DELIVER 1 OZ PORTIONS.
1/4 OZ
3/4 OZ
1/2 OZ
1 OZ
Install hinge pin through center roller hole
and desired portion hole on lever.
Pin snaps into place.
If lid reassembly is needed,
or to specify a different portion size:
One hinge pin attaches lever to lid.
Second hinge pin attaches roller to lever.
(Controls portion dispensed.)
Page 4
PUMP ASSEMBLY WASH ALL PARTS PROPERLY
BEFORE USE. See page 7.
into pump housing discharge tube.
Place loop of tting around peg on end of
discharge tube to secure.
INSERT DISCHARGE FITTING
5
INSERT PINCH VALVE
1
into pump housing.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.
Wrap loop
around lower
opening to
secure dome.
INSTALL DOME
2
Press dome into
housing fully.
Ensure valve ap
covers bottom
opening.
Lubricate with a small amount of clean water.
Rotate and position until both pegs on
housing t into holes on tube.
INSTALL TUBE
3
Lubricate connector with a small amount of clean water.
Rotate and position until both pegs on connector t into holes on tube.
Connector end must point away from discharge tube.
INSERT CONNECTOR
4
FOR 1½ GALLON POUCH:
USE 16MM CONNECTOR
FOR 3 GALLON POUCH:
USE 38MM CONNECTOR
Page 5
UNIT SETUP
ATTACH POUCH TO PUMP
1
Slide pouch and pump into
pouch support within shroud.
INSTALL PUMP
2
PLACE LID ON TOP
3
Press lever several times until you see
product in discharge tube.
PRIME PUMP
4
Firmly press piercing connector
into center of pouch tment.
An audible click indicates
a secure connection.
Insert connector into
pouch tment.
Tighten threaded ring
to secure.
CLICK
FOR
1½ GALLON POUCH
16MM CONNECTOR
FOR 3 GALLON POUCH
38MM CONNECTOR
Page 6
TAKE-DOWN & DISASSEMBLY
REMOVE PUMP & POUCH
2
DETACH PUMP FROM POUCH
3
REMOVE LID
1
FLUSH & RINSE PUMP
4
Place lower end of pump into container of
hot water. Pump until all remaining product is
expelled and only water ows from discharge
tube.
DISASSEMBLE
5
Page 7
This unit is constructed
with stainless steel— one
of the best materials for
food serving and storage.
If you notice corrosion beginning on
any stainless steel surface, you may need
to change the cleansing agent, sanitizing
agent, or the cleaning procedures you are
using.
CARE OF STAINLESS STEEL
• A mildly abrasive nylon or brass brush may
be used to remove any stubborn food or
mineral deposits on interior surfaces of unit.
• Fully rinsing and drying all parts can help
prevent corrosion. Elements and minerals in
tap water can accumulate on stainless steel
parts and create corrosion.
• Do not use products containing acids,
alkalines, chlorine, or salt. These agents can
corrode stainless steel.
CLEANING
RINSE
fully with clear water.
3
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.
4
AIR DRY
all parts fully.
5
Use dishwashing soap,
hot water
and nylon brush
• Pump is dishwasher safe
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine.
• Do not use metal scrapers or cleaning
pads that could scratch surfaces.
DISASSEMBLE & CLEAN
all washable parts with soap and hot water.
Use brush to clean any conned areas.
2
FLUSH & RINSE
all pump surfaces with hot water.
Place lower end of pump into container
of hot water and operate pump until all
remaining product is expelled and only hot
water is discharged.
1
PUMP CLEANING
UNIT CLEANING • External surfaces may be wiped clean with
a clean damp cloth.
• Glass and surface cleaners approved for
use in food contact areas may be used.
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use metal scrapers or cleaning
pads that could scratch surfaces.
Page 8 Manual #EM_01962_RevA 022222
GENERAL SERVICE,
Before sending any item to Server Products for
service, repair, or return, contact Server Products
customer service to request a Return Authorization
Number. Merchandise must be sent to Server
Products with this number. Service is extremely
prompt. Typically, units are repaired and ship out
within 48 hours of receipt.
Merchandise being returned for credit must be in
new and unused condition and not more than 90
days old and will be subject to a 20% restocking
charge.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.
TROUBLESHOOTING
• Ensure pinch valve is inserted in housing.
• Ensure connector is snapped fully in place to
tment in pouch.
• Ensure pump is properly attached to pouch.
• Clean pump thoroughly.
• Ensure pump is properly installed into retaining
slots inside front wall of shroud.
PRODUCT DOESN’T PUMP?
• Wet parts with clean water to help t.
DIFFICULT TO ATTACH PARTS?
• Clean thoroughly. Food residue could prevent
a tight seal between dome and housing.
• Ensure dome edges are ush with housing.
DOME POPS OFF?
NEED HELP?
Please be prepared with your Model, P/N and
Series located on the lid or base of the unit.
Example:
Chat with us!
262.628.5600 | 800.558.8722
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA MODEL
XXXX
P/N
#####
SERIES
##X ##X
SERVER PRODUCTS
This Server product is backed by a two-year
limited warranty against defects in materials and
workmanship. See Server-Products.com for details.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Server Distributore
Server
Server Mix-N-Serve 05550 Manuale utente
Server
Server SY Manuale utente
Server
Server InSeason INS Manuale utente
Server
Server EZ-Cream 06C Series Manuale utente
Server
Server Express SE-3 Manuale utente
Server
Server TOUCHLESS EXPRESS Manuale utente
Server
Server 85783 Manuale utente
Server
Server SlimLine DFD Manuale utente
Server
Server Express Direct-Pour SE-SS-DP Manuale utente
Server
Server BP-1 Manuale utente
Server
Server BP-1 Manuale utente
Server
Server BP-1 88574 Manuale utente
Server
Server Extreme ECD Manuale utente
Server
Server CerealServ DFD-C Manuale utente
Server
Server 06H Series Manuale utente
Server
Server EZT-S Manuale utente
Server
Server InSweeten INS Manuale utente
Server
Server SlimLine DFD Manuale dell'operatore
Server
Server 05H Series Manuale utente
Server
Server Shake Shack 85751 Manuale utente
