Seta Target Systems SCORE10/Pro Manuale utente
SCORE10 Version 20.1
1
Operating Instructions for
electronic scoring
SETA SCORE10/Pro
SETA Target Systems
Zeller Straße 1
DE-64720 Michelstadt
service@seta-online.com
SCORE10 Version 20.1
2
Translation
For deliveries to t e EEA countries, t e operating
instructions must be translated into t e language of
t e country of use.
If any discrepancies occur in t e translated text, t e
original instruction manual (German) s ould be
consulted or t e manufacturer s ould be contacted.
Copyright ©
T e reproduction, distribution and utilization of t is
document as well as t e communication of its
contents are strictly pro ibited unless expressly
permitted. Violations require compensation.
All rig ts reserved.
SCORE10 Version 20.1
3
1 Description of the System
T is c apter describes t e
o Warning notices and t e
o Components of t e system explained
o General information on operation
.
WARNING
Modification of the system may only be carried out by specially
authorized and instructed persons!
Only qualified specialists are allowed to carry out changes,
maintenance and service!
Repairs and troubleshooting may only be carried out by the
manufacturer or by a customer service commissioned by the
manufacturer!
WARNING
The S ORE 10 is to be used exclusively for compressed
airguns up to 7.5 Jules at a distance of 10m.
The consequences of improper use can be serious or slight
personal injury, damage to property or the environment.
For damages due to improper use, no liability is accepted.
SCORE10 Version 20.1
4
1.1 Explanation of the components
SETA Electronic Targets are designed to ensure insallation and usage is easy and user
friendly. You can set up entire system in few minutes.
The system consists essentially of the following components:
Tripod
T e Tripod consists of 3 components w ic ave to be assembled according to t e drawing.
Before assembling t e measuring frame, make sure t at all screws and nuts ave been
tig tened. Let t e plate on t e tripod look over t e front. C eck t e position of t e feet and t e
clamping on t e tripod.
Wallmounting Bracket
T e attac ment of t e wall mount is made by means of t e mounting plates and t e 80/40
Profils. Before mounting t e measuring frame, make sure all screws and nuts ave been tig -
tened.
SCORE10 Version 20.1
5
.
Important note
T e center of t e target s ould be at 140 cm eig t from t e ground.
You can order an aluminum tripod or use your existing stand. For wall mounting you
can use our wall mounting bracket.
Measuring frame
We deliver t e measuring frame fully assembled. T is is mounted on t e tripod or on t e wall
bracket as s own in t e picture.
Pellet collector
T e Pellet collector is delivered fully assembled,
T is is in t e designated
Holder swiveled in.
T is bullet trap is exclusively for t e
use of compressed air or CO² weapons for a
maximum projectile energy of 7.5 joules to be used.
T e bullet trap is built wit 2mm s eet metal at a 45 °
angle, t e t ickness and t e angle are manufactured
according to t e specifications.
Strengt of t e material used corresponds to
min. required DIN 1623.
SCORE10 Version 20.1
6
Installation SETA Score 10
Step 1-Open front Door and insert Paper Template (Airpistol or Airrifle, depending on
discipline) in t e Template Holder.
Step 2-Insert PaperRoll in Paper Feed Holder, roll it down t roug t e support Strips
and over t e rubberized drive Roller.
SCORE10 Version 20.1
7
Step 3-Insert new Template (Air Rifle or Air Pistol) over t e Roll and close Front Door
SCORE10 Version 20.1
8
Step 4-Open t e Pellet Collector
Step 5-Insert Back Cover Paper (control Paper) and close t e Pellet Collector
(T e control Paper is not required for measuring, it is used only as proof of s ooting images for
various associations)
SCORE10 Version 20.1
9
Step 6-Seta Score 10 is ready.
Connect t e supllied Power Supply (24VDC, 1Amp) to t e socket.
Display computer /tablet/ PC
A tablet or PC wit Windows 10 is required for eac line.
Interface
T e interface is delivered fully assembled by us, t e M12 in-
dustrial connector is used to connect to t e measuring frame.
T e USB outlet is to be connected to t e computer or tablet.
T e jack connection of t e power pack is used for t e power
supply (24VDC / 2A).
We use a low voltage of 24VDC in all lines t at go to t e
target.
Definition of "low voltage"
T e European low voltage directive applies to alternating vol-
tages over 50V rms value and direct voltage over 75V and t e
product safety directive applies to t e segment of low voltage
w ic falls below t ese limit values.
If t e DC voltage is below 60V, t ere is no need for protection
against contact.
Connecting lines
Now connect t e interface to t e measuring system using t e
connection cable wit t e M12 industrial connector (standard
10m cable is located at t e interface and 5m cable at t e stand,
ot er lengt s can also be produced on request. For t e con-
nection between t e target and t e interface Only cables from
us s ould be used, ot erwise malfunctions and errors can oc-
cur.
SCORE10 Version 20.1
10
Software driver installation for the USB interface
Step 1 - Connect t e interface wit t e USB to your laptop.
(Please note t at an interface is permanently assigned ere. T e same USB connection
on your computer s ould always be used)
Step 2 - Download t e driver file from our omepage: www.seta-online.com under
downloads or from t e following link:
ttps://cdn.website-editor.net/90516910252b45ac95beaf7182ac7be5/files/uploaded/CH341SER.ZIP
Step 3 –
Unzip t e ZIP-file CH341SER.ZIP.
Step 4 –
Start t e driver file "SETUP.EXE" and t e click "INSTALL"
Step 5 –
Please wait a few seconds. T e required driver will be installed.
Indice
