SEWOO SLK-TL20X Series Manuale utente
TE20X Series ENG Rev. 07/2023
Aroot Co., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi- do, 18103, Republic of Korea
TEL : +82-31-8077-5000 / FAX : +82-31-624-5310
http://www.miniprinter.com
All specications are subject to change without notice
MODEL : SLK-TL20X Series
Receipt Printer User’s Manual
This device co mplies with part 15 of the FCC Rules.
Operation is subject to the following two conditions.
1) This device may not cause harmful interference, and
2) This device must accept any interference received,
including interference that may cause undesired operation.
Vic Barczyk
20280 S. Vermont Ave. STE 200, Torrance, CA 90502 | USA
+310-561-8030
Victor Almazan
Paseo de la Reforma No. 265 Piso 2.Ocina SBC. Col.
Cuauhtémoc, C.P. 06500 Ciudad de Mexico | Mexico
LA_Sales@miniprinter.com
Disposal of Old Electrical&Electronic Equipment(Applicable in the European Union and other Euro-
pean countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronics equipment. For more detailed information about recycling of this product, please contact your
local city oce, your household waste disposal service or the shop where you purchased the product.
10. Printer Cleaning 21
11. Linerless Printer 22
11-1. Linerless Printer Cleaning 22
11-2. Recommended Paper 22
12. Specications 23
13. Command List 25
14. Utilities 27
15. SW 28
Table of Contents
1. Parts Identications 3
2. Setting up the printer 4
2-1. Unpacking 4
2-2. Connecting the cables 5
2-2-1. Interface Connector 6
2-2-2. Cash Drawer Connector 8
2-3. Loading the Roll paper 9
2-4. Adjustment of paper width 12
3. Control panel and other functions 13
3-1. Control panel 13
3-2. Error indicators 13
4. Self Test 14
5. ASCII Print 15
6. ECO Mode 15
6-1. Font 15
6-2. Paper Reduce 16
6-3. Density 16
7. Printer Setting 17
7-1. Baudrate 17
7-2. Cutter 17
7-3. Error Beep 17
7-4. Melody 18
8. Hexadecimal Dump 19
9. Peripherals Connection 20
9-1. Bluetooth Connection (Option) 20
9-2. Wi-Fi Connection (Option) 20
4
34
3
2. Setting Up the Printer
2-1. Unpacking
Your printer box should include these items. If any items are damaged or missing, please contact
your dealer for assistance.
The Printer CD Roll Paper
Interface Cable(optional) Adaptor(Optional)
Cleaning pen(Optional)
1. Parts Identications
POWER SWITCH
COVER OPEN LEVER
CONTROL PANEL
Used to turn on/off
power to the printer.
Pull down this lever to
open the printer cover.
Features LED indicators to indicate printer
status and switches to operate the printer.
PRINTER COVER
Open this cover to
load or replace paper.
6
56
5
2-2-1. Interface Connector
D-SUB 25 Female Serial Centronics Parallel
Link LED Status LED
USB “B” Type Ethernet
USB Interface
PIN SIGNAL I/O DESCRIPTION
1 +5V - +5V
2DATA- - Printer transmit data line
3DATA+ - Printer transmit data line
4 GND - System Ground
Serial Interfaced
PIN SIGNAL I/O DESCRIPTION
2TxD Output Printer transmit data line RS-232C level
3 RxD Input Printer receive data line RS-232C level
4, 20 DTR Output Printer handshake to host line RS-232C level
6 DSR Input Data Send Ready
1, 7 GND - System Ground
2-2. Connecting the Cables
You can connect up the cables required for printing to the printer.
They all connect to the connector panel on the back of the printer, which is shown below :
INTERFACE CONNECTOR POWER CONNECTOR
CASH DRAWER CONNECTOR
INTERFACE CONNECTOR(USB)
Before connecting any of the cables, make sure that both the printer and the computer are turned
o.
8
78
7
2-2-2. Cash Drawer Connector
The printer can operate two cash drawers with a 6 pin RJ-11 modular connector.
The driver is capable of supplying a maximum current of 1.0 A for 510ms or less when not printing.
PIN SIGNAL Description
1Signal GND -
2Drawer kick-out drive signal 1 Output
3Drawer open/close signal Input
4+24V -
5Drawer kick-out drive signal 2 Output
6Signal GND -
Centronics Parallel Interface
PIN SIGNAL I/O DESCRIPTION
1 STROBE- Input Synchronize signal Data received
2~9 DATA0~7 Input/
Output Data bit Transmitted 0~7
10 ACK- Output Data receiving completed.
11 BUSY Output Impossible to print of data receiving.
12 PE Output Paper empty
13 SELECT Output Printer status for ON/OFF line
14 AUTO FEED- Input Paper auto feed signal
15 GROUND - System ground
16 GROUND - System ground
17 NC -
18 LOGIC-H - +3.3V
19~30 GROUND - System ground
31 INIT- Input Initialize
32 ERROR- Output Printer error
33 GROUND - System ground
34 NC -
35 NC -
36 SELLECT IN- Input Printer select signal
Ethernet Interface
PIN SIGNAL I/O
1 Data Out + Output Data +
2 Data Out - Output Data -
3 Data IN + Input Data +
4N.C
5N.C
6 Data IN - Input Data -
7N.C
8N.C
10
910
9
5 Be sure to note the correct direction that the paper comes o the roll.
X O
6 Pull out a small amount of paper, as shown. Then, close the cover.
7 Tear o the paper as shown.
2-3. Loading the Roll paper
NOTE
Be sure to use paper rolls that meet the specications. Do not use paper rolls that have the
paper glued to the core because the printer cannot detect the paper end correctly.
(Turn o power switch)
1 Make sure that the printer is not receiving data; Otherwise, data may be lost.
2 Open the paper roll cover by pushing down the cover open button.
3 Remove the used paper roll core if there is one inside.
4 Insert new paper roll as shown.
12
11 12
11
2-4. Adjustment of paper width
1 Please adjust the Paper Guide to t to the paper width as the direction of arrow.
2 Tight the screw after adjusting the Paper Guide.
3 Pull the edge of paper once the paper roll is installed correctly and close the Paper Cover.
CAUTION:
When the paper is jammed with cutter, the top cover might be stuck. In this case, repeat power on
and o several times.
If the top cover is still stuck, please follow the steps to release the papers from jamming.
1 Make sure the printer is turned o.
2 Take out DIP switch cover as shown.
3 Turn screw with drivers to a direction until paper is released from the cutter.
14
13 14
13
4. Self Test
The self-test result indicated whether the printer is operating properly. Also with this, user can
check following options or status of the printer.
Control circuit
Printer mechanism
Printing quality
ROM version
Interface setting
This test is independent of any other equipment or software.
Running the self test
1 Make sure the printer is turned o and the printer cover is closed properly before performing
the self test.
2 Turn the printer on holding the FEED button, then the self-test will start.
The self-test prints the printer setting value and then prints the following, and pauses. (Error
LED On)
SELECT MODE BY BUTTON
1. ASCII PRINT
2. SELECT BAUDRATE MODE
3. HEXADUMP MODE
3 Press the FEED button consecutively (1~3)
1. ASCII PRINT
(press the FEED button once)
Printing test page constructed with ACII code.
2. SELECT BAUDRATE MODE
(press the FEED button twice)
Set the speed of Serial Interface
(You can set the BAUDRATE in this mode)
3. PRINTER SETTING
(press the FEED button triple time)
Set the printer option.
(Serial baudrate, Cutting mode, Error beep, Melody)
3. HEXADUMP MODE
(press the FEED button quad time)
Printing the HEX value received from the interface
※ Wait for 5~6 seconds if you want to exit. Printer performs a cutting when exiting this mode
4 The printer is ready to receive data after nishing setting.
3. Control panel and other functions
3-1. Control panel
You can control the basic paper feeding operations of the printer with the button on the control
panel. The indicator lights help you to monitor the printer’s status.
Control Panel
Button
The button can be disabled by the ESC c 5 command.
Press the FEED button once to advance paper one line. You can also hold down the FEED button
to feed paper continuously.
3-2. Error indicators
This section explains the dierent patterns signaled by the three LED indicators located on the top
cover of the printer.
STATUS
PAPER ERROR POWER
REMARKS
RED RED GREEN
Power o OFF OFF OFF Normal power is not supplied to the printer
Power on OFF OFF ON Normal power is supplied to the printer
On line OFF OFF ON Normal error-free mode
Cover open OFF ON ON Close cover
Paper empty OFF ON ON Insert new paper roll
Paper near end ON OFF ON Paper is low
Test mode OFF OFF ON Ignored error led
16
15 16
15
6-2. Paper Redue
Reduce menu (Line space, Line feed, barcode[1D] height) was developed for
paper saving.
Line space
”Line space"
means the amount of feed when you intentionally generate newlines.
Line feed
”Line feed"
means the amount of feed when there is an automatic line break.
Barcode Height
”Barcode H eight”
means the height of the barcode when creating a one-dimensional barcode.
LINE SPACE SETTING
1. NORMAL
2. REDUCE 50%
3. REDUCE 75%
4. REDUCE 90%
LINE FEED SETTING
1. NORMAL
2. REDUCE 50%
3. REDUCE 75%
4. REDUCE 90%
1D BARCODE HEIGHT SETTING
1. NORMAL
2. REDUCE 50%
3. REDUCE 75%
4. REDUCE 90%
6-3. Paper Redue
Adjust the print density to save the power consumed by the printer.
SELECT DENSITY
1. NORMAL
2. LOW
3. DARK
5. ASCII Print
6. ECO Mode
ASCII PRINT is printing a test page constructed ASCII code. You can able to check the printer works
properly with this
The ASCII PRINT test automatically ends and cuts the paper after printing the following:
*** Completed ***
The printer is ready to receive data as soon as it completes the ASCII PRINT.
After entering the ECO MODE, the list which can select the ECO option will be
printed. Similar like Self Test, you can press the FEED button to select a ECO option.
Once the input performs properly, the printer shows a result and store.
ECO MODE
1. FONT SETTING
2. LINE SPACE SETTING
3. LINE FEED SETTING
4. BARCODE[1D] HEIGHT
5. DENSITY SETTING
6-1. Font
FONT SETTING menu can be change the Font mapping(FONT A / FONT B).
If you did not want other side font, you can disable that.
- FONT A : 12x24
- FONT B : 9x17
FONT SETTING
1. FONT A -> A / FONT B -> B
2. FONT A -> B / FONT B -> B
3. FONT A -> A / FONT B -> A
4. FONT A -> B / FONT B -> A
Indice
Altri manuali SEWOO Stampante
SEWOO
SEWOO SLK-T32EB Series Manuale utente
SEWOO
SEWOO LK-TL200 Manuale utente
SEWOO
SEWOO LK-P11 Istruzioni per l'installazione
SEWOO
SEWOO LK-T200 Manuale utente
SEWOO
SEWOO SLK-TS400 Manuale utente
SEWOO
SEWOO LK-P400 Manuale utente
SEWOO
SEWOO SLK-TE12 Series Manuale utente
SEWOO
SEWOO LK-P21 Manuale utente
SEWOO
SEWOO SLK-TE25 Manuale utente
SEWOO
SEWOO SLK-TE25 Manuale utente
SEWOO
SEWOO LK-P400 Manuale utente
SEWOO
SEWOO LK-P30 Manuale utente
SEWOO
SEWOO LK-P22 Manuale utente
SEWOO
SEWOO LK-P41W Manuale utente
SEWOO
SEWOO LK-P12 Manuale utente
SEWOO
SEWOO LK-P30 II Manuale utente
SEWOO
SEWOO SLK-D10 Manuale utente
SEWOO
SEWOO LK-P12 Guida utente
SEWOO
SEWOO SLK-TE21X Series Manuale utente
SEWOO
SEWOO LK-P41B Manuale utente
