Shining 3D AccuFab L4D Manuale utente
AccuFab L4D
Installation Guide
3D Printer
Remove foam ,take out the spare resin tank from the back of the
Remove the package, place the printer on the table,and open
Connect the power supply and press the power button on Wait for the printer stop moving, open the buckles and take out the
right side of the printer. During printer initialization. Platform will
Take out accessory box from fixing foam .
the printer chamber door. Remove fixing foam & inside
1）
3）4）
2）
5
5
10
11
7 5
6）
6
8 9
3 4
5）
“installation guide” and power cable .1
1 2
Open the package and take out the “product certificate” ,
Unpacking
2
1
34
5
6
8
11
9
Screen Protector
DO NOT remove the screen protector.
7
printer.
the printer.
go to the top position.
resin tank .Remove the protect film around the resin tank.
10
Put clean resin tank into the position. Lock the buckles for As the following picture shows, installation is completed.
Add Material
First Print
7）8）
11
(There are four positioning slots)
resin tank.
Note that the resin level
of minimum and maximum.
Note: You can also add resin during printing without pausing.
Please refer to the “AccuFab-L4D Quick Start Guide” in the flash drive. The flash drive can be used for data transmission later on.
10
should be between the indicator lines
Shake for 2 mins before pouring material into the resin tank to
avoid sediment.
10
11
Product Preview
Part List
①
① ② ③ ④ ⑤
⑤
⑥
⑦
⑥ ⑦ ⑧
⑧
②
③
④
Spare Resin tank Power Cable Network cable Quality Certification Disposable GlovesInstallation Guide
Build platform
Build platform
bracket
Chamber door
B-type USB port Network port
Resin tank
Touch screen
Power button Power port
Flash Drive Angular Knife Putty knife Brush Scraper
Cleaning Box Bolt Resin tank cleaner
Wrench
Cloth PET Card
Flash Drive：
Flash drive contains Installer of AccuWare, Printer profile
“*.sndev” , User Manual ,Quick Start Guide and “Factory test reports”
Used to remove models from the platform after printing
Angular Knife：
finished.
finished.
Used to remove models from the platform after printing
Putty Knife：
Used to clean extra resin on the model.
Brush：
Used to stir resin in the tank to avoid sediment.
Scraper：
Cleaning Box：
Cloth：
Used to level the platform and remove the cured layer.
PET Card：
Used to store parts or alcohol.
Used to clean optical path including projector lens, protection
glass and resin tank glass.
3D Printer
Technical resource:
S
Document Download Center:
upport Center:
Aftersales service:
Indice
Altri manuali Shining 3D Stampante 3D
Shining 3D
Shining 3D AccuFab-L4D Manuale utente
Shining 3D
Shining 3D einstart-c Manuale utente
Shining 3D
Shining 3D AccuFab-D1s Manuale utente
Shining 3D
Shining 3D einstart-c Manuale utente
Shining 3D
Shining 3D AccuFab-L4D Manuale utente
Shining 3D
Shining 3D AccuFab-D1s Manuale utente
Shining 3D
Shining 3D einstart-c Manuale utente
Shining 3D
Shining 3D Einstart Manuale utente
Shining 3D
Shining 3D EinScan-SE Manuale utente
Shining 3D
Shining 3D Transcan-C Manuale utente
