Siemens Cerberus Pyrotronics NIM-1M Manuale utente

Cerberus Division

P/N 315-099105-1

Siemens Building Technologies, Inc.

8 Fern ood Road

Florham Park, Ne Jersey 07932

Siemens Building Technologies, Ltd.

50 East Pearce Street

Richmond Hill, Ontario L4B 1B7 CN

Installation Instructions

CERBERUS PYROTRONICS

Model NIM-1M

Network Interface Modem Module

OPERATION

The CERBERUS PYROTRONICSTM Model NIM-1M

plug-in modem board mounts to and is connected to

the NIM-1W board to provide modem communication

capability for an MXL System XN T network.

The modem transmission line connected to the

NIM-1M can only be Style 4 and can be made using

standard 18 AWG shielded twisted pair or data grade

phone lines.

Note: A pair of NIM-1W / NIM-1M board sets is

referred to as a bridge in this document.

INSTALLATION

Remove all system power before installation,

first battery and then AC. To power up, connect AC

first, then the battery.

Setting the Switches

Before mounting the NIM-1M modem module on the

NIM-1W, set all the switches and configuration

jumpers on both modules. Refer to the NIM-1W

Installation Instructions, P/N 315-099106 for informa-

tion on setting the switches on the NIM-1W.

NIM-1M SETTINGS

The NIM-1M has three configuration headers (refer

to Figure 1). The NIM-1Ms are always connected in

board sets, or pairs, with NIM-1Ws to form the

bridge. Designate one board set as NIM-1M LOCAL

and the other as NIM-1M R MOT . Program the

NIM-1Ms as shown in Table 1.

1ELBAT

sM1-MINEHTGNIMMARGORP

LACOLM1-MINETOMERM1-MIN

1PJ NO 1PJ NO

2PJ NO 2PJ FFO

3PJ FFO 3PJ NO

Mounting

The NIM-1M is mounted on the NIM-1W with 4 nylon

spacers.

1. Snap the 4 nylon spacers into place in the holes

on the underside of the NIM-1M board in the

positions indicated in Figure 2.

2. Position the 4 spacers on the NIM-1M over the 4

holes on the component side of the NIM-1W.

Refer to Figure 3 for representative location of

the NIM-1M on the NIM-1W. Press the spacers

firmly into place in the NIM-1W one at a time.

Cable Connections from NIM-1M to NIM-1W

The NIM-1M has a cable attached to the underside

of the board that connects to JP2 of the NIM-1W.

The cable plug is polarized and connects one way

only. Refer to Figure 3 for the location of JP2.

Figure 1

NIM-1M Module Board

ELECTRICAL CONNECTIONS

Note: All connections to the NIM-1W / NIM-1M

board set are power limited to NFPA 70 per

N C 760. All connections are also supervised.

NIM-1M Modem Connections

Modem connection to the NIM-1M can be made

through the standard RJ11 jack (P2) or through TB1

(refer to Figure 2). If TB1 is used, connect TB1-1 TIP

Local to TB1-1 TIP Remote and TB1-2 RING Local

to TB1-2 RING Remote. P1 is for factory use only.

TB1 terminal assignments are as follows:

TB1-1 TIP

TB1-2 RING

TB1-3 LOCAL ARTH GROUND

Figure 2

Installing the Spacers on the NIM-1M Module Board

JP2

JP3

JP1

NIM-1M

TB1

INSERT 4 NYLON SPACERS

IN HOLES

IN POSITIONS INDICATED BY ARROWS

ON UNDERSIDE OF

BOARD

NIM-1W

JP4

JP2

JP1

D4 D5

SW1

SW2

87654321

–

ANY

TRBL

ANY

ENABLE XMIT

JP2

JP3

JP1

NIM-1M

TB1

Figure 3

Mounting the NIM-1M Module Board on the NIM-1M Module Board

TB1-3 must be connected to local earth ground. If

shielded cable is used, connect shield to local earth

ground at one side of modem connection only.

Note: When an MXL XN T network using the model

NIM-1W with model NIM-1M board set is

brought on line, there may be some delay in

network communications while the modems

on the model NIM-1M board establish com-

munications. This may cause a temporary

system trouble which can be cleared once

communications are established.

Refer to the NIM-1W Installation Instructions, P/N

315-099106, to continue with the installation of the

NIM-1W / NIM-1M board set.

P/N 315-099105-1

Indice

Altri manuali Siemens Unità di controllo

Siemens

Siemens SINAMICS DCM Scheda tecnica

Siemens

Siemens SINUMERIK 840D sl Foglio di istruzioni

Siemens

Siemens SIRIUS 3SB3 Manuale utente

Siemens

Siemens SIRIUS Manuale utente

Siemens

Siemens SINAMICS SM120 Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens 3VL93 Series Manuale utente

Siemens

Siemens VAI61 Series Manuale utente

Siemens

Siemens AS-Interface ASIsafe 3RK1205-0B.00-2AA2 Manuale utente

Siemens

Siemens LMV 5 Series Manuale dell'operatore

Siemens

Siemens DMS8000 MP4 Series Istruzioni operative e di manutenzione

Siemens

Siemens QAW910 Manuale utente

Siemens

Siemens SINUMERIK 802D sl Manuale del proprietario

Siemens

Siemens Simatic S7-300 Manuale utente

Siemens

Siemens FT2001-A1 Manuale utente

Siemens

Siemens CU240S DP-F Manuale utente

Siemens

Siemens Simatic S7-1500 Manuale utente

Siemens

Siemens SIMATIC 8DO 24 V DC/0.5 A HF Manuale utente

Siemens

Siemens WF 725 Manuale tecnico

Siemens

Siemens SINUMERIK 840D sl Manuale del proprietario

Siemens

Siemens MICROMASTER 411 Manuale utente

Siemens

Siemens Simatic S7-1500 Manuale utente

Siemens

Siemens RWF50 Guida utente

Siemens

Siemens HiPath optiPoint 410 Manuale di istruzioni

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente