Siemens CP 443-5 Extended Manuale utente

PROFIBUS interface

(9-pin D-sub female

connector)

Mode selector

Status and fault LEDs

SIMATIC NET

S7-CPs for PROFIBUS

Manual Part B4

CP 443-5 Extended for PROFIBUS

6GK7 443-5DX04-0XE0 Version 1 or higher (Firmware Version V6.1 or higher)

for SIMATIC S7-400 / S7-400H

Notes on the Product

B4-2 CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

Notes on the Product

Note

All notes in the product information bulletin that is supplied with this product are

valid and must be observed.

Compatibility with the Previous Version

Note

Make sure that you read the information regarding extended functionality and

restrictions in Chapter 6 of this manual!

B4-3

CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

Contents

Contents - Part A

PROFIBUS CPs - General Information See General Part. . . . . . . . . . . . . .

Note

Please remember that Part A of the manual also belongs to the description of the

CP. Among other things, it contains explanations of the safety notices, the

references to literature, and general information that applies to all S7 CPs for

PROFIBUS.

You can also obtain the current Part A from the Internet:

http://www4.ad.siemens.de/view/cs/de/1158693

Contents - Part B4

1 Properties / Services B4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Requirements for Use B4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 Use with the Current CPU Types B4-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 Converting older Systems B4-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 Installation and Commissioning B4-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Displays and Mode Selector B4-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 Performance Data B4-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Supported Transmission Rates B4-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Characteristics of the DP Interface B4-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Characteristics of S5-compatible Communication (SEND/RECEIVE Interface)

over FDL Connections B4-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 Characteristics of S7 Communication B4-20. . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 Parallel Use of Communications Services (Multiprotocol Operation) B4-20.

5.6 Time-of-day Synchronization B4-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.7 Data Record Routing B4-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.8 Use in Fault-tolerant Systems 1) B4-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.9 Other Characteristics B4-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 Compatibility with the Previous Product B4-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 Extended Functionality Compared with Previous Product: B4-25. . . . . . . . . .

6.2 Replacing Older Modules / Replacing Defective Modules B4-25. . . . . . . . . .

7 Technical Specifications B4-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 Properties / Services

B4-4 CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

1 Properties / Services

Application

The CP 443-5 Extended communications processor is designed for use in a

SIMATIC S7-400 (standard) and S7-400H (fault-tolerant system) programmable

controller. It allows the S7-400 / S7-400H to be connected to a PROFIBUS fieldbus

system.

You can use the CP as a router for data records intended for field devices (for

example PA slaves).

Services

The current version of the CP 443-5 Extended supports the following

communication services in the standard and H systems:

SPROFIBUS-DP with the following characteristics:

- DP master (class 1) (redundant operation in fault-tolerant system also

possible)

- Direct data exchange (DP slave to DP slave)

As a DP master, the CP 443-5 Extended is capable of enabling direct data

exchange for “its” DP slaves.

- SYNC /FREEZE (please refer to Tables 2-1 and 2-2)

The outputs or inputs can be synchronized from the within the user program

using system function SFC11.

- Constant bus cycle time (only in the standard system)

The ability to set a constant bus cycle time means that the DP master

always starts the DP bus cycle after the same interval.

- Selectable DP modes:

DPV1 functionality

(default in STEP 7) S7-compatible

DP master mode for:

SDP slaves complying with the

PROFIBUS DP-V0 and DPV1

standard

SSiemens DP slaves

(Refer to the information in Tables 2-1

and 2-2 on the required CPU)

DP master mode for:

SDP Slaves complying with the

PROFIBUS DP-V0 standard (DP

slaves complying with the DPV1

standard can only be used with

restricted functionality)

SSiemens DP slaves

(For more information on the topic of DPV1, refer to the STEP 7 / Hardware

Configuration online help)

1 Properties / Services

B4-5

CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

- CiR (Configuration in RUN) - in the standard system

By making a change to the configuration with CiR (Configuration in RUN), it

is possible to put a DP slave / DP slot extension into operation or take it out

of operation when necessary while the system is running.

In other words, you can configure and activate additional DP slaves or DP

slots while the S7 station is in RUN.

- Activate/deactivate DP slaves in the standard system

DP slaves can be activated and deactivated from the within the user

program using system function SFC12.

- Diagnostic Requests

As a DP master class 1, the CP 443-5 supports diagnostic requests of a DP

master class 2.

- Identifying the bus topology in a DP master system

As a DP master, the CP 443-5 Extended supports the measurement of the

PROFIBUS bus topology in a DP master system using a diagnostic repeater

(DP slave).

System function SFC103 in the user program can instruct diagnostic

repeaters to measure the PROFIBUS BUS topology in a DP master system.

When completed, the results of the measurements made by the diagnostic

data can then be read in and processed by the user program.

SS5-compatible communication (SEND/RECEIVE interface) on FDL

connections of the following types:

- specified FDL connections

- free layer 2 connections

- broadcast

- multicast

1 Properties / Services

B4-6 CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

SS7 communication and PG/OP communication

- PG functions with upload / download of FM modules, configuration /

diagnostics and routing

Note on routing: Dynamic switchover to alternative paths (for example if

there is a problem on one of the possible transmission paths) is not

supported.

- Operator control and monitoring functions (HMI)

- Client and server for data exchange on S7 connections via communications

function blocks (fault-tolerant S7 connections also possible)1)

- Download S7 connections and gateways in RUN.

STime-of-day synchronization via PROFIBUS

- The CP forwards time-of-day synchronization frames from the LAN to the

station (CPU = time slave) or from the station to the LAN (CPU= time

master) or this station is synchronized via a different LAN and the

time-of-day synchronization frame must be forwarded over PROFIBUS for

the synchronization of further stations.

- The CP supports time stamping of distributed process signals in conjunction

with the IM 153.

- Time-of-day status value (standard/daylight saving time switchover,

synchronization status)

SData record routing

You can use the CP as a router for data records intended for field devices (for

example PA slaves). One tool that creates such data records for assigning

parameters to field devices is SIMATIC PDM (Process Device Manager; see

also SIMATIC PDM documentation...).

The services of the CP 443-5 Extended module listed above can be used at the

same time.

Blocks for S7 communication (see also STEP 7 online help or

“System Software for S7-300/400 System and Standard Functions” manual):

BSEND SFB 12

BRCV SFB 13

PUT SFB 14

GET SFB 15

USEND SFB 8

URCV SFB 9

START SFB 19

STOP SFB 20

RESUME SFB 21

STATUS SFB 22

USTATUS SFB 23

CONTROL SFC 62

1 Properties / Services

B4-7

CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

Project engineering

To configure and use any functions, you require STEP 7 as of V5.3.

It is possible to configure over the MPI or LAN/PROFIBUS.

Programming - Using Blocks

For some communication services, there are “off-the-peg” blocks (FCs/FBs)

available that implement the interface in your STEP 7 user program. You will find a

detailed description of these blocks in the NCM S7 for PROFIBUS manuals.

Notice

We recommend that you always use the latest block versions for all module types.

You will find information on the latest block version and links to download the

current blocks in our Customer Support on the Internet:

http://www4.ad.siemens.de/view/cs/en/8797900

If you are using older block types, this recommendation only applies if you also

have the latest firmware version.

You will find further information and Internet addresses in the Preface of the

General Part of this manual.

Replacing Modules without a Programming Device

When installing the CP 443-5 Extended, the configuration data of the CP are

always stored in the CPU. Therefore replacing modules is possible without having

to download the configuration data from the PG.

The stored configuration data is protected from power outage by battery backup or

by plugging a flash memory card into the CPU.

2 Requirements for Use

B4-8 CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

2 Requirements for Use

The CP 443-5 Extended V 6.1 described here is supported by all CPU operating

systems in the versions listed in Tables 2-1 and 2-2.

2.1 Use with the Current CPU Types

Limits and Conditions

To use the CP type described here, the following limits and constraints apply within

a rack:

SNumber of operable CPs: 14

SMax. number of external DP chains (CP as DP master) : 10

Notice

The number CPs that can be operated as DP masters depends on the number of

CP 443-1 Advanced modules operated as PROFINET IO controllers in the

S7-400 station. In total, 10 CPs can be operated as

SPROFINET IO controllers (CP 443-1 Advanced) - maximum 4

SDP masters (CP 443-5 Extended) - maximum 10

SMulticomputing is supported (except with CiR and H systems)

System Environment

The CP 443-5 Extended is supported by the S7-400 CPUs and CPU operating

systems with the order numbers and versions listed in the table below.

From the table, you can see which functionality is supported when you use the CP

443-5 Extended V 6.1 with the various CPU types: The following characteristics

are listed:

SCPU type, order number and version

SOption of multicomputing

SThe number of CPs that can be operated with one CPU

SThe maximum number of external DP chains of an S7 station;

SThe number of AG-SEND or AG-RECV calls on the SEND/RECEIVE interface

that can be active at the same time (data exchange on FDL connections over

PROFIBUS and corresponding connections over Industrial Ethernet).

SWhether the CPU supports SYNC/FREEZE functionality (SFC11) via the CP.

SWhether the CPU supports the activate / deactivate (SFC12) DP functionality

via the CP.

2 Requirements for Use

B4-9

CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

SWhether the CPU supports the functionality for identifying the bus topology in a

DP master system (SFC103) via the CP.

SDPV1 functionality

SCiR functionality (DP slave / DP slot, configurable extension)

Notice

ET 200M devices that were assigned to SYNC/FREEZE groups with STEP 7,

must not have modules of the type FM or CP inserted.

Table 2-1 Use with the Current CPU Types

CPU Order Number of the

CPU

Firmware version

CPU:

6ES7... Number of AG-SEND or AG-RECV calls at

same time

SYNC/FREEZE functionality

DP-V1 functionality

CiR / HCiR functionality 1)

Activate / deactivate

DP slave

Identify bus

topology

CPU 412 ..412-1XF04-0AB0 As of V4. 24 /24 + + + + -

As of V4.1 24 /24 + + + + +

CPU 412-2 ..412-2XG04-0AB0 As of V4. 24 / 24 + + + + -

As of V4.1 24 / 24 + + + + +

CPU 414-2 ..414-2XG04-0AB0 As of V4. 24 / 24 + + + + -

As of V4.1 24 / 24 + + + + +

CPU 414-3 ..414-3XJ04-0AB0 As of V4. 24 / 24 + + + + -

As of V4.1 24 / 24 + + + + +

CPU414-4H ..414-4HJ04-0AB0 As of V4. 24 / 24 - + + - -

As of

V4.0.5 24 / 24 - + + - +

CPU 416-2 ..416-2XK04-0AB0 As of V4. 64 / 64 + + + + -

As of V4.1 64 / 64 + + + + +

CPU 416-3 ..416-3XL04-0AB0 As of V4. 64 / 64 + + + + -

As of V4.1 64 / 64 + + + + +

CPU 416F-2 ..416-2FK04-0AB0 As of V4. 64 / 64 + + + + -

As of V4.1 64 / 64 + + + + +

2 Requirements for Use

B4-10 CP 443-5 Extended for PROFIBUS / Manual Part B4

Release 6/2005

C79000-G8976-C162-06

Table 2-1 Use with the Current CPU Types, continued

CPU Firmware versionOrder Number of the

CPU:

6ES7...

CPU

Number of AG-SEND or AG-RECV calls at

same time

Order Number of the

CPU:

6ES7...

CPU

SYNC/FREEZE functionality

Order Number of the

CPU:

6ES7...

DP-V1 functionality

CiR / HCiR functionality 1)

Activate / deactivate

DP slave

Identify bus

topology

CPU417-4 ..417-4XL04-0AB0 As of V4. 64 / 64 + + + + -

As of V4.1 64 / 64 + + + + +

CPU417-4H ..417-4HL04-0AB0 As of V4. 64 / 64 - + + - -

As of

V4.0.5 64 / 64 - + + - +

Legend:

+ => The characteristic is supported / the listed mode is possible

- => The characteristic is not supported / the listed mode is not possible

1) All CPUs are CiR capable (the H-CPUs HCiR).

Indice

Altri manuali Siemens Unità di controllo

Siemens

Siemens SIWAREX MS Guida all'applicazione

Siemens

Siemens SIRIUS ACT 3SU1400-1EK10-6AA0 Manuale utente

Siemens

Siemens SINUMERIK 840C Manuale utente

Siemens

Siemens SINUMERIK 840D Manuale elenco delle parti

Siemens

Siemens LOGO! Series Manuale utente

Siemens

Siemens SIRIUS PROFINET Manuale utente

Siemens

Siemens PN16 Manuale utente

Siemens

Siemens HARS-T03 Series Manuale utente

Siemens

Siemens 6SE7024-1EP85-0AA1 Manuale utente

Siemens

Siemens SIRIUS 3RA2712 Documento tecnico

Siemens

Siemens SITRANS FM MAG 8000 IIoT Manuale utente

Siemens

Siemens HiPath optiPoint 410 Manuale di istruzioni

Siemens

Siemens K60R Manuale utente

Siemens

Siemens SINUMERIK 808D Manuale elenco delle parti

Siemens

Siemens SINUMERIK 840Di Manuale utente

Siemens

Siemens SINAMICS G120 Guida per l'amministratore

Siemens

Siemens SIRIUS 3SB38 Manuale utente

Siemens

Siemens SIMOTION D4 Series Manuale utente

Siemens

Siemens VAI61 Series Manuale utente

Siemens

Siemens SITRANS PCS 7 Manuale elenco delle parti

Siemens

Siemens SINAMICS G130 Manuale utente

Siemens

Siemens EFB300 Manuale utente

Siemens

Siemens 3WN 6 3WX3661-0JA00 Manuale utente

Siemens

Siemens LGB21.130A17 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente