Siemens RCC-2/R Manuale utente
Installation Instructions
Model RCC-2/R and RSE-1
Remote Control Centers
INTRODUCTION
The Model RCC-2/R Remote Command Center
from Siemens Industry, Inc. (See Figure 1)
provides the option to remotely annunciate and
control MXL and MXL-IQ system status. The
RCC-2/R and RSE-1 provide for mounting and
control of the PIM-1 printer interface module.
The following modules come already installed in
an RCC-2/R:
• Keypad
• LCD Display
• ANN-1 Driver Board
• PS-5N7 Power Supply
The following modules come already installed in
an RSE-1:
• ANN-1 Driver Board
• PS-5N7 Power Supply
The RCC-2/R has a mounting location for an
optional PIM-1. The RSE-1 has the same
mounting and requires the PIM-1.
The RCC-2/R comes with a clear lens on a
secure door. This limits access to the control of
the system or the display. The door is secured
with a T-45 lock set.
OPERATION
The keypad on the RCC-2/R operates the same
as the MKB in the MXL enclosure. See Section 3
of the MXL Installation, Operation and Mainte-
nance Manual, P/N 315-092036, for the com-
plete operating instructions for the control panel.
INSTALLATION
Always remove all power before installa-
tion, first the battery and then the AC.
Setting the Network Address
Before installing the RCC/RSE, set the network
address on S1-SW1 and S1-SW2 of the ANN-1
board. Refer to Table 1 for switch settings. (See
also Setting the Network Address in Section 2,
INSTALLATION of the MXL/MXLV Manual, P/N
315-092036.)
TABLE 1
SWITCH SETTINGS ON THE ANN-1
SWITCH
ADDRESS SETTINGS FOR:
248 249 250 251
S1-SW1 Open-
OFF Closed-
ON Open-
OFF Closed-
On
S1-SW2 Open-
OFF Open-
OFF Closed-
ON Closed-
ON
S1-SW3 Closed-
ON Closed-
ON Closed-
ON Closed-
ON
S1-SW4 Closed-
ON Closed-
ON Closed-
ON Closed-
ON
S1-SW5 Closed-
ON Closed-
ON Closed-
ON Closed-
ON
NOTE: Switches S1-SW3 and S1-SW4 are for
future use. Switch S1-SW5 is used to
select supervision.
Figure 1
RCC-2/R Remote Command Center
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
P/N 315-099160-8
2
Setting Supervision
Use switch S1-SW5 on the ANN-1 to select or
deselect supervision. If your ANN-1 has a switch
with position 1 indicated on the left-hand side,
ignore the printing on the switch. SW1 on S1 is at
the extreme right-hand side of S1, regardless of
any other marking.
To set for supervision
S1-SW5 = Closed (ON)
To set for non-supervision
S1-SW5 = Open (OFF)
NOTE: When you select non-supervision for
an annunciator, there must also be
one and only one supervised annun-
ciator at the same address.
Mounting
Before mounting the RCC/RSE, follow these
steps:
1. Remove the cover assembly from the
backbox.
2. Disconnect at P1 the cable from the PS-5N7.
3. Remove the PS-5N7 from the backbox (See
Figures 2 and 3).
4. Set the panel to one side.
Consider the following when mounting the
backbox:
• Mounting height for visual and manual
access to the keypad
• Weight and size of the enclosure
• Local mounting codes
To mount the RCC/RSE, follow these steps:
1. Fasten the RCC/RSE backbox securely to a
clean, dry, shock-free, and vibration-free
surface using the four mounting holes
provided. (Refer to Figure 4 for the
dimensions of the backbox and the location
of the mounting holes.) Position the RCC/
RSE backbox clear of obstructions so that
the door opens freely and the indicators and
controls are easily accessible.
2. Pull all field wiring into the backbox and
dress the wiring to the approximate location
to which it will go. Install field wiring to the
PS-5N7 (Refer to PS-5N7 Installation
Instructions,
P/N 315-092729).
3. If a PIM-1 is required, mount it to the set of
four standoffs to the right of the PS-5N7
(See Figures 2 and 3).
Connect P1 on the PIM-1 to P1 on the ANN-1,
using the 14 inch cable, P/N 555-192242.
Connect P2 on the PIM-1 to P1 on the PS-5N7,
using the 14 inch cable, P/N 555-192242
(Refer to PS-5N7 Installation Instructions,
P/N 315-092729, PIM-1 Installation
Instructions, P/N 315-091462 and Figure 6).
4. If a PIM-1 is not installed, reconnect P1 on
the ANN-1 to P1 on the PS-5N7.
5. Reattach the cover assembly to the
backbox.
6. Refer to the MXL/MXLV Manual, P/N 315-
092036, for additional information on the
operation of the keypad.
ELECTRICAL RATINGS
Refer to the following Installation Instructions as
needed:
MMB-2 P/N 315-095097
MMB-3 P/N 315-048860
PSR-1 P/N 315-090911
PS-35 P/N 315-085062
PLM-35 P/N 315-093495
PAD-3 P/N 315-099082
SMB-2 P/N 315-095931
MXL/MXLV Manual P/N 315-092036
WIRING
tnerruCeludoMCDV5evitcAAm0
eludoMCDV42evitcA tnerruC Am51+Am56 desusi1-MIPfi
eludoMCDV42ybdnatS tnerruC Am51+Am56 desusi1-MIPfi
3
Figure 2
RCC-2/R Exploded View
LCD DISPLAY
ANNUNCIATOR
PANEL
COVER PIM-1
(OPTIONAL)
ANN-1
RCC-2/RSE-1
OUTER DOOR
RCC-2/RSE-1
BACKBOX
PS-5N7
PIM-1
(REQUIRED)
ANN-1
RSE-1 OUTER DOOR
RSE-1
BACKBOX
PS-5N7
Figure 3
RSE-1 Exploded View
4
Notes:
1. Use a minimum wire gauge of 18 AWG.
2. Use a maximum of 80 ohms per pair of
wires for the network connections.
3. Use shielded twisted pair for network
connections.
4. Terminate the shield ONLY at the MMB/SMB
enclosure.
5. PSR-1 only allowed in systems with MMB-2.
Figure 5
PS-5N7 Power Supply and Network Wiring Diagram in RCC/RSE Enclosure (Style 4)
654321
PS-5N7
(INSTALLED IN AN
RCC-2/RSE-1
ENCLOSURE)
TB1
TB4
EOLR 120 OHMS
1/4W, 5%
P/N 140-820150
DO NOT USE
DO NOT USE
PSR-1
PSR-1
TB4
NO
EOLR
CHASSIS
SHIELD
MMB-2 / SMB-2
EOLR 120 OHMS
1/4W, 5%
P/N 140-820150
NO
EOLR
Figure 4
RCC-2/R, RSE-1 Dimensions
NOTE: The RCC/RSE MUST have an earth ground connected to the chassis. Wire shield or conduit is
not an acceptable ground. Use any available unused, unpainted stud for chassis grounding.
6. DO NOT place the PS-5N7 at the end of
the network (Style 7 only).
7. This configuration is power limited to NFPA
70 according to NEC 760.
8. All wiring supervised.
9. Refer to Wiring Specification for MXL, MXL-IQ
and MXLV Systems, P/N 315-092772 revision
6 or higher, for additional wiring information.
10. MNET: Maximum voltage: 8V peak to peak
Maximum current: 150mA
5
MAKE THIS CONNECTION TO ANY
OF THE FOLLOWING TERMINATIONS:
MMB
SMB
PSR-1
PLM-35
(Used with PS-35)
ALARMSAF
(Model BN4-002-UL)
PAD-3
TB5, 9-12
TB5, 9-12
TB3, 3-6
TB1, 1-2
DC1
TB2, 18-19
MOM-4
TB1 P5
P1
TB6
PSR-1
4
3
2
1
N
E
T
W
O
R
K
TB4
P7 FOR
NET-7
1234
NET-7
P7
P6
1
1
1
N
E
T
7
M
CABLE P/N 555-190967
MMB-2 / SMB-2
1
2
3
4
5
POWER
TO MOM-4
P3
TB1
CABLE
P/N 600-290505
CHASSIS
SHIELD
SHIELD
123 4 5 6 7 8 9 10 11 12 13 14 16
15
EOLR
120 OHM,
1/4W, 5%
P/N 140-820150
NETWORK A (PRIMARY)
SUPERVISED
POWER LIMITED
NETWORK B (SECONDARY)
SUPERVISED
POWER LIMITED
+24 VDC
-24 VDC RETURN
SUPERVISED
POWER LIMITED
RCC-2 / RSE-1
6
5
4
3
2
1
PS-5N7
(INSTALLED IN AN
RCC-2/RSE-1
ENCLOSURE)
TB1
P6
TB2
Figure 6
PS-5N7 Power Supply and Network Wiring Diagram in RCC/RSE Enclosure (Style 7)
Notes:
1. Use a minimum wire gauge of 18 AWG.
2. Use a maximum of 80 ohms per pair of
wires for the network connections.
3. Use shielded twisted pair for network
connections.
4. Terminate the shield ONLY at the MMB/SMB
enclosure.
5. PSR-1 only allowed in systems with MMB-2.
6. DO NOT place the PS-5N7 at the end of
the network (Style 7 only).
7. This configuration is power limited to NFPA
70 according to NEC 760.
8. Refer to Wiring Specification for MXL, MXL-IQ
and MXLV Systems, P/N 315-092772 revision 6
or higher, for additional wiring information.
9. MNET: Maximum voltage: 8V peak to peak
Maximum current: 150mA
6
This page is intentionally blank.
7
This page is intentionally blank.
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
Siemens Building Technologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
P/N 315-099160-8
This page is intentionally blank.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Siemens Unità di controllo
Siemens
Siemens SIMATIC S7 Documento tecnico
Siemens
Siemens SINUMERIK 808D Guida all'installazione
Siemens
Siemens SINAMICS G110M Manuale utente
Siemens
Siemens Climatix POL822 Manuale utente
Siemens
Siemens SIMATIC ET 200SP IM 155-6 PN/2 HF Manuale utente
Siemens
Siemens Simatic SM331 Manuale utente
Siemens
Siemens 550-818B Manuale utente
Siemens
Siemens XDACT-ASSY Manuale utente
Siemens
Siemens IM 153-4 PN Manuale utente
Siemens
Siemens SIMATIC ET 200SP CM 1xDALI Manuale del proprietario
Siemens
Siemens SINAMICS G120 Manuale utente
Siemens
Siemens SIRIUS 8WD4428-0B Manuale utente
Siemens
Siemens ASR61EX Manuale utente
Siemens
Siemens SINUMERIK 828D Turning Manuale elenco delle parti
Siemens
Siemens SIMATIC ET 200SP Manuale utente
Siemens
Siemens REP-1 Manuale utente
Siemens
Siemens 6ES7134-4FB51-0AB0 Manuale utente
Siemens
Siemens 3RK1200-0C.03-0AA2 Manuale utente
Siemens
Siemens SIMATIC PRO Extension Units KP Series Manuale utente
Siemens
Siemens SINAMICS DCM Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
