Siemens TSM-1 Manuale utente

Fire Safety

INTRODUCTION

The Model TSM-1 Test Switch Module from Siemens

Building Technoliges, Inc. is a key activated momen-

tary switch for use with intelligent duct detectors on

the MXL System. It is used in conjunction with a TRI,

whose CSG-M usage is set to TEST. When the TRI

senses the TSM-1 switch closure, it will cause its

associated intelligent duct detector to go into alarm.

This alarm condition will cause all logic associated

with the duct detector to activate. The TSM-1 is

mounted on a switch plate and can be installed in a

single gang box.

Remove all power from the system until the

installation is complete and ready for testing.

All work of any kind shall be performed to meet

the requirements of all local and national codes

and/or standards required by the authority hav-

ing jurisdiction.

WIRING INSTRUCTIONS

Refer to the wiring diagrams in Figures 2 and 3

and wire the addressable interface module

according to the appropriate operation for your

system.

Note: The recommended wire size is as follows:

18 AWG minimum

14 AWG maximum

POWER LIMITED WIRING FOR THE TSM-1

TEST SWITCH MODULE

In compliance with NFPA70—National Electrical

Code, all power limited fire protective signaling

conductors must be separated by a minimum of ¼

inch from all of the following items located within an

outlet box:

• Electric light

• Power

• Class 1 or non-power limited fire protective

signaling conductors

INSTALLATION

1. Remove the module from its protective bag.

Mount the TSM-1 in a user supplied standard

single gang mounting box (1½ in deep is

recommended). Refer to Figure 1.

2. Terminate all field wires to the TSM-1 as required

for your application. Refer to the connection

diagrams shown in Figures 2 and 3.

3. Attach the switch frame to the box.

4. Check that jumper JP1 is NOT installed. (JP1 is

not used in this application.)

5. Attach the keyswitch connector to its mating plug

on the bottom of the circuit board.

6. Insert the face plate and attach the cover plate

with the two screws provided.

Note: A yellow and green LED are included in the

kit. Do not use them in this application.

P/N 315-098285-8

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2185 Derry Road West

Mississauga, Ontario L5N 7A6 Canada

Installation Instructions

MODELTSM-1

Test Switch Module

PROGRAMMING

1. Use the FPI-32 Programmer/Tester to program

the TRI to the desired address. Select STATUS

as the usage.

2. To operate the TSM-1 LED by the TRI-R relay

contacts:

In the CSG-M, configure the TRI by setting its

usage to TEST and assign the detector’s

address to the TRI-R.Add a logic function with

the intelligent detector that will be tested as the

input, and assign the output as the TRI-R. Refer

to Figure 2.

3. To operate the TSM-1 LED by the air duct

detectors:

In the CSG-M, configure the TRI by setting its

usage to TEST.Add a logic function with the

intelligent detector that will be tested as the

input, and assign the output as the fan shutdown

control operated by the air duct detector. Refer to

Figure 3.

Figure 1

TSM-1 Assembly

OPERATION

Reset the MXL System until SYSTEM NORMAL is

displayed on the panel. Insert the key into the

manual keyswitch input point on the TSM-1.Activate

the momentary switch by turning the key to the right.

When the TSM-1 keyswitch is activated, the super-

vised switch input of the TRI-R is closed. The TRI-R

activation is received by the MXL panel. The MXL

panel then sends a reduced alarm threshold to the

detector through the TEST usage of the TRI-R. This

causes the detector to alarm.

When the detector goes into alarm and sends alarm

data back to the MXLpanel, the MXL panel sends

command data to the TRI-R or air duct to close the

relay, which activates the fan controller through the

logic function. The MXLpanel sends a signal to the

intelligent detector, turning on the red LED in both the

detector and the TSM-1, indicating the detector is in

alarm.

Reset the system. The MXLSystem will restore the

detector’s alarm threshold and display SYSTEM

NORMAL on the panel.

CAUTION:

The TSM-1 switch does not perform all of the required smoke detector tests as speci-

fied in NFPAStandard 72. Please refer to the instructions that accompany the smoke

detector for the complete test requirements.

Figure 2

TSM-1 Interface to MXL System

TSM-1 LED operated by the TRI-R relay contacts

From MXL

ALD Loop

Earth

Ground

Switch

Input LED

TSM-1

TRI-R

End of Line Device

for TRI-R

3.6K, 1/4W,

P/N 140-820185

24 VDC @ 20mA (max)

From MMB-2, TB5

or MMB-3, TB9

Terminals 9-12

or PSR-1, TB3

Terminals 3-6

or UL Listed

Power Supply

To Air Duct

Detector or next

device on loop

Switch contact rating:

24VDC @10mA (min.)

Figure 3

TSM-1 Interface to MXL System

TSM-1 LED operated by the Air Duct Detector

NOTES:

1. For use only with Air Ducts with an incorporated relay.

2. Refer to the TRI Installation Instructions, P/N 315-096242, for specific interface module wiring requirements.

3. Refer to the AD-11PR, AD-11XPR Installation Instructions, P/N 315-095659, or the AD-3I/-3ILP Installation Instructions,

P/N 315-093234, for specific duct detector wiring requirements, as applicable.

From MXL

ALD Loop

Earth

Ground

Switch

Input LED

TSM-1

TRI-R

End of Line Device

for TRI-R

3.6K, 1/4W,

P/N 140-820185

To Air Duct Detector

(See Detector Installation

Instruction for Remote

Alarm Indicator

Connection)

To Fan

Shutdown

Control

To Air Duct Detector

or next device on loop

Switch contact rating:

24VDC @10mA (min.)

NOTES:

1. For use only with Air Ducts without an incorporated relay.

2. Refer to the TRI Installation Instructions, P/N 315-096242, for specific interface module wiring requirements.

3. Refer to the AD-11P Installation Instructions, P/N 315-095659, or the AD-3I/-3ILP Installation Instructions, P/N 315-

093234,

for specific duct detector wiring requirements, as applicable.

P/N 315-098285-8

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2185 Derry Road West

Mississauga, Ontario L5N 7A6 Canada

Altri manuali Siemens Unità di controllo

Siemens

Siemens SIMATIC FM 353 Manuale utente

Siemens

Siemens RUGGEDCOM ROS Manuale utente

Siemens

Siemens 986-88301A Manuale utente

Siemens

Siemens SIMATIC 8DO DC24V/0.5 A Manuale utente

Siemens

Siemens SZE-4X Manuale utente

Siemens

Siemens MVS661 N Series Manuale utente

Siemens

Siemens 7KM4211-1BA00-3AA0 Manuale utente

Siemens

Siemens VRD Series Manuale del proprietario

Siemens

Siemens 3AK Manuale utente

Siemens

Siemens Add 7 AddFEM Manuale utente

Siemens

Siemens SINAMICS G120 Scheda tecnica

Siemens

Siemens SINAMICS S120 Documento tecnico

Siemens

Siemens SIMATIC TI505 Manuale utente

Siemens

Siemens Flowrite 599 Series Manuale del proprietario

Siemens

Siemens WFZ56 Series Manuale di installazione e funzionamento

Siemens

Siemens SAFEDLINK Guida

Siemens

Siemens SIRIUS 3RU Series Manuale utente

Siemens

Siemens MOBY I ASM 421 Manuale elenco delle parti

Siemens

Siemens Simatic S7-1500 Manuale utente

Siemens

Siemens SIMATIC NET CP 343-2 Manuale utente

Siemens

Siemens SIMATIC ET 200SP Manuale utente

Siemens

Siemens LMV52 series Manuale utente

Siemens

Siemens K60R Manuale utente

Siemens

Siemens S7-1500 PROFIBUS Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente