Siemens SMART 7KT Manuale utente
s
Assembly Instruction
Multi-function Meter
SMART 7KT
7KT0310
Please read and understand these instructions before installing,
operating, or maintaining the equipment.
DANGER
Hazardous voltage. Will cause death or serious
injury. Turn off and lock out all power supply to
this device before working on this device.
Replace all covers before power supplying this
device is turned on.
Contents
4 nos. Terminal Clamps Rubber Gasket x1
Cross recessed Phillips head
Installation
For installing the meter
Prepare the panel cutout with proper dimensions as shown below.
FRONT PANEL DESCRIPTION OUTLINE
Dimensions (in mm)
PANEL CUTOUT
Dimensions (in mm)
Scan the QR code for more
information
2
Installation (Continued)
1. Insert unit into the panel 2. Position the clamps (as shown in the
gure) and push the same into the slots in
their respective locations.
3. Push/Slide all 4 clamps towards the panel
evenly till the lowest possible tooth of the
clamp is engaged. Ensure the meter is
properly tightened and it does not move.
Note: Terminal screw tightening torque: 0.7 N-m to 0.8 N-m (6 In-Lb to 7 In-Lb)
Mounting distance
The distance to be maintained between two meters while
mounting on a panel door should be at least 100 mm.
Installation Guidelines
1. This equipment, being built-in-type, normally becomes a
part of main control panel and in such case the terminals
do not remain accessible to the end user after installation
and internal wiring.
2. Conductors must not come in contact with the internal
circuitry of the equipment or else it may lead to a safety
hazard that may in turn endanger life or cause electrical
shock to the operator.
3. Circuit breaker or mains switch must be installed between
power source and supply terminals to facilitate power ‘ON’
or ‘OFF’ function. However this switch or breaker must be
installed in a convenient position normally accessible to
the operator.
4. Before disconnecting the secondary of the external
current transformer from the equipment, make sure that
the current transformer is short circuited to avoid risk of
electrical shock and injury.
5. The equipment shall not be installed in environmental
conditions other than those mentioned in this manual.
6. The equipment does not have a built-in-type fuse.
Installation of external fuse of rating 275V AC / 0.5Amp for
electrical circuitry is highly recommended.
7. Remove the scratch-guard from the meter display during
commissioning of the panel.
3
Connection diagram
Circuit Diagram
3 Phase 4-Wire (commonly used)
3 Ø - 4 Wire, 3 CT’S 3 Ø - 4 Wire, 3 CT’S and 3 PT’S
2) All Fuse Type: 0.5A, Class gG
Wiring Guidelines
1. To prevent the risk of electric shock, power supply to
the equipment must be kept OFF while doing the wiring
arrangement.
2. Wiring shall be done strictly according to the terminal
layout. Conrm that all connections are correct.
3. Use lugged terminals.
4. To reduce electromagnetic interference use of wires with
adequate ratings and twists of the same in equal size shall
be made with shortest connections.
5. Layout of connecting cables shall be away from any
internal EMI source.
6. Cable used for connection to power source, must have a
cross-section of 1mm2to 2.5mm2. These wires shall have
current carrying capacity of 6A.
7. Copper cable should be used (Stranded or Single core
cable).
SACHIN ENTERPRISE
These instructions do not purport to cover all details or variations in
equipment, or to provide for every possible contingency in connection
with installation, operation, or maintenance. Should additional
information be desired, please contact the local Siemens sales ofce.
The contents of this instruction manual shall not become part of or
modify any prior or existing agreement, commitment, or relationship.
The sales contract contains the entire obligation of Siemens. The
warranty contained in the contract between the parties is the sole
warranty of Siemens. Any statements contained herein do not create
new warranties or modify the existing warranty.
Trademarks - Unless otherwise noted, all names identied by ® are
registered trademarks of Siemens AG or Siemens Industry, Inc. The
remaining trademarks in this publication may be trademarks whose
use by third parties for their own purposes could violate the rights of
the owner.
Safety Precautions
All safety related codications, symbols and instructions that
appear in this operating manual or on the equipment must
be strictly followed to ensure the safety of the operating
personnel as well as the instrument.
If the equipment is not used in a manner specied by the
manufacturer it might impair the protection provided by the
equipment.
• Do not use the equipment if there is any mechanical
damage.
• Ensure that the equipment is supplied with correct
voltage.
CAUTION:
1. Read complete instructions prior to installation and
operation of the unit.
2. Risk of electric shock.
3. The equipment in its installed state must not come in
close proximity to any heating sources, oils, steam, caustic
vapors or other unwanted process by products.
For demounting the meter
Pull the arm of the sliding clamps in outward
direction (opposite to meter) and drag the
sliding clamps away from the panel.
Dis-assemble the snap tted base clamps from
the meter using a screw-driver
Push the meter from back side out of the panel
window and remove the gasket from the meter
Published by
Siemens Malaysia Sdn Bhd
Smart Infrastructure
Electrical Products (EP)
Cp Tower, 11, Jalan 16/11
46350 Petaling Jaya, Selangor
Malaysia
Subject to changes and errors.
The information given in this document only contains general
descriptions and/or performance features which may not always
specifically reflect those described, or which may undergo
modification in the course of further development of the products.
Product development is a continuous process. Consequently the data
indicated in this Operating Instructions is subject to change without
prior notice. For latest issue contact our sales ofces.
© Siemens 2022
Industry
Online
Support
Altri manuali per SMART 7KT
5
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Siemens Strumento di misura
Siemens
Siemens SITRANS F C MASSFLO MASS 2100 DI 6 Manuale utente
Siemens
Siemens CASTOMAT ION ANALOGINPUT T001 Manuale utente
Siemens
Siemens SITRANS WS100 Manuale utente
Siemens
Siemens Sitrans F Series Manuale utente
Siemens
Siemens SITRANS FUP1010 Manuale utente
Siemens
Siemens SIWAREX WL230 BB-S SA Manuale utente
Siemens
Siemens WSM5 Series Manuale utente
Siemens
Siemens SITRANS F Istruzioni operative
Siemens
Siemens Clinitek Advantus Manuale utente
Siemens
Siemens SENTRON 5TT7 Guida utente
Siemens
Siemens SENTRON PAC3200T Manuale utente
Siemens
Siemens SIWAREX WL230 BB-S SA Manuale utente
Siemens
Siemens SITRANS F Manuale utente
Siemens
Siemens SIPART PS100 Manuale utente
Siemens
Siemens 546-00303A Manuale utente
Siemens
Siemens SICAM Q200 7KG97 Manuale utente
Siemens
Siemens SIRIUS 3RR2143 A.30 Series Manuale utente
Siemens
Siemens SITRANS F Manuale utente
Siemens
Siemens LDS 6 Manuale utente
Siemens
Siemens ADVIA 1800 Manuale
