SIGLENT SDS2352X-E Manuale utente
Copyright and Declaration
Copyright
SIGLENT TECHNOLOGIES CO., LTD. All Rights Reserved.
Trademark Information
SIGLENT is the registered trademark of SIGLENT TECHNOLOGIES CO., LTD.
Declaration
SIGLENT products are protected by patent law in and outside of the P.R.C.
SIGLENT reserves the right to modify or change parts of or all the specifications or
pricing policies at company’s sole decision.
Information in this publication replaces all previously corresponding material.
Any way of copying, extracting or translating the contents of this manual is not
allowed without the permission of SIGLENT.
Product Certification
SIGLENT guarantees this product conforms to the national and industrial standards
in China and other international standards. Conformance certification is in
progress.
Contact Us
If you have any problem or requirement when using our products, please contact
SIGLENT TECHNOLOGIES CO., LTD
Add：3//F, Bldg No.4, Antongda Industrial Zone, 3rd Liuxian Road, Bao’an District,
Shenzhen, 518101, P.R.China
Tel：400-878-0807
E-mail：sales@siglent.com
http://www.siglent.com
Introduction
This user manual includes important safety and installation information related to
the SDS2000X-E series oscilloscopes and includes simple tutorials for basic
operation of the oscilloscope.
The series includes the following models:
Model
Analog Bandwidth
SDS2352X-E
350 MHz bandwidth, 2-channel, 2 GSa/s Sample rate
SDS2202X-E
200 MHz bandwidth, 2-channel, 2 GSa/s Sample rate
SDS2102X-E
100 MHz bandwidth, 2-channel, 2 GSa/s Sample rate
Safety Information
Measurement Category
Measurement Categories
This oscilloscope can make measurements in other circuits that are not directly
connected to mains.
WARNING
This oscilloscope can only be used for measurements within its specified
measurement categories.
Not to use the product for measurements within other measurement
categories, such as CAT II, CAT III, CAT IV.
Do not use the equipment for measurements on mains circuits.
Measurement Category Definitions
Measurement category II is for measurements performed on circuits directly
connected to the low voltage installation. Examples are measurements on
household appliances, portable tools and similar equipment.
Measurement category III is for measurements performed in the building
installation. Examples are measurements on distribution boards, circuit-breakers,
wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the
fixed installation, and equipment for industrial use and some other equipment, for
example. Stationary motors with permanent connection to the fixed installation.
Measurement category IV is for measurements performed at the source of the
low-voltage installation. Examples are electricity meters and measurements on
primary over current protection devices and ripple control units.
General Safety Summary
Carefully read the following safety precautions to avoid any personal injury or
damage to the instrument and any products connected to it. To avoid potential
hazards, please use the instrument as specified.
Use Proper Power Line
Only the power cord designed for the instrument and authorized by the local
country should be used.
Ground the Instrument
The instrument is grounded through the protective earth conductor of the power
line. To avoid electric shock, please make sure the instrument is grounded correctly
before connecting its input or output terminals.
Connect the Signal Wire Correctly
The potential of the signal wire is equal to the earth, so do not connect the signal
wire to a high voltage.
Look Over All Terminals’ Ratings
To avoid fire or electric shock, please look over all ratings and read the instructions
for the instrument. Before connecting the instrument, please read the manual
carefully to gain more information about important ratings.
Use Proper Overvoltage Protection
Make sure that no overvoltage (such as that caused by a thunderstorm) can reach
the product, or else the operator might expose to danger of electrical shock.
Electrostatic Prevention
Operate in an electrostatic discharge protective area environment to avoid
damages induced by static discharge. Always ground both the internal and
external conductors of the cable to release static before connecting.
Keep Well Ventilation
Inadequate ventilation may cause an increasing in operting temperature, which
will eventually damage the instrument. So keep well ventilation and inspect the
intake and fan regularly.
Avoid Circuit or Components Exposed
Do not touch exposed contacts or components when the power is on.
Use proper Fuse
Use only the specified fuse.
Do Not Operate Without Covers
Do not operate the instrument with covers or panels removed.
Do Not Operate With Suspected Failures.
If you suspect damage occurs to the instrument, have it inspected by qualified
service personnel before further operations. Any maintenance, adjustment or
replacement especially to circuits or accessories must be performed by SIGLENT
authorized personnel.
Do Not Operate in Wet Conditions.
In order to avoid short circuiting to the interior of the device or electric shock,
please do not operate in a humid environment.
Do Not Operate in an Explosive Atmosphere.
In order to avoid damages to the device or personal injuries, it is important to
operate the device away from an explosive atmosphere.
Keep Product Surfaces Clean and Dry.
To avoid the influence of dust and/or moisture in air, please keep the surface of the
device clean and dry.
Handling Safety
Please handle with care during transportation to avoid damaging buttons, knob
interfaces and other parts on the panels.
Only probe assemblies which meet the manufacturer’s specifications shall be used.
When using SIGLENT probe assemblies, the probe assemblies shall be insulated
from the measured circuits by double or reinforced insulation.
All probe assemblies should meet the requirements of UL 61010-031 and
CAN/CSA-C22.2 No. 61010-031-07.
Do not position the equipment so that it is difficult to disconnect an attached device
(detachable plug).
If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.
Safety Terms and Symbols
Terms in this Manual. These terms may appear in this manual:
WARNING
Warning statements indicate the conditions or practices that
could result in injury or loss of life.
CAUTION
Caution statements indicate the conditions or practices that
could result in damage to this product or other property.
Terms on the product. These terms may appear on the product:
DANGER Indicates direct injuries or hazards that may happen.
WARNING Indicates potential injuries or hazards that may happen.
CAUTION Indicates potential damage to the instrument or other property that may
happen.
Symbols on the product. These symbols may appear on the product:
Hazardous protective Earth Warning Test Power Switch
Voltage Terminal Ground
If find such symbols on the product, consult the manual to find out the nature of the
potential hazard and the actions which have to be taken.
Working Environment
Environment
This instrument is intended for indoor use and should be operated in a clean, dry
environment.
Temperature
Operating: 0℃to +40℃
Non-operation:-20℃to +60℃
Note: Direct sunlight, radiators, and other heat sources should be taken into
account when assessing the ambient temperature.
Humidity
Operating: 85% RH, 40 ℃, 24 hours
Non-operating: 85% RH, 65 ℃, 24 hours
Altitude
Operating: less than 3 Km
Non-operation: less than 15 Km
Installation (overvoltage) Category
This product is powered by mains conforming to installation (overvoltage) category
II.
WARNING
Make sure that no overvoltage (such as that caused by thunderbolt) can
reach the product, or else the operator might expose to danger of
electric
shock.
Installation (overvoltage) Category Definitions
Installation (overvoltage) category I refers to signal level which is applicable to
equipment measurement terminals connected to the source circuit. In these
terminals, precautions are done to limit the transient voltage to the corresponding
low level.
Installation (overvoltage) category II refers to the local power distribution level
which is applicable to equipment connected to the AC line (AC power).
Degree of Pollution
The oscilloscopes may be operated in environments of Pollution Degree II.
Note: Degree of Pollution II refers to a working environment which is dry and
non-conductive pollution occurs. Occasional temporary conductivity caused by
condensation is expected.
IP Rating
IP20 (as defined in IEC 60529).
Ventilation Requirement
This oscilloscope uses a fan to force cooling. Please make sure that the air intake
and exhaust areas are free from obstructions and have free air. When using the
oscilloscope in a bench-top or rack setting, provide at least 10 cm clearance beside,
above and behind the instrument for adequate ventilation.
WARNING
Inadequate ventilation may cause temperature increase which would
damage the instrument. So please keep the instrument well ventilated
during operation and inspect the intake and fan regularly.
Altri manuali per SDS2352X-E
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali SIGLENT Strumento di misura
SIGLENT
SIGLENT CP6000 Series Manuale utente
SIGLENT
SIGLENT SHS800X Series Manuale utente
SIGLENT
SIGLENT SM06035-E01A Manuale utente
SIGLENT
SIGLENT CPL5100 Manuale utente
SIGLENT
SIGLENT SSA3021X Manuale utente
SIGLENT
SIGLENT SNA5000A Manuale utente
SIGLENT
SIGLENT SSA3000X Series Manuale utente
SIGLENT
SIGLENT SHA800A Manuale utente
SIGLENT
SIGLENT SHA852A Manuale utente
SIGLENT
SIGLENT SSA5000A Manuale utente
SIGLENT
SIGLENT SHA850A Manuale utente
SIGLENT
SIGLENT SSA3000X-R Manuale utente
SIGLENT
SIGLENT SVA1000X Series Manuale utente
SIGLENT
SIGLENT SSA3075X Plus Manuale utente
SIGLENT
SIGLENT SSA5085A Manuale utente
SIGLENT
SIGLENT SVA1075X Manuale utente
SIGLENT
SIGLENT SNA5000A Manuale utente
SIGLENT
SIGLENT SSA3000X Plus Manuale utente
SIGLENT
SIGLENT SP3150A Manuale utente
SIGLENT
SIGLENT SSA3050X-R Manuale utente
