SIGMA TEK SCP 111 Manuale utente

SCP 111

S-DIAS Safety CPU Module

Date of creation: 20.05.2015

Version date: 04.11.2020

Article number: 20-890-111-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation from German

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsible

for technical or printing errors in the handbook and assumes no responsibility for damages that occur through use

of this handbook.

S-DIAS SAFETY CPU MODULE SCP 111

04.11.2020 Page 1

S-DIAS Safety CPU Module E SCP 111

The S-DIAS Safety CPU module supports up to 16 Safe IO modules. In

addition, the SCP 111 can operate handheld devices with Emergency Stop

and/or confirmation buttons.

The Safety CPU component has the safety integrity level SIL3 or SIL CL

3(EN / IEC 62061) or Performancelevel e (PL e) (EN ISO 13849-1/-2).

The safety-related SCP 111 is ideal for use in systems with optional

modules and interface variables according to Safety System Handbook,

see homepage

With the SCP 111, Safe process data is transmitted with its own safety

protocol (FSoE). Therefore, the SCP 111 cannot be used with a CSCP

011/012, SCP 010/011 in a Safety project.

The SCP 111 alone is already a minimal system of a safety control.

In addition, the Safety SCP 111 regulates the synchronized communication

with the remote safety modules through safe bus telegrams. Included

among their jobs are:

•Processing the safe application and

•The distribution of configuration data to remote safety modules

Using the search function with the keyword “Safety System Handbook”

SCP 111 S-DIAS SAFETY CPU MODULE 
 
Page 2 04.11.2020 
Contents 
1Basic Safety Guidelines......................................................... 5 
1.1 General Safety Information..........................................................5 
1.2 Further Safety Guidelines............................................................6 
1.3 General Requirements .................................................................7 
2Safety Conformity..................................................................11 
2.1 Functional Safety Standards.....................................................11 
2.2EU Conformity Declaration........................................................11 
2.3 Safety-Relevant Parameters......................................................12 
2.3.1 Mounting Position Horizontal 0-55 °C Ambient Temperature ............12 
2.3.2 Mounting Position Horizontal 55-60 °C Ambient Temperature ..........12 
2.4 Compatibility...............................................................................13 
3Technical Data .......................................................................14 
3.1 Performance Data.......................................................................14 
3.2 Electrical Requirements.............................................................14 
3.2.1 Module Supply (Input) .......................................................................14 
3.2.2 S-DIAS Bus/Safety Supply (Output)..................................................15 
3.3 Miscellaneous .............................................................................18 
3.4 Environmental Conditions.........................................................18 
4Mechanical Dimensions........................................................19 
5Connector Layout..................................................................20 
5.1 Status LEDs.................................................................................21 

 S-DIAS SAFETY CPU MODULE SCP 111 
 
11.2020 Page 3 
2 Applicable Connectors...............................................................22 
3 Label Field ...................................................................................23 
6Validation Button...................................................................24 
1 Explanation of the Individual Sequences.................................24 
1.1 Start Sequence................................................................................. 24 
1.2 Command Selection Sequence......................................................... 25 
1.3 End Sequence .................................................................................. 25 
1.4 Error Sequence................................................................................. 26 
2 Overview of Commands.............................................................27 
3 Overview of Module Status and Commands............................27 
4 Handling the microSD Card.......................................................29 
5 Configuring a Safety CPU with the SD Card............................30 
7Error Response .....................................................................32
1 Restart Errors..............................................................................32 
2 Configuration Distribution Error ...............................................33 
3 Troubleshooting..........................................................................34 
4 Troubleshooting with the SafetyDesigner ...............................34 
5 Correcting a Wiring Error...........................................................34 
8Wiring Guidelines..................................................................35 
9Mounting................................................................................36 
Supported Cycle Times ........................................................38 
1 Cycle Times below 1 ms (in µs).................................................38 

SCP 111 S-DIAS SAFETY CPU MODULE 
 
Page 4 04.11.2020 
2 Cycle Times equal to or higher than 1 ms (in ms) ..................38 
Disposal..................................................................................38
Hardware Class SCP111........................................................39 
1 General.........................................................................................40 
2 Safety...........................................................................................41 
3 Communication Interfaces.........................................................43 
4 Global Methods...........................................................................44 
4.1 FetchDiagState..................................................................................44 
4.2 GetDiagState.....................................................................................44 
4.3 FetchDiagInfo....................................................................................44 
4.4 GetDiagInfo .......................................................................................44 
4.5 SaveLog ............................................................................................45 
4.6 SaveLogActive...................................................................................45 
5 Importance of ClassState and SafetyState ..............................46 
5.1 Example.............................................................................................46 
6 Internal Properties......................................................................46 
7 Transmission of Safe Signals over Several Machines or 
Machine Parts .............................................................................47 
7.1 When to use interface connections and when to use FlexCon?........48 
7.2 Interface Connection .........................................................................49 
7.3 Safety Hot Swap (FlexCon Connection)............................................54 
 

S-DIAS SAFETY CPU MODULE SCP 111

04.11.2020 Page 5

1 Basic Safety Guidelines

1.1 General Safety Information

If the safety guidelines are not followed, danger to personnel can arise that could lead to

serious injury or in worst cases, death. In less serious cases, systems and equipment can be

damaged.

The following symbols identify the individual risks as well as the degree of seriousness; their

respective meanings are briefly explained. You should therefore familiarize yourself with the

safety symbols and their meanings to prevent dangers and risks.

DANGER

Identifies an immediate danger with high risk, which

can lead to immediate death or serious injury if not

avoided.

Indique un danger direct à haut risque d’un décès

immédiat ou des blessures graves si les consignes de

sécurité ne sont pas respectées.

WARNING

Identifies a possible danger with a mid-level risk, which

can lead to death or (serious) injury if not avoided.

Indique un danger possible d’un risque moyen de

décès ou de (graves) blessures si les consignes de

sécurité ne sont pas respectées.

CAUTION

Identifies a low risk danger, which can lead to injury or

property damage if not avoided.

Indique un danger avec un niveau de risque faible des

blessures légères ou des dommages matériels si les

consignes de sécurité ne sont pas respectées.

SCP 111 S-DIAS SAFETY CPU MODULE

Page 6 04.11.2020

1.2 Further Safety Guidelines

Warning, dangerous electrical voltage

Avertissement d’une tension électrique dangereuse

Hot surface warning

Avertissement d’une surface chaude

Danger for ESD-sensitive components

This symbol identifies important or additional

information regarding the operation of the safety

modules.

Ce symbole indique des informations importantes ou

supplémentaires concernant le fonctionnement des

modules de sécurité particuliers.

S-DIAS SAFETY CPU MODULE SCP 111

04.11.2020 Page 7

1.3 General Requirements

Technical

Documentation

This technical documentation is a component of this product.

•This document must be accessible in the vicinity of the

machine, since it contains important instructions.

•The technical documentation should be included in the

sale, rental or transfer of the product.

Documentation

technique

Cette documentation technique fait partie intégrale du produit.

•Gardez la toujours à portée de main et à la proximité de

la machine, car elle contient des informations

importantes.

•Distribuez la documentation technique aux secteurs de

la vente et/ou de la location du produit.

Acceptance of Safety

Guidelines

Before handling the product to which this documentation

belongs, the operating instructions and safety guidelines mustbe

read. SIGMATEK GmbH & Co KG accepts no liability for

damages resulting from non-compliance with the safety

guidelines or the relevant regulations

Acceptance of the safety guidelines and the explanations in this

document, as well as the Safety System handbook are a basic

requirement for proper use. Therefore, read this operating

manual thoroughly and familiarize yourself with each of them in

detail.

More information on standards and regulations etc. can be found

in the system handbook

Prendre connaissance

de consignes de

sécurité

Avant toute manipulation on doit impérativement prendre

connaissance de consignes de sécurité et du mode d’emploi.

SIGMATEK GmbH & Co KG n'assume aucune responsabilité

pour les dommages causés par le non-respect des consignes de

sécurité ou du mode d’emploi respectif.

La connaissance de consignes de sécurité et le contenu de cette

documentation ainsi que le mode d’emploi du système de

sécurité constitue une condition préalable à l'utilisation prévue.

Lisez ce mode d’emploi et assurez-vous de le comprendre

jusqu’aux détails.

Pour plus d'informations sur les normes et les lignes directrices,

etc., reportez-vous au mode d’emploi.

SCP 111 S-DIAS SAFETY CPU MODULE

Page 8 04.11.2020

Qualified Personnel

Installation, assembly, programming and initial start-up,

operation, maintenance and decommissioning of control and

automation technology products in general, as well as safety-

related products especially, can only be performed by qualified

personnel.

Qualified personnel in this context are people, who have

completed training or have trained under supervision of qualified

personnel and have been authorized to operate and maintain

safety-related equipment, systems and facilities in compliance

with the strict guidelines and standards of safety technology.

Personnel qualifié

Installation, montage, programmation, mise en service,

l'exploitation, l'entretien et mise hors service de produits de

commande et d'automatisation en général, et de produits liés à

la sécurité, en particulier, ne peut être effectuée que par le

personnel qualifié.

On entend sous terme personnel qualifié les personnes ayant

acquis une formation professionnelle dispensé parun spécialiste

sur l’utilisation et surveillance des composants et des systèmes

de sécurité, ceci conformément aux lignes directrices et les

normes en vigueur.

Altri manuali per SCP 111

Indice

Altri manuali SIGMA TEK Unità di controllo

SIGMA TEK

SIGMA TEK AM 441 Manuale utente

SIGMA TEK

SIGMA TEK AO 046 Manuale utente

SIGMA TEK

SIGMA TEK HZS 7321 Manuale utente

SIGMA TEK

SIGMA TEK CP 112-1 Manuale utente

SIGMA TEK

SIGMA TEK SAI 041 Manuale utente

SIGMA TEK

SIGMA TEK STO 081 Manuale utente

SIGMA TEK

SIGMA TEK SCP 011 Manuale utente

SIGMA TEK

SIGMA TEK EZ 101 Manuale utente

SIGMA TEK

SIGMA TEK EZ 102 Manuale utente

SIGMA TEK

SIGMA TEK SCP 211 Manuale utente

SIGMA TEK

SIGMA TEK AI 0812 Manuale utente

SIGMA TEK

SIGMA TEK CP 102 Manuale utente

SIGMA TEK

SIGMA TEK SRO 021 Manuale utente

SIGMA TEK

SIGMA TEK STO 081 Manuale utente

SIGMA TEK

SIGMA TEK CSDI 162 Manuale utente

SIGMA TEK

SIGMA TEK MDP 102-1 Manuale utente

SIGMA TEK

SIGMA TEK PL 221 Manuale utente

SIGMA TEK

SIGMA TEK SCP 111-S Manuale utente

SIGMA TEK

SIGMA TEK HMI-Link G2 Device Manuale utente

SIGMA TEK

SIGMA TEK KL 090 Manuale utente

SIGMA TEK

SIGMA TEK TO 161 Manuale utente

SIGMA TEK

SIGMA TEK AM 222 Manuale utente

SIGMA TEK

SIGMA TEK SCP 011 Manuale utente

SIGMA TEK

SIGMA TEK CP 112 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente