SIIG JJ-E02111-S1 Manuale utente
1
04-0719B
2-Port RS232 Serial
PCIe with 16950 UART
Quick Installation Guide
Introduction
The 2-Port RS232 Serial PCIe with 16950 UART is
a high-speed serial card that provides two
additional serial ports to your system.
Key Features and Benefits
• PCI Express (x1) single port serial with 128-
byte FIFO buffers
• Works in any available PCI Express slot
• Supports data transfer rate up to 230Kb/s
• Built-in 16C950 compatible UART
System Requirements
•PCI Express equipped system with an
available PCI Express slot
•Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000
2
PackageContents
•2-Port RS232 Serial PCIe with 16950 UART
• Driver CD
• Quick installation guide
Layout
Figure 1: Layout
Stripe
Serial port pin
header (P1)
Serial port pin header (P2)
Connector bracket with 9-pin serial port
3
Hardware Installation
General instructions for installing the card are
provided below. Since the design of computer
cases and motherboards vary, refer to your
computer’ s reference manual for further
information, if needed.
Static Electricity Discharge may permanently
damage your system. Discharge any static
electricity build up in your body by touching your
computer’ s case for a few seconds. Avoid any
contact with internal parts and handle cards
only by their external edges.
1. Turn OFF the power to your computer and
any other connected peripheral devices.
2. Unplug the power cord and remove the
cover from the computer.
3. Remove the slot bracket from an available
PCIe slot.
4. To install the card, carefully align the card's
bus connector with the selected PCIe slot on
the motherboard. Push the board down
firmly, but gently, until it is well seated.
4
5. Replace the slot bracket's holding screw to
secure the card.
6. Replace the computer cover and reconnect
the power cord.
Driver Installation
Follow the instructions below to install the 2-Port
RS232 Serial PCIe with 16950 UART drivers.
Windows 8 (32-/64-bit) / 7 (32-/64-bit) /
Server 2008 R2
1. Install the board and boot up Windows.
Note: Windows 7 will automatically search
preconfigured driver folders for the proper
driver,thisprocessmay takeseveral minutes
to complete. Do not interrupt this process.
2. Insert the driver CD. Close AutoPlay if
prompted.
3. Click Start. In the Search programs and
files box, type D:\setup.exe, press Enter.
Or press Windows key and R, type
D:\setup.exe, click OK. (Change D: to
match your CD/DVD-ROM drive letter)
5
4. At the User Account Control, click Yes.
Skip this step if not prompted.
5. At the Welcome to the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Setup Wizard, click Install.
6. At the Completing the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Wizard,select Reboot now, then click Finish
to complete the installation.
Windows Vista (32-/64-bit) / Server 2008
(32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware window,
click Cancel.
3. Insert the driver CD. Close AutoPlay if
prompted.
4. Click Start. In the Start Search box, type
D:\setup.exe, press Enter. (Change D: to
match your CD/DVD-ROM drive letter)
5. At the User Account Control, click Allow.
Skip this step if not prompted.
6
6. At the Welcome to the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Setup Wizard, click Install.
7. At the Completing the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Wizard,select Reboot now, then click Finish
to complete the installation.
Windows XP (32-/64-bit) / Server 2003
(32-/64-bit)
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD. Close AutoPlay if
prompted.
4. Click Start, Run. Type D:\setup.exe, click
OK. (Change D: to match your CD/DVD
ROM drive letter)
5. At the Welcome to the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Setup Wizard, click Install.
7
6. At the Completing the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Wizard,selectReboot now, then clickFinish
to complete the installation.
Windows 2000
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, click
Cancel.
3. Insert the driver CD. Close AutoPlay if
prompted.
4. Click Start, Run. Type D:\setup.exe, click
OK. (Change D: to match your CD/DVD
ROM drive letter)
5. At the Welcome to the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Setup Wizard, click Install.
6. At the Completing the OXFORD
OXPCIe952 Serial/Parallel PCIe Card
Wizard,selectReboot now, then clickFinish
to complete the installation.
8
To Verify Windows Installation
1. Check in Device Manager to verify
installation.
For Windows 8 / 7: Right click Computer,
click Manage, then click Device Manager.
For Windows Vista: Right click Computer,
click Manage, click Continue, then click
Device Manager.
For Windows XP / Server 2003 / 2000: Right
click My Computer, click Manage, click
Device Manager.
For Windows Server 2008 / Server 2008 R2:
Right clickComputer, clickManage, double
click Diagnostics, then click Device
Manager.
2. Click on the +(plus sign) in front of Ports
(COM & LPT), and a two PCI Express
UART Port ... should be displayed.
9
Changing Serial Port Number
Some serial port devices need a specific
communicationport in order to functionproperly.
If your communication port device works, do not
make any changes.
1. Right click My Computer, click Manage,
then click Device Manager.
2. Click on the + (plus sign) in front of Ports
(COM & LPT), double click the PCI Express
UART Port.
3. Click the Settings tab.
4. Click the down arrow next to the COM Port
Number to Use box. Select a communication
port that is not in use, then click OK.
5. Restart your system to take effect.
10
Blank Page
Indice
Altri manuali SIIG Hardware per computer
SIIG
SIIG CE-ED0011-S1 Manuale utente
SIIG
SIIG DP FireWire 800 3-Port PCIe Manuale utente
SIIG
SIIG NN-PC8312-S2 Manuale utente
SIIG
SIIG US2273 Manuale utente
SIIG
SIIG SC-SAE312-S3 Manuale utente
SIIG
SIIG JU-91RW12-S4 Manuale utente
SIIG
SIIG DP FireWire 800 PCIe Manuale utente
SIIG
SIIG Low Profile POS 2000RJ Manuale utente
SIIG
SIIG JU-2NE012 Manuale utente
SIIG
SIIG CyberSerial ExpressCard Manuale utente
SIIG
SIIG CyberParallel ExpressCard Manuale utente
SIIG
SIIG UltraATA 100 Pro Manuale utente
SIIG
SIIG JU-PCM422-S2 Manuale utente
SIIG
SIIG Dual Profile Hi-Speed USB 4-Port PCI Manuale utente
SIIG
SIIG Parallel Pro Manuale utente
SIIG
SIIG Parallel PCI 1P Manuale utente
SIIG
SIIG ExpressCard/54 CF R/W Manuale utente
SIIG
SIIG USB 2.0 5-Port PCI Manuale utente
SIIG
SIIG Cyber PCI I/O Manuale utente
SIIG
SIIG SATA II PCIe RAID Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
