SIIG Satellite Speaker Mounts Manuale utente
1
Satellite Speaker
Mounts - 1 Pair
Quick Installation Guide
04-0600B
Introduction
The Satellite Speaker Mounts - 1 Pair are fully-adjustable (Tilt,
Swivel, & Pivot) speaker wall or ceiling mounts.
Key Features and Benefits
• Universal design fits most speaker brands & designs
• Ceiling or wall mountable & compatible with 1, 2, or
4-hole and key-hole speaker mounting (with included
adapters)
• Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning
• Holds speakers weighing up to 8 lbs
Serial Number Sticker
For future product return or exchange, this serial number is
required. Please keep it for your reference.
2
Package Contents
• (2) Speaker mounts
• (2) 1-hole adapters
• (2) 2/4-hole adapters
• (2) 2 ¼” ceiling mount extensions
• Mounting hardware
• Quick installation guide
Mounting Hardware
M6x20mm Machine Screw
M5 x 20mm Machine Screw
8-32 x 5/8" Machine Screw
1/4"-20 x 1/2" Machine Screw
M5 x 1/8" Plastic Screw
8-32 Hex Key Hole Nut
#8 x 3/4" Self Tapping Screw
#12 x 3/4" Self Tapping Screw
#12 x 1 3/4" Self Tapping Screw
#12-14 Alligator Anchor
M4 x 8mm Flat Head Machine Screw
3
Installation
Pleasereadtheinstructionspriortoinstallation. Thisspeaker
mount is designed solely for the mounting of small speakers
weighing less than 8lbs. We are not responsible for damage
that may occur if speakers weighing more than 8lbs. are
used.
The user will have to determine which type of configuration
will work best with the included mounting hardware. If the
included hardware does not fit with the application, the
appropriate hardware will have to be purchased.
Single Hole Mounting
1. Most satellite speakers will require the use of the
M5 x 20mm machine screw used in combination with
M5 x 1/8" plastic washer. The plastic washer is used as
a spacer between the threaded insert and the post, see
Figure 1 below. It is critical the plastic washer is used
correctly.
M5 x 20mm
Machine Screw
Mounting Post
M5 x 1/8"
Plastic Washer
Back Speaker
Figure 1
4
2. Once the proper configuration is determined, secure
the post to the speaker.
3. Some speakers use the smaller M4 x 8 screw, which is
inserted into the off-center on the mounting post, see
Figure 2 below.
4. Check the size of the hole, make sure you have the
8-32 x 5/8" machine screw, the 1/4"-20 x 1/2" machine
screw, the M6 x 20mm, or the M5 x 20mm fits inside,
see Figure 3 below.
Figure 3
Figure 2
M4 x 8mm Flat Head
Machine Screw
Back Speaker
M5 x 1/8" Plastic Washer
1/4"-20 x 1/2" Machine Screw
8-32 x 5/8" Machine Screw
Back Speaker
5
5. When the correct size is determined, place the screw
through the speaker post and attach to the rear of the
speaker enclosure. If the screw does not tighten
properly, use the M5 x 1/8" plastic washer to tighten
it up.
Key Hole Mounting
1. If your speaker has a factory key hole design, you will
use the 8-32 x 5/8" machine screws in combination
with the 8-32 Hex Key Hole Nut.
2. Loosely pre-assemble the mounting post with the
8-32 x 5/8" machine screw and hex key hole nut, see
Figure 4 below.
M5 x 1/8"
Plastic Washer
8-32 x 5/8"
Machine Screw
Mounting Post
Keyhole
Back Speaker
Figure 4
8-32 Hex Key Hole Nut
6
3. Engage the hex key hole nut into the key hole slot.
4. Put tension on the assembly by gently pulling back on
the speaker mount post while tightening the
8-32 x 5/8" machine screw, see Figure 4 on page 5.
5. The hex key hole nut will engage on the housing in the
key hole slot.
6. If the post does not tighten securely against the
housing, it will be necessarry to use the M5 x 1/8"
plastic washer as a spacer under the head of the
8-32 x 5/8" machine screw, see Figure 4 on page 5.
2/4 Hole Mounting
1. Find the best mounting configuration that matches
your speaker enclosure. Four-hole mount patterns
can be accomodated by positioning the speaker plate
diagonally, see Figure 5 on the next page.
2. Using the 1/4"-20 x 1/2" machine screws, install the
speaker plate and secure the speaker enclosure, see
Figure 5 on the next page.
7
1/4"-20 x 1/2"
Machine Screw
4-Hole
Orientation
2-Hole Orientation
Figure 5
Back
Speaker
Self-Tapped Mounting
1. Locate the optimum location for the mounting plate
and use it as template to mark the drilling locations.
Do not drill or screw into the speaker where you could
possibly damage the internal components.
2. Drill the pilot hole(s) using a 1/8" drill bit. The holes(s)
should not be drilled more than 1/2" depth, see Figure
6 on the next page.
8
Back Speaker #12 x 3/4" Self
Tapping Screw
Figure 6
Mounting to the Wall or Ceiling
The mounting hardware for the three different surface
applications is supplied. You will need to determine what
style hardware will work best with your mounting surface.
Always use caution when drilling into a wall or ceiling. Make
sure to avoid all electrical and water lines.
Wood Surface
1. Using a stud finder, locate the wood stud or framing
member. Always mount the speakers in the center of
a stud.
2. Using the wall plate as a template, mark hole positions
onmountingsurface. Forin-wallapplications,position
the mounting holes in a vertical pattern, see Figure 7
on the next page.
9
#12 x 1 3/4" Self
Tapping Screw
Figure 7
3. Drill holes through the drywall and into the wood
studusinga1/8"drillbit. Theseholes shouldbe drilled
1 1/2" deep, see Figure 7 above.
4. After the holes are drilled, mount the wall plate using
the self tapping screws.
Drywall Surfaces
1. Locate the best mounting location in the ceiling or
wall. Using the wall plate as a template, mark the hole
positions on the mounting surface. For in-wall
applications, position the mounting holes in a vertical
pattern, see Figure 8 on the next page.
2. Drill holes in the drywall using a 5/16" drill bit.
3. Once the holes are drilled, insert the alligator anchor
into the holes. Make sure the anchor is flush with the
wall and/or ceiling surface, see Figure 8 on the next
page.
10
4. With the anchors in place, mount the wall plates using
the #12 x 3/4" self tapping screws, see Figure 8 below.
Figure 8
#12 x 3/4" Self
Tapping Screw
Insert screw through wall plate
and into the alligator anchor
Insert Alligator
Anchor
Pre Drill 5/16"
Holes
Concrete Surface
1. Using the wall plate as a template, mark hole positions
on the mounting surface. For in-wall applications,
position the mounting holes in a vertical pattern, see
Figure 9 on the next page.
2. Drill holes in the solid concrete or hollow block using
a 5/16" masonry bit. Once the holes are drilled, insert
the # 12-14 alligator anchors into the holes and make
sure the anchor is flush with the surface of the wall, see
Figure 9 on the next page.
Altri manuali per Satellite Speaker Mounts
1
Indice
Altri manuali SIIG Altoparlanti
