SIIG Satellite Speaker Mounts Manuale utente
1
Satellite Speaker
Mounts - 1 Pair
Quick Installation Guide
04-0600A
Introducing the Satellite Speaker
The Satellite Speaker Mounts - 1 Pair are fully-adjustable
(Tilt, Swivel, & Pivot) speaker wall or ceiling mounts.
KeyFeaturesandBenefits
• Universaldesignfitsmostspeakerbrands&designs
• Ceiling or wall mountable & compatible with 1, 2,
or 4-hole and key-hole speaker mounting (with
includedadapters)
• Allows customizable tilt, swivel, & pivot angle
adjustments for optimal speaker positioning
• Holds speakers weighing up to 8 lbs
SerialNumberSticker
Forfutureproductreturnorexchange,thisserialnumber
is required. Please keep it for your reference.
2
PackageContents
• (2) Speaker mounts
• (2) 1-hole adapters
• (2) 2/4-hole adapters
• (2) 2 ¼” ceiling mount extensions
• Mounting hardware
• Quickinstallationguide
MountingHardware
M6x20mm Machine Screw
M5 x 20mm Machine Screw
8-32 x 5/8" Machine Screw
1/4"-20 x 1/2" Machine Screw
M5 x 1/8" Plastic Screw
8-32 Round Key hole Nut
#8 x 3/4" Self Tapping Screw
#12 x 3/4" Self Tapping Screw
#12 x 1-3/2" Self Tapping Screw
#12-14 Alligator Anchor
M4 x 8mm Flat Head Machine Screw
3
Installation
Please read the instructions prior to installation. This
speaker mount is designed solely for the mounting of
small speakers weighing less than 8lbs. We are not
responsible for damage that may occur if speakers
weighing more than 8lbs. are used.
Theuserwillhavetodeterminewhichtypeofconfiguration
will work best with the included mounting hardware. If
the included hardware does not fit with the application,
the appropriate hardware will have to be purchased.
Single Hole Mounting
1. Most satellite speakers will require the use of the
M5 x 20mm machine screw used in combination
with M5 x 1/8" plastic washer. The plastic washer
isusedasaspacerbetweenthethreadedinsertand
thepost,seeFigure1below. Itiscriticaltheplastic
washer is used correctly.
M5 x 20mm
Machine Screw
Mounting Post
M5 x 1/8"
Plastic Washer
Back Speaker
Figure 1
4
2. Oncetheproperconfigurationisdetermined,secure
the post to the speaker.
3. SomespeakersusethesmallerM4x8screw,which
isinsertedintotheoff-centeronthemountingpost,
see Figure 2 below.
4. Check the size of the hole, make sure you have the
5/8"-32 x 5/8" machine screw, the 1/4"-20 x 1/2"
machine screw, the M6 x 20mm, or the M5 x 20mm
fits inside, see Figure 3 below.
Figure 3
Figure 2
M4 x 8mm Flat Head
Machine Screw
Back Speaker
M5 x 1/8" Plastic Washer
1/4"-20 x 1/2" Machine Screw
5/8"-32x5/8" Machine Screw
Back Speaker
5
5. When the correct size is determined, place the
screw through the speaker post and attach to the
rear of the speaker enclosure. If the screw does not
tighten properly, use the M5 x 1/8" plastic washer
to tighten it up.
KeyHoleMounting
1. If your speaker has a factory key hole design, you
will use the 5/8"-32 x 5/8" machine screws in
combination with the key hole nut.
2. Loosely pre-assemble the mounting post with the
5/8"-32x5/8"machinescrewandkeyholenut,see
Figure4below. Besurethekeyholenutisinstalled
with the knurled (rough) edge toward the host.
M5 x 1/8"
Plastic Washer
5/8"-32x5/8"
Machine Screw
5/8"-32x5/8"
Machine Screw
Mounting Post
Keyhole
Back Speaker
Figure 4
6
3. Engage the key hole nut into the key hole slot.
4. Puttensionontheassemblybygentlypullingback
on the speaker mount post while tightening the
5/8"-32x5/8"machinescrew,seeFigure4onpage
5.
5. The key hole nut will engage on the housing in the
key hole slot.
6. If the post does not tighten securely against the
housing, it will be necessarry to use the M5 x 1/8"
plastic washer as a spacer under the head of the
5/8"-32x5/8"machinescrew,seeFigure4onpage
5.
2/4 Hole Mounting
1. Findthebestmountingconfigurationthatmatches
yourspeakerenclosure. Four-holemountpatterns
can be accomodated by positioning the speaker
plate diagonally, see Figure 5 on the next page.
2. Usingthe1/4"-20x1/2"machinescrews,installthe
speakerplateandsecurethespeakerenclosure, see
Figure 5 on the next page.
7
1/4"-20 x 1/2"
Machine Screw
4-Hole
Orientation
2-Hole Orientation
Figure 5
Back
Speaker
Self-TappedMounting
1. Locate the optimum location for the mounting
plate and use it as template to mark the drilling
locations. Do not drill or screw into the speaker
where you could possibly damage the internal
components.
2. Drill the pilot hole(s) using a 1/8" drill bit. The
holes(s)shouldnotbedrilledmorethan1/2"depth,
see Figure 6 on the next page.
8
Back Speaker ST5.5 x 19 Self
Tapping Screw
Figure 6
Mounting to the Wall or Ceiling
The mounting hardware for the three different surface
applicationsissupplied. Youwillneedto determinewhat
stylehardwarewillworkbestwithyourmountingsurface.
Always use caution when drilling into a wall or ceiling.
Make sure to avoid all electrical and water lines.
WoodSurface
1. Usingastudfinder,locatethewoodstudorframing
member. Always mount the speakers in the center
of a stud.
2. Using the wall plate as a template, mark hole
positions on mounting surface. For in-wall
applications,positionthemountingholesinavertical
pattern, see Figure 7 on the next page.
9
ST5.5 c 45 Self
Tapping Screw
Figure 7
3. Drill holes through the drywall and into the wood
stud using a 1/8" drill bit. These holes should be
drilled 1-7/8" deep, see Figure 7 above.
4. After the holes are drilled, mount the wall plate
using the self tapping screws.
DrywallSurfaces
1. Locate the best mounting location in the ceiling or
wall. Using the wall plate as a template, mark the
holepositionsonthemountingsurface. Forin-wall
applications,positionthemountingholesinavertical
pattern, see Figure 8 on the next page.
2. Drill holes in the drywall using a 5/16" drill bit.
3. Oncetheholesaredrilled,insertthealligatoranchor
into the holes. Make sure the anchor is flush with
the wall and/or ceiling surface, see Figure8on the
next page.
10
4. With the anchors in place, mount the wall plates
using the ST5.5 x 45 self tapping screws, see
Figure 8 below.
Figure 8
ST5.5 x 45 Self
Tapping Screw
Insert screw through wall plate
and into the alligator anchor
InsertAlligator
Anchor
Pre Drill 5/16"
Holes
ConcreteSurface
1. Using the wall plate as a template, mark hole
positions on the mounting surface. For in-wall
applications,positionthemountingholesinavertical
pattern, see Figure 9 on the next page.
2. Drill holes in the solid concrete or hollow block
using a 5/16" masonry bit. Once the holes are
drilled, insert the # 12-14 alligator anchors into the
holes and make sure the anchor is flush with the
surface of the wall, see Figure 9 on the next page.
Altri manuali per Satellite Speaker Mounts
1
Indice
Altri manuali SIIG Altoparlanti
