SilverStar ES-300 Manuale utente
Industrial Electric Steam Iron
Gravity lron
USER MANUAL
1. Hang Water Tank① at more than
5ft above from the ironing surface
(see figure at the right side) ☞
2. Connect one end of Silicon Hose②
to Solenoid Valve③, and the other
end to Water Tank Valve
④ tap (see figure at the right side) ☞
3. Fix Power Cord⑤ and Silicon Hose②
using S Hook⑥
(see figure at the right side) ☞
4. Connect power plug to power socket,
and turn on Power Switch⑦.
5. Set Temperature Control Knob⑧ to
4 and wait 5 minutes until iron is
heated to the set temperature.
6. Turn Water Tank Valve④ to counter-
clockwise to open and press Steam
Switch⑨ to spray steam.
7. Always place the iron on the Silicon
Plate⑩ when you need to leave the
iron for a while during ironing.
Otherwise, there is a risk of fire.
8. Be sure to turn off power when you
do not use iron, and cool down the
iron at least 30 minutes.
T.F T.S
S S/W R
V H
SOL.V
E.G L
P S/W
2
Iron Installation & Operation
Circuit Diagrams
V : Voltage
P S/W : Power Switch
S S/W : Steam Switch
E.G : Earth Ground
SOL.V : Solenoid Valve
T.F : Over-Temperature
Fuse
T.S : Temperature Setting
R : Resistance
L : Lamp
H : Heater
①Hang Water Tank
②Silicon
Hose
⑤Fix Power Cord
⑦Power
Switch
④Water Tank
Valve
⑥S Hook
1.5M
⑧Control
Knob
⑨Steam Switch
③Solenoid Valve
⑩Silicon
Plate
Do not place iron upright direction when not in use. (See following figure)
1. After iron temperature is sufficiently heated, open water tank valve, and
press the steam switch. (Press for 1~2 seconds and pause for 3~4 seconds.
Repeat, pressing 1~2 seconds then resting 3~4 seconds.)
Press the steam switch this way when you need steam.
2. Start ironing.
3. Do not press steam switch continuously longer than 5~6 seconds for a proper steam function.
4. Select the number of temperature control knob according to corresponding
temperature/ clothes which is following:
# 1, 2 --------- Pre-heating
# 3 ----------- Silk or sensitive clothes (low temperature)
# 4 ----------- Cottons and wool (medium temperature)
# 5 ----------- Other thick clothes (high temperature)
5. Cover ¡°Iron Shoe¡± to iron to get a better ironing effect without glossy to the clothes after ironing.
6. Please keep flammable materials away from the iron during ironing because temperature
of iron plate is very hot (over 200℃). Also, place the iron over silicon plate when not in
use.
7. Always remove the power plug from socket when not in use.
of iron plate is very hot (over 200℃). Also, place iron over silicon plate when not in use.
8. Always remove power plug from socket when iron is not in use.
Problems Check Points Corrective Actions
Iron does not work at all
♧ Is power plug is connected to power socket? ♣ Connect power plug
♧ Is main switch turned on? ♣ Turn on main switch
Steam does not come out
♧ Is there water in water tank? ♣ Fill water to the water tank
♧ Is water tank valve opened? ♣ Turn water tank valve
counter clockwise
♧ Is silicon hose twisted or clogged? ♣ Release twist or remove
clogged materials
Steam pressure is weak ♧ Is water tank valve fully opened? ♣ Fully open water tank valve
♧ Is steam hole clogged? ♣ Unclog steam hole
Water flows out
♧ Does temperature control knob ♣ Adjust tempera control
indicate too low temperature? knob to higher temperature
♧ Is steam switch pressed too long ♣ Press steam switch only
(more than 10 seconds) 1~2 second
Steam comes out when
switch is not pressed
♧ Is steam switch out of order? ♣ Contact head office or A/S
centers
♧ Is rubber packing inside solenoid
valve wore out?
3
Self-Check Points
How to operate
Important Notice
Gravity lron
Please observe following safety regulations to prevent any danger or accidents.
1. Be careful when connecting iron power cord, and check whether iron’s indicated voltage
matches with power supply socket voltage.
2. Fill water tank with clean water. Use of Silver Star's water purifier agent is recommended.
3. Be sure to disconnect the power plug from socket before filling water to water tank.
4. Be careful with steam leakage when connecting silicon hose to water tank and iron.
5. Do not connect multiple plugs to one power socket. There is risk of fire
(Fire Department recommended item).
6. Do not press steam switch continuously (more than 10 seconds). It is the cause of
flowing water instead of steam.
7. Do not press steam switch too hard. It causes the malfunction.
8. User shall always be near to the iron when in use. Iron’s power must be turned off and
its plug must be removed from socket when user needs to leave iron for a while.
9. Do not spray iron steam directly either to human body or animals. There is risk of burn injury.
10. Keep away any part of human body from iron’s bottom plate while in use.There is a risk of burn injury.
11. If the temperature control does not work and keep high temperature, stop
using it immediately and disconnect the plug, then contact authorized service center.
12. If water or other foreign materials entered into iron cover, turn off power by
disconnecting the plug and inquire authorized service center.
13. Remove iron’s power plug from socket when it’s lightning or thunders.
14. Do not let children touch or operate iron.
15. Be sure to change power cable by qualified technician from manufacturer or
authorized
service center when it is damaged.
16. Never touch or modify inner parts of controller in the iron because they are sensitive
parts. There is a risk of iron malfunction or fire if incorrectly handled.
17. Do not touch power cable or operate iron with wet hand. There is risk of electric shock.
18. To clean iron, disconnect power plug from socket and clean it after iron is cooled
down.
19. Remove all steam inside iron and disconnect power plug from socket when iron is not using.
20. Hold power plug when disconnect it from socket. Do not pull out the power cable to
disconnect plug. It is the cause of fire or electric shock by short circuit.
21. Stop using iron, disconnect power plug and contact authorized service center when
there is any other sign or symptoms of trouble.
22. Our company does not have liability for any accident that occurred by not observing
above safety regulations or any accident caused by mistakes or carelessness by user.
Also, our company does not have liability for any accident during or after repair
of the iron by unauthorized person or at unauthorized place.
23. Please contact our head office or authorized service center if you have any question
for
product description or trouble.
Always be sure to observe above safety regulations. Manufacturer does not
have liability for any damages caused by not observing above safety regulation.
4
Safety Regulations
Gravity lron
NO. PARTS NAME NO. PARTS NAME
A BASE SET [ES-300 ] G POWER CORD SET
BASE SET [ES-300L] H WATER BOTTLE SET
B THERMOSTAT SET H-1 WATER BOTTLE
B-1 THERMOSTAT H-2 WATER BOTTLE FILTER
B-2 THERMOSTAT KNOB H-3 WATER BOTTLE VALVE
C SOL VALVE SET [ES-300 ] I SILICONE HOST SET
SOL VALVE SET [ES-300L] J-1 SILICONE IRON REST
D HANDLE CAP SET J-2 COVER [ES-300]
E HANDLE SET COVER [ES-300L]
F MAIN SWITCH SET J-3 THERMO SHIELD
5
ES-300/ES-300L
Gravity lron
NO. PARTS NAME NO. PARTS NAME
A BASE SET [ES-94A ] G POWER CORD SET
BASE SET [ES-94AL] H WATER BOTTLE SET
B THERMOSTAT SET H-1 WATER BOTTLE
B-1 THERMOSTAT H-2 WATER BOTTLE FILTER
B-2 THERMOSTAT KNOB H-3 WATER BOTTLE VALVE
C SOL VALVE SET [ES-94A ] I SILICONE HOST SET
SOL VALVE SET [ES-94AL ] J-1 SILICONE IRON REST
D HANDLE CAP SET J-2 COVER [ES-94A ]
E HANDLE SET COVER [ES-94AL]
F MAIN SWITCH SET J-3 THERMO SHIELD
6
ES-94A/ES-94A Ⅱ/ ES-94AL
Gravity lron
NO. PARTS NAME NO. PARTS NAME
A BASE SET [EZ5 ] G POWER CORD SET
BASE SET [EZ5L ] H WATER BOTTLE SET
B THERMOSTAT SET H-1 WATER BOTTLE
B-1 THERMOSTAT H-2 WATER BOTTLE FILTER
B-2 THERMOSTAT KNOB H-3 WATER BOTTLE VALVE
C SOL VALVE SET [EZ5 ] I SILICONE HOST SET
SOL VALVE SET [EZ5L ] J-1 SILICONE IRON REST
D HANDLE CAP SET J-2 COVER [EZ5]
E HANDLE SET COVER [EZ5L]
F MAIN SWITCH SET J-3 THERMO SHIELD
7
EZ5/EZ5L
Gravity lron
NO. PARTS NAME NO. PARTS NAME
A BASE SET H-1 WATER BOTTLE
B THERMOSTAT SET H-2 WATER BOTTLE FILTER
B-1 THERMOSTAT H-3 WATER BOTTLE VALVE
B-2 THERMOSTAT KNOB I SILICONE HOST SET
C SOL VALVE SET J-1 SILICONE IRON REST
D HANDLE CAP SET J-2 COVER
E HANDLE SET J-3 THERMO SHIELD
F HANDLE BODY SET J-4 MAIN COVER
G POWER CORD SET J-5 I/O SWITCH
H WATER BOTTLE SET
8
ES-90A
Gravity lron
NO. PARTS NAME NO. PARTS NAME
A BASE SET G POWER CORD SET
B THERMOSTAT SET H WATER BOTTLE SET
B-1 THERMOSTAT H-1 WATER BOTTLE
B-2 THERMOSTAT KNOB H-2 WATER BOTTLE FILTER
C SOL VALVE SET H-3 WATER BOTTLE VALVE
D HANDLE CAP SET I SILICONE HOST SET
E HANDLE SET J-1 SILICONE IRON REST
F MAIN SWITCH SET J-2 COVER
9
ES-85AF
Gravity lron
NO. PARTS NAME NO. PARTS NAME
A BASE SET H WATER BOTTLE SET
B THERMOSTAT SET H-1 WATER BOTTLE
B-1 THERMOSTAT H-2 WATER BOTTLE FILTER
B-2 THERMOSTAT KNOB H-3 WATER BOTTLE VALVE
C SOL VALVE SET I SILICONE HOST SET
D HANDLE CAP SET J-1 SILICONE IRON REST
E HANDLE SET J-2 COVER
F MAIN SWITCH SET J-3 THERMO SHIELD
G POWER CORD SET
10
ES-97A
Gravity lron
Questo manuale è adatto per i seguenti modelli
11
Indice
Altri manuali SilverStar Ferro
