SINJI Smart Health Manuale utente
Manual
HEALTH
BRACELET
INDEX
English
Nederlands
Français
Deutsch
Español
Italiano
Português
4
12
21
30
39
48
56
4
1. CONTENTS OF THE PACKAGE
• Sinji Smart Health Bracelet
• Manual
2. TECHNICAL SPECIFICATIONS
• Model: Sinji Smart Health Bracelet
• Band length: 240mm
• Weight: 20g
• Clasp material: Aluminium Alloy
• Strap material: TPU/Silicone
• Waterproof grade: IP67
• Display: 0.87 inch OLED
• Bluetooth: Ver. 4.0
• Battery: Lythium Polymer
Disclaimer:
This Sinji Smart heart rate band is not a medical
instrument. Please consult your general practitioner,
trainer or a specialist to monitor any abnormal results.
EN
5
3. INSTRUCTIONS FOR USE
3.1 How to wear the watch
The Sinji Smart Health bracelet is best worn right
behind the wrist, in such a way that it cannot move
around too much.The sensors on the back of
the band should be in direct contact with skin for
measurements to be possible.
3.2 Charging the Sinji Smart Health bracelet
Please make sure the band is fully charged before
connecting. This ensures the connection to be made
as smoothly as possible.
To charge the band, disconnect the center unit forthe
band as such:
Connect the center unit to any USB-port to start
charging. Charging should be completed after 2~3
hours.
3.3 Downloading the APP
Please search for “Flagfit” in the Android or iOS store,
and download the app.
After downloading, please install the app. When
EN
6
prompted, please allowthe app access to your
phonebook, pictures, and music.
3.4 Operating the Sinji Smart Health bracelet
Turn on the Sinji Smart heart rate band by pressing the
main keyfor 5 seconds, the screen will light up when
ready. The length of press required to turn on the band
can be changed in the Flagfit application.
Turn the band back off by pressing the main key for 5
seconds, selecting “off”, and pressing the main key for
5 seconds once again.
3.5 Pairing the Sinji Smart heart rate band to your phone
• Make sure the band is fully charged before first use
• Make sure bluetooth is enabled on your mobile device
• Press the main key of the watch for a few seconds to
turn the band on.
• Go to the Flagfit app
• Pull down on the white portion of the screen.Your
mobile device will start searching for any nearby
Smart bands
Please note: The band can only be connected to one
device at a time. Before pairing to your phone, make
sure it is disconnected from all other devices.
EN
7
Once the bluetooth connection has been established,
the smart band will automatically connect when
turned on, and in range of your mobile device.
4. MAIN FUNCTIONS
4.1 Personal information and exercise goal
Setting your personal information and exercise
goal when entering the Flagfit app for the first time
ensures measurements are as personalized as
possible. You can edit your personal information and
exercise goals at any time by going into
Settings->Personal settings
4.2 Notifications
You can receive notifications on your smart band if:
1. Notifications are enabled in your mobile device’s
settings.
2. The band and your mobile device remain in close
proximity of each other
The band will vibrate when you receive a new
notification on your mobile device.
• Incoming calls: The band will vibrate and display
caller ID
EN
8
• Message: The band will vibrate and display
contact name
• Alarm Clock: Up to 3 alarms can be set, band will
vibrate
• Sedentary: The band will vibrate if no motion is
detected for set period
4.3 Miscellaneous settings
• Other notifications: Allow for different apps to
send notifications to the Sinji Smart heart rate
band.
• Loss prevention: If turned on, your mobile device
will display an alert ifyour Sinji Smart Health
bracelet is moving away from your mobile device.
• Find Band: If selected in the Flagfit app, the band
will start vibrating to allow for easy retrieval.
• Shake and photograph: When activate it will
allow the Sinji Smart Health Bracelet to take
a picture when the camera app is opened for
easy selfies.
• Firmware upgrade: Searches for newer versions
of the firmware for the Sinji Smart Health
bracelet.
• Factory date reset: resets the band to factory
values. Erases all personal data from the band,
and from the app.
EN
9
4.4 Display options
By pressing the main button on the Sinji Smart Health
bracelet, you can scroll through the different display
options.
1. Clock interface: the main interface of the band.
Shows a Bluetooth icon with a cross if the band is
not connected to your mobile device, and a
bluetooth icon with two waves if a connection is
made.
2. Steps: Shows steps taken since last reset.
3. Distance: Shows distance walked based on steps
and height.
4. Heart Rate: Shows approximate current
heart-rate. You can start testing heart rate by
long pressing the main key in this display mode.
5. SAFETY INSTRUCTIONS
• Keep the product awayfrom sharp objects.
• Don’t place heavy objects on top of the product.
• Don’t use any (chemical or organic) liquids with
the product.
• Keep the product awayfrom heat sources.
EN
10
6. CLEANING
Clean the product with a dry cloth. Don’t use any
chemical liquids or oil!
7. NOTES
1. Please tryto keep the app connected to your
bracelet.
2. Please allow for several seconds of delay for data
transfer between phone and watch.
3. If you need to replace the watch with the same
model, the app will ask you to keep the previous
data: click “sync” to keep the data, click “no” to
remove all previous data.
Please choose carefully!
4. For the first time use, the bracelet needs
personal data for modeling and may appear
inaccurate until the watch has been in
continuous use for 24 Hours, after which the
data will be more and more accurate.
EN
Indice
Lingue:
