Siruba 700K Manuale utente

700K(BKF)

電控參數說明書

ELECTRONIC CONTROL PARAMETER MANUAL

1. 安裝衣襬尺寸導引器 / Welt Guide

Installation……………………………………………………..

2. 檢查及校正位置檢測器 / Checking and Positioning the Position Detector…………………………..

3. 校位及調整衣襬尺寸導引器 / Positioning andAdjusting the Welt Guide………………………………...

A. 盲縫平縫區 Blind Stitch Hemming the Flat Seam Section………………………………………………..

B. 盲縫段縫部

Blind Stitch H

emming the Cross Seam Section…………………………………………….

4. 檢查及調整摺疊器 / Checking andAdjusting the Folder……………………………………………..…

5. 控制箱說明 / Description of the Control Box………………………………………………………………

A. 前視圖 / Front View……………………………………………………………………………………

B. 後視圖 / Rear View…………………………………………………………………………………….

6. 跨越縫檢測器調整 / Adjusting the Cross Seam Detector ………………………………………………….

7.GUDE針數設定 / Setting GUDE Stitch Numbers……………………………………………………………..

A. 吸風功能 / Suction Function…………………………………………………………………………..

B. 斬刀功能 / Type Cutter Function………………………………………………………………………

C. 自動拷下擺功能 / Retractable Guide………………………………………………………………

頁次

1. 安裝衣襬尺寸導引器 / Welt Guide

Installation

A.左右調整將左邊的可撇式導板和落針處中心線對齊。

Making a left or right adjustment, to align the left side of the retractable guide with the center line of the needle.

B.前後調整可將可撇式導板尾端對齊切刀。

Making a forward or backward adjustment, to align the end of the retractable guide with the

cutter.

C.調整可撤式導板座高度 / Adjusting the height of retractable guide base

⑴如圖所示，放鬆螺絲以調整可撤式導板座。

Loosenthe screwto adjust the retractable guidebase as shownin the

figure.

⑵可撤式導板座應和針板平行並間隔

0.03mm

。

The

retractable

guidebase should

parallel to

the needleplate witha 0.03mm

clearance.



針中心

Center of the needle

可撒式導板

Retractable guide

對齊

Line to align with

前後調整螺絲

Front-to-back

ustment screw.

高度調整螺絲

Height adjustment screw

2. 檢查及校正位置檢測器 /Checking and Positioning the Position Detector

A.電源開啟 Turn power ON.

B.檢查指示燈是否有亮 Check whether the indicator lamp is on.

指示燈

Indicator lamp

C. 輕壓檢測器確認位置，檢測器是否亮燈。

Press the detector lightly in to confirm that the cross seam section detector lamp turns on.

⑴未碰觸時，指示燈① OFF，指示燈② ~ ⑥ON。

Without touching, NO.1 detector lamp is OFF, NO.2~NO.6 detector lamps are ON.

⑵輕壓到底，指示燈① ON，指示燈② ~ ⑥OFF。

Press the detector lightly, NO.1 detector lamp is ON, NO.2~NO.6 detector lamps are OFF.

⑶如動作異常，請參考 E「調整感測器位置」，進行感測器位置調整。

If malfunction occurs, please refer to E "Adjusting the Sensor Position " to adjust the position of sensor.

D.調整調節旋鈕，設定所需靈敏度。

Adjust the adjustment knob, set up the required sensibility.

輕押確認

Press lightly to confirm

①②③④⑤⑥

① ② ③ ④ ⑤ ⑥

- +

E. 調整感測器位置 / Adjusting the Sensor Position

⑴鬆開固鎖螺絲。

Loosen the locking screw.

⑵使用三用電表，量測感測器輸出電壓(DC)。

Use multimeter meter to measure the output DC voltage of sensor.

⑶旋轉調節螺絲，調整感測器位置，使感測器輸出電壓介於 DC0.5~0.6V，此時鎖緊固鎖螺絲固定感測器位置。

As shown in the following figure, rotate the adjustment screw to adjust the position of sensor, make the output DC

voltage of sensor lie within 0.5 ~ 0.6V, and then tighten the locking screw to secure the position of sensor.

註：鎖緊固鎖螺絲後，務必確認感測器輸出電壓仍然介於 DC0.5~0.6V 之間

As shown in the following figure, rotate the adjustment screw to adjust the position of sensor, make the output DC

voltage of sensor lie within 0.5 ~ 0.6V, and then tighten the locking screw to secure the position of sensor.

鬆開固鎖螺絲

Loosen the locking screw

調整調節螺絲

Adjust the adjustment screw

紅色探棒黑色探棒

Red probe Black probe

3. 校位及調整衣襬尺寸導引器 / Positioning and Adjusting the Welt Guide

為了防止漏縫，當檢測器檢測到段縫時，可撤式導板會內移，將布料也往內移，如圖所示。接著，

操作盲縫以好的線跡蓋過段縫。蓋過段縫後，可撤式導板會外移回歸原位，恢復正常盲縫操作，

如圖所示。

In order to prevent skip stitching, when a cross seam is detected by the sensor, the retractable guide

starts moving inside and moving the fabric inward, as shown in the following figure. Then, the cross

seam section is sewn over with fine stitches in blind stitch hemming operation. After the cross seam

section sewn, the retractable guide returns to the normal position and the normal blind stitch operation is

resumed, as shown in the following illustration.

→

A.盲縫平縫區 Blind Stitch Hemming the Flat Seam Section.

平縫區

Flat seam section 若縫寬度過大時，順時針旋

轉調節螺絲

If the seam width is too

wide, turn the adjusting

screw clockwise.

若縫寬度過小時，反時針旋轉調

節螺絲

If the seam width is too narrow

turn the adjustment screw

counter clockwise.

調整調節螺絲

Adjust the

adjustment screw

轉鬆螺絲

Loosen the screw

可撒式導板座水平移動

The retractable guide base moves

horizontally

B. 盲縫段縫部

Blind Stitch Hemming the Cross Seam Section.

段縫部

Cross seam section

若段縫處前後縫寬過大，順

時針旋轉螺帽

If the seam widthis too

wide before and after the

cross seam section, turn the

nut clockwise.

如在段縫處前後布料漏縫,

逆時針轉螺帽

If the stitches are missing

before and after the cross

seam section, turn the nut

counter clockwise.

調整調節螺絲

Adjust the adjustment screw

轉鬆螺帽

Loosen the locking nut

織物厚度 The thickness of the fabric to be sewn.

4. 檢查及調整摺疊器 / Checking and Adjusting the Folder

將摺疊器前緣和檢測器的間隔調整成縫紉布料的厚度。

Adjust the gap between the leading edge of the folder and the detector into the thickness of the

fabric to be sewn.

Altri manuali per 700K

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Siruba Macchina da cucire

Siruba

Siruba DL7200D-NM1 Manuale utente

Siruba

Siruba DT828L Manuale utente

Siruba

Siruba LZ457A Scheda tecnica

Siruba

Siruba LKS-1900AN Manuale utente

Siruba

Siruba 700KS-LFD6-K1 Manuale utente

Siruba

Siruba D007R Manuale utente

Siruba

Siruba BH9820 Manuale utente

Siruba

Siruba Sew Reach F007KD Manuale utente

Siruba

Siruba F007D Manuale utente

Siruba

Siruba C007L Manuale utente

Siruba

Siruba HSO-747D Manuale utente

Siruba

Siruba Sew Reach D007S Manuale utente

Siruba

Siruba ASL-JBH200C Manuale utente

Siruba

Siruba DL7200 Manuale utente

Siruba

Siruba ASP-JBL100 Manuale utente

Siruba

Siruba Siruba HSO-747 Manuale utente

Siruba

Siruba 700F Manuale utente

Siruba

Siruba C007K Manuale utente

Siruba

Siruba 700KS Manuale utente

Siruba

Siruba L818F Manuale utente

Siruba

Siruba P717K Manuale utente

Siruba

Siruba DL7200B Manuale utente

Siruba

Siruba NC008 Manuale utente

Siruba

Siruba 700KT Manuale utente

Manuali Macchina da cucire popolari di altre marche

Riccar

Riccar RL634DE Manuale utente

Singer

Singer 2517 Manuale utente

Pfaff

Pfaff 3307-1 SERIES Manuale utente

Janome

Janome Quilt Maker Pro 18 VERSA Manuale utente

Husqvarna Viking

Husqvarna Viking Designer SE Manuale utente

Singer

Singer 148-5 Manuale utente

IKEA

IKEA SY Manuale utente

Pfaff

Pfaff 571 Manuale utente

Singer

Singer 15-91 Manuale utente

Brother

Brother BB370 Manuale utente

Pegasus

Pegasus WT100 Series Manuale utente

Reliable

Reliable 7100DB Manuale utente

Pfaff

Pfaff 937 Manuale utente

Singer

Singer 6038 Manuale utente

Singer

Singer 413K Manuale utente

Pfaff

Pfaff 1471 E1 Manuale utente

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuale utente

HIGHLEAD

HIGHLEAD GC2008-M Manuale utente