Space ULTRA plus Manuale utente
HELPLINE 0861 40 41 42 • WWW.SPACETV.CO.ZA
WITH INTEGRATED FIBRE OPTIC POWER METER
HANDHELD COMBO METER
ULTRA+ Combo Meter - User Manual
HELPLINE 0861 40 41 42 • www.spacetv.co.za
2
1. MAIN FEATURES 3
2. BUTTONS AND INDICATORS 5
3. HOW TO MEASURE 6
4. HOME MENU 7
5. DVB-S/S2 7
5.1 SATELLITE FINDER 7
5.1.1 ZOOM 8
5.1.3 TP CONTROL 8
5.1.4 AUTO DISEQC 9
5.2 LNB SETTING 9
5.3 EDIT SATELLITE 11
5.4 SPECTRUM CHART 11
5.5 ANGLE CALCULATION 12
5.6 DISEQC MONITOR 14
6. DVBT/T2/ISDBT 15
6.1 TERRESTRIAL MEASURE 15
6.2 AUTO SCAN 16
6.3 RF CHANNEL LIST 16
6.4 SCOPE 16
6.5 SPECTRUM CHART 16
6.6 ANT POWER 16
Please refer to the following notes before use.
• Please read this user manual carefully to be able to
safely use and maintain your meter.
• The technical specications and operation guides
in this manual are subject to changes
without notice.
• Before using the rst time, please charge the
battery for 3 hours.
• Please use the special adapter for charging
with the meter, do not use it for other
products
• In case of any technical questions, please contact
your local dealer.
7. DVB-C 17
7.1 CABLE MEASURE 17
7.2 AUTO SCAN 17
7.3 RF CHANNEL LIST 18
7.4 TILT 18
7.5 SPECTRUM CHART 18
7.6 TRUNK VOLTAGE 19
8. ANALOGUE TV 19
8.1 MEASURE 19
8.2 TILT 20
8.3 SPECTRUM 20
9. OPTICAL POWER 20
10. SYSTEM SETTING 20
11. ACCESSORIES 21
12. TROUBLE SHOOTING 21
13. TECHNICAL SPECIFICATION 22
CONTENTS:
HELPLINE 0861 40 41 42 • www.spacetv.co.za 3
Thank you for purchasing this product. For optimum performance and safety, please read these
instructions carefully before connecting, operating or adjusting this product. Please keep this
manual for future reference.
1. MAIN FEATURES
• Support DVBS/DVBS2/DVBT/DVBT2/DVBC/
DVBC2/MCNS/ OPTICAL
• LNB short-circuit protection and indicator.
• Extremely fast and accurate with high
sensitivity.
• 320*240 color LCD display with controllable
back light.
• Database editable by user.
• Audible signal lock notication.
• Optical power level measurement.
• All DiSEqC protocol monitor based on 22KHz
tone.
• Firmware can be upgraded by USB port.
• Power-supply100-240V/50/60Hz 12V@1A.
• Ultra-long standby, low power
consumption.
• Fast charging Li-ion battery that can last
around 3 hours of use.
DVB-S/S2
• Real time Spectrum-Analyzer.
• Transponder message detection.
• Angle calculation of azimuth and elevation.
• Azimuth and elevation measurement.
• Augmented readlity satellite alignment.
• Power, CNR, CBER, VBER(DVBS),
LBER(DVBS2) Modulation mode display.
• DiSEqC1.0, DiSEqC1.2, USALS,SCD and SCD2
supported.
• Auto DiSEqC identication for DiSEqC1.0
• Cable identication for Quattro LNB
DVB-T/T2
• Power, VBER(DVBT), LBER(DVBT2) SNR and
CBER display.
• Spectrum analyzer
• SCOPE Display
• Channel Auto Scan
DVB-C/C2/MCNS
• Power, BER, PER(DVBC/MCNS),
LBER(DVBC2), SNR and Symbol Rate display
• Spectrum analyzer
• Channel Auto Scan
• Trunk voltage measurement (AC&DC)
• Tilt Display
Optical Power
• Highly accurate optic power measurement.
• Optic wavelength 860 ~1610nm
HELPLINE 0861 40 41 42 • www.spacetv.co.za
4
2
3
5
7
12
10
11
91
4
6
8
HELPLINE 0861 40 41 42 • www.spacetv.co.za 5
2. BUTTONS AND INDICATORS
LNB Input:
Signal input port for DVB-S. Connects
directly to LNB using coaxial cable.
Antenna Input:
Signal input port for DVB-T and DVB-C and
ISDB(T). Connect directly to Antenna using
coaxial cable.
Charge Light:
Red: the battery is being charged.
Blue: the battery is full.
Warn Light:
Flash if LNB is short connected
Working Light:
Green: the meter is in working status
Function Keys:
F1: Turn on/o the screen display
F2: Enable/disable deep when pressing
keys
F3: Enter to TP control menu in Satellite
Measure menu
F4: Enter to Auto DiSEqC function in
Satellite Measure menu
Note: Press to display help bar on
menus to get more information.
Navigation Keys:
/: Move focus or change value.
/: Move focus or change value
1. Turn the meter on/o, press and hold
for 2 seconds to power on the meter.
2. Press to show help bar on each menu.
Optical port:
Optical input port.
MENU:
Go into main menu or exit from the
current menu
OK:
Conrm
Charging:
Connect with the charger cord for charging
the equipment.
1
2
3
4
5
6
7
8
9
10
11
12
HELPLINE 0861 40 41 42 • www.spacetv.co.za
6
Power on the meter, select the system to measure or select system setting to set parameters for the
meter in the HOME menu.
In all menus, press [/] button to navigate, press [/] button to change the value of
highlighted item, press [OK] button to conrm your selection, edit value or enter a list to select a
desired item, press [MENU] button to enter or exit menu selection.
How to measure satellite signal:
1. Connect the signal cable to F-Type Female jack.
2. Enter Satellite submenu.
3. Enter to Satellite Measure menu, select the
correct satellite and a transponder that you
want to measure.
By reading values on strength, quality, CNR and
power level, you can peak your dish to get the
best quality signal possible. The user can edit
the satellite position and transponder data in
Satellite Edit menu.
How to measure terrestrial signal:
1. Connect the signal cable to IEC-Type
Female jack rst.
2. Make sure to set Antenna Power to ON
in System Setting menu if your antenna
needs power supply.
3. Analyze the signal in the Terrestrial
Measure menu.
4. Analyze the scope in Scope menu and the
spectrum in Spectrum Chart menu.
How to measure digital cable signal:
1. Connect the signal cable to IEC-Type
Female jack rst.
2. Analyze the signal in cable Measure menu.
How to measure analogue TV signal:
1. Connect the signal cable to IEC-Type
Female jack rst.
2. Analyze the signal in Measure menu.
How to measure optical power:
1. Connect the optical cable to the optical
input port.
2. Enter to optical power sub-menu.
3. Press [/] to switch wavelength
between 850, 980, 1300, 1310, 1490, 1550
and 1610. And press [OK] to switch unit
between dBm and mW.
3. HOW TO MEASURE A SIGNAL
HELPLINE 0861 40 41 42 • www.spacetv.co.za 7
The meter will enter this menu rst when powered on.
Press [/] to switch between icons or [OK] to enter
submenus.
The submenu for DVB-S/S2 functions. User can read the demodulated data of the signal, analyze
the spectrum, calculate the angles for a specic satellite, edit the parameters of satellites and
monitor DiSEqC command for other DVB-S/S2 device.
DVB-S/S2: Submenu for DVB-S/S2 system.
DVB-T/T2/ISDBT: Submenu for DVB-T/T2/ISDBT system.
DVB-C/C2/MCNS: Submenu for DVB-C/C2/MCNS system.
Analogue TV: Submenu for analogue TV system.
Optical Power: Submenu for Optical power measure.
System Setting: Submenu for system parameters
setting.
Such as language, auto power
o, etc.
5.1 SATELLITE FINDER
The device will show the strength and quality of the signal. And also CBER,VBER,LBER,CNR,
modulator type, FEC and power level
• 019.2°EAstra19E:
The current satellite. Press [/] to switch
between satellites and press [OK] to enter satellite
list to select a satellite. Press [OK] button to select the
highlighted satellite and press [MENU] to exit from
edit menu. All the other parameters on the display
will be updated according to the selected satellite.
• 12544-H-22000:
The current transponder. Press [/] to switch
between transponders and press [OK] to enter
edit. Press [/] to move cursor and [/] to
change value of each focused item in edit menu.
• 9750-10600:
The LNB type. Press [/] to switch between LNB
types and press [OK] to enter list to select type.
4. HOME MENU
5. DVBS/S2
HELPLINE 0861 40 41 42 • www.spacetv.co.za
8
5.1 SATELLITE FINDER cont.
• 22K: The 22k output status
• 13V: The 13V antenna power
supply status
• 18V: The 18V antenna power
supply status
• LM: The link margin value.
• CNR: The CNR value of signal.
• 00dBuV: The power level of signal.
• CBER: The BER before FEC value of
signal.
• VBER: The BER before viterbi value
of signal.
• Str: The strength of signal.
• Qlt: The quality value of
signal.
The red background will change to green once
the antenna input signal is locked.
5.1.1 ZOOM
Press F1 to enter into the advanced signal analysis
menu as per screenshot on the right.
5.1.2 LNB Measurement
Press F2 to view the current and voltage that the LNB
is using.
5.1.3 TP CONTROL
TP Control is short for transponder control. Press [F3]
in the Satellite Measure menu to enter this sub-menu.
Press [MENU] to exit to TP Control menu.
HELPLINE 0861 40 41 42 • www.spacetv.co.za 9
5.1.4AUTODISEQC
Press F4 to enter into DiSEqC 1.0 detection menu as
below.
5.2 LNB SETTING
All the LNB parameters are set in this menu. Such as LNB type, LNB power, 22k, Diseqc type and
motor type.
• Astra19E: The current satellite. Press [/]
to switch between satellites and press [OK] to
enter satellite list to select satellite. Press [OK]
button to select the satellite and press [MENU]
to exit from edit menu. All the other parameters
on the menu will be updated according to the
selected satellite.
• 9750-10600: The L.O. type. Press [/] to
switch between L.O. types and press [OK] to
enter list to select type.
• Auto: The 22k parameter. Press [/] button
to switch between Auto, O and On.
• Auto: The power parameters of the LNB. Press
[/] button to switch between Auto, O,
13v and 18v.
• DiSEqC1.0:The DiSEqC port setting for DiSEqC
1.0 and 1.1. Press [/] button to switch
between ports or press [OK] button to select port
in the list. SatCR is also selected from this list.
• Fixed: Set the motor type. Press [/] to
switch between Fixed, USALS and DiSEqC 1.2.
HELPLINE 0861 40 41 42 • www.spacetv.co.za
10
5.2.1Diseqc1.2Setting:
Press [OK] to enter Diseqc 1.2 setting menu on
Position Type if the type sets to Diseqc 1.2
• Movesinglestep: Move the motor by step. Press
[/] to move to west or east
• Moveincrimentaly: To move the motor
incrimentaly. Press [/] to move to west or east
• Movetocentre: Press [OK] to move to centre point
• Limiteast: Set the move limit to east
• Limitwest: Set the move limit to west
• Save: Press [OK] to save current position
• Str.: The strength of signal
• Qlt.: The quality of signal
Indice
