Sper scientific 850009 Manuale utente
UVA/B Light Meter
850009
Instruction Manual
2
UVA/B Light Meter - 850009
Copyright ©2014 by Sper Scientic
ALL RIGHTS RESERVED
The contents of this manual may not be reproduced
or transmitted in any form or by any means electronic,
mechanical, or other means that do not yet exist or may
be developed, including photocopying, recording, or
any information storage and retrieval system without the
express permission from Sper Scientic.
3
CONTENTS
INTRODUCTION .............................. 3
FEATURES .................................. 4
MATERIALS SUPPLIED ........................ 4
LCD DISPLAY ................................ 5
BASIC FUNCTIONS ........................... 6
MODE AND UNIT SELECTION ................... 7
MEMORY .................................. 10
UVA/B SENSOR ............................. 12
BATTERY REPLACEMENT .................... 14
MAINTENANCE ............................. 14
SPECIFICATIONS ............................ 15
WARRANTY ................................ 16
INTRODUCTION
The Sper Scientic UVA/B Light Meter (Model 850009)
is a light-weight, portable instrument that measures
damaging UV (ultraviolet) light in both natural and
manmade environments.
The UV Light Meter measures long and medium
wave UV-A/B light for applications such as forensics,
chromatography, electrophoresis and dermatology.
You can use the meter almost anywhere to determine
UV light intensity and avoid the harmful eects of
overexposure.
4
FEATURES
• Tripod Mounting Socket
• High and low measurement range in milliwatts per
square centimeter (mW/cm2) or microwatts per
square centimeter (µW/cm2)
• Backlit LCD
• Magnetic Mount
• Simultaneous Display of Minimum, Maximum,
Average and Recorded Data
• Zero Point Reset
• Hold Function
• 4 Digit Dual Display
• 20 Points Memory
• Automatic Measuring
• Low Battery Indicator
MATERIAL SUPPLIED
• Meter
• UV Probe
• Magnetic Mount
• 9 Volt Battery
• Instruction Manual
• Hard Carrying Case
5
1. Mode
2. Primary Reading
3. Data Log
4. Auto Mode
5. Memory Review
6. Data Hold
7. Record
8. MAX/MIN/AVG
9. Secondary Reading
10. Time Unit
11. Unit of Measure
12. UV Type
13. Low Battery
LCD DISPLAY
6
BASIC FUNCTIONS
Power On/O
1. Press and hold the HOLD button for 2 seconds to
turn the meter on. All symbols on the LCD will appear
for 1 second.
2. Press and hold the HOLD button for 2 seconds to
turn the meter o. All symbols on the LCD will appear
for 1 second. Release HOLD button.
Reading the LCD Display
1. The primary display indicates measurement value
(also referred to as the “average” value).
2. The secondary display indicates the advanced
functions or data recording (minimum or maximum
reading of the current data set) or your one of your
20 recorded data points.
Meter Function Flow Chart
1. Press MODE to choose the main function
(MAX/MIN/AVG, Zero, Unit, Type or Time). MAX/MIN/
AVG Mode is Normal Mode for this meter and has
several sub-functions as indicated in the diagram on
the next page.
7
MODE AND UNIT SELECTION
Mode Selection
1. Press MODE continuously to cycle through MAX/MIN/
AVG, Zero, Unit, Type, and Time Modes, respectively.
Maximum, Minimum and Average/Normal/Current Mode
1. Press MODE continuously to cycle through modes
until you reach MAX/MIN/AVG.
2. The current measured value appears on the
primary display.
8
3. The primary reading always displays value of measuring.
The secondary reading displays the outcomes of the
advanced functions or data recording. There ar four
modes of measuring functions. Press Sbutton to change
the mode of measuring: None - Max - Min - Avg.
4. Maximum, minimum and average values will appear
and freeze on the secondary display and will update
only when a new maximum, minimum, or average value
is reached on the primary display. Then the secondary
display updates automatically. The average value on the
secondary display updates according to the detected
maximum and minimum values of the current reading.
5. The Max-Min-Avg values can only be recalled if you
saved each point to the memory. Press Mto save the
current, max, min, or avg value for each data point and
the meter will move to the next data point. The stored
data can hold either one current, max, min, or avg value
for each data point.
6. Press S to reset.
Data Hold
1. While in Normal Mode, press HOLD to freeze the
secondary display value. “HOLD” will appear on the
bottom left corner of the LCD.
2. Press HOLD to cancel Hold Mode.
9
Zero Adjustment
1. Press MODE continuously to cycle through modes
until you reach Zero Mode.
2. Cover the sensor. If the main display has a reading
other than zero, perform the zero adjustment.
3. Cover the sensor and press S to zero adjust. The
secondary display indicates the adjustment value
for your reference.
4. Press and hold Sfor 1 second to clear the
adjustment value.
Note…
When the adjustment value is over 10 µW, the
measurement value cannot be oset. The main display
will show the above range reading, and the secondary
display will show “-Err.” Repeat the zero adjustment
procedure or contact Sper Scientic.
5. In Zero Mode, press M to clear data points 0 to 20.
Unit Selection
1. Press MODE continuously to cycle through modes
until you reach Unit Mode.
2. Press S to choose the unit of measure: µW/cm2or
mW/cm2.
Type Selection
This function is reserved for use in future models.
10
MEMORY
Manual Recording
In Normal Mode, press Mto store the current value that
appears on the primary display. The ashing DATA
(01 to 20) icon stops ashing for 2 seconds and moves to
the next storage location. (Refer to Maximum, Minimum
and Average/Normal Mode on pages 10-11 for instructions
on saving max, min, and avg values.)
Auto Recording
To utilize auto recording, you must rst set an interval time
for recording measurement values.
Interval Time Setting
1. Press MODE continuously to cycle through modes
until you reach Time Mode.
2. Continuously press Sto select an interval time for
auto recording of 1, 2, 5, 10, 30 seconds or
1, 3, 5, 10 minutes.
To Auto Record:
1. In Normal Mode, press and hold M for 2 seconds.
“AUTO” appears next to “REC” on the LCD. As soon as
the meter reaches 20 data points, the unit will turn o.
Recorded data includes: Irradiation intensity,
Max/Min/Avg and unit of measure
2. Press M to cancel Auto-Record Mode.
Altri manuali per 850009
1
Indice
Altri manuali Sper scientific Strumento di misura
Sper scientific
Sper scientific 850024 Manuale utente
Sper scientific
Sper scientific 840012 Manuale utente
Sper scientific
Sper scientific Large Display Salinity Pen - 850036 Manuale utente
Sper scientific
Sper scientific 840062 Manuale utente
Sper scientific
Sper scientific AquaShock 850046K Manuale utente
Sper scientific
Sper scientific 850069 Manuale utente
Sper scientific
Sper scientific 800021 Manuale utente
Sper scientific
Sper scientific 300033 Manuale utente
Sper scientific
Sper scientific 300107 Manuale utente
Sper scientific
Sper scientific 850006 Manuale di installazione e d'uso
Sper scientific
Sper scientific 800015 Manuale utente
Sper scientific
Sper scientific 850007 Manuale utente
Sper scientific
Sper scientific 850071 Manuale utente
Sper scientific
Sper scientific 840007 Manuale utente
Sper scientific
Sper scientific 860040 Guida
Sper scientific
Sper scientific 800012 Manuale utente
Sper scientific
Sper scientific 860032 Manuale utente
Sper scientific
Sper scientific 850097 Manuale utente
Sper scientific
Sper scientific 300003 Manuale utente
Sper scientific
Sper scientific 900019 Manuale utente
