Stabila TECH 500 DP Manuale utente

How true pro’s measure

TECH 500 DP

User manual

TECH 500 DP

Contents

Section Page

• 1 Intended use 3

• 2 Safety information 3

• 3. Components of the unit 4

• 4. Display elements 5

• 5. Commissioning 6

• 5.1 Inserting batteries/battery replacement 6

• 5.2 Switching the unit on 6

• 6. Functions 7

• 6.1 Visual guidance 7

• 6.2 Acoustic guidance 8

• 6.3 Automatic display inversion 8

• 6.4 Setting the MODE unit of measurement 9

• 6.5 Locking the measurement with HOLD 9

• 6.6 Freely selectable zero position REF 10

• 6.7 Lighting 11

• 6.8 Key lock 11

• 6.9 Automatic switch-o time: Auto OFF 11

• 7. Checking the measuring tool 12

• 7.1 Accuracy check 12

• 7.2 Calibration 13

• 7.3 Adjusting the sensor 14

• 7.4 Error messages 17

• 8. Technical data 18

TECH 500 DP

1. Intended use

Congratulations on the purchase of your STABILA

measuring tool. The STABILA TECH 500 DP is a digital

measuring tool for measuring inclinations.

If you still have questions aer reading through

the operating instructions, you can obtain advice

by telephone:

+49 63 46 3 09 0

Equipment and functions:

• Tough, independent digital protractor for quick and

accurate measurements

• Integrated rare-earth magnet for attachment

• Integrated V-groove for aligning on round surfaces

• Integrated T-groove for attachment

• Batteries for operation

• Carrying case

2. Safety information

• Read the safety instructions and operating instructions

through carefully.

• Keep these operating instructions in a safe place and

include them when passing the measuring tool on to

another person.

• Do not dispose of the unit with domestic waste.

Please observe the relevant national laws.

• Allow only qualified persons to operate the unit.

• Keep the unit out of the reach of children.

• Do not use in explosive or corrosive environments.

• Do not immerse the unit in water.

• If the unit is dropped or subjected to strong vibrations

it may malfunction.

• Check that the unit is functioning correctly and

accurately at regular intervals, particularly if it

has been exposed to heavy vibrations.

• Do not open the unit.

TECH 500 DP

3. Components of the unit

TECH 500 DP

(dust-proof and waterproof in accordance with IP 65)

Battery compartment lid

Display

T-groove profile for securing with M4 groove stones, e.g.

Bosch Rexroth®or square nut in accordance with DIN 557

V-shape for aligning on round surfaces

Rare-earth magnet

Buttons:

On/Off

Units of measurement: °, %, mm/m, in/ft

Calibration and sensor adjustment

HOLD – locking measurements

Reference – freely selectable zero position

Acoustic guidance

Key lock

Display lighting

3.5 mm

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

TECH 500 DP

4. Display elements

Elements for visual guidance

Acoustic guidance: activated

See chapter 5.1

Units of measurement: °, %, mm/m, in/ft

See chapter 7.4

Reference: activated

See chapter 7.4

Key lock: activated

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

22 20

17 18

TECH 500 DP

5.2 Switching the unit on

Unscrew battery compartment lid, insert new batteries into

battery compartment according to symbol.

Suitable rechargeable batteries can also be used.

LCD indicator:

Battery low – insert new batteries

Dispose of used batteries at suitable collection

points – not with household waste. Do not

leave in unit!

If you do not intend to use the unit for an

extended period, remove the batteries.

5.1 Inserting batteries/battery replacement

5. Commissioning

After switching on with the "ON/OFF" button, an automatic

test is carried out. All the display's segments are shown.

After the end of the test, the version number S x.xx of the

software is briefly displayed and the automatic switch-off

time (Auto OFF) is shown.

An acoustic signal indicates that the unit is ready for

operation.

The display shows the angle measured in the set unit of

measurement.

Alkaline

TECH 500 DP

6.1 Visual guidance

In the range of ± 15° to the horizontal (0°) or to the vertical

(90°), arrows show which way to turn the digital protractor

to reach 0° or 90°.

The 2 "centre display" bars indicate the precise position at

which 0° or 90° is reached.

6. Functions

90°

0°

TECH 500 DP

6.2 Acoustic guidance

6.3 Automatic display inversion

The display is inverted for overhead measurements so that

they are always easy to read.

The acoustic guidance is activated/deactivated using the

"Loudspeaker" button. The tone sequence speeds up as

the 0° or 90° position is approached in a range of ± 2°.

A change in the pitch indicates that these positions have

been exceeded.

A continuous tone confirms the precise point at which 0° or

90° is reached.

TECH 500 DP

6.4 Setting the MODE unit of measurement

6.5 Locking the measurement with HOLD

The unit of measurement is set by pressing the "MODE"

button several times.

° Fine: Display in 0.01° steps

° Rough: Display in 0.1° steps

%: Display in 0.1 % steps

mm/m: Display in 1 mm/m steps

in/ft decimal: Display in 0.01 in/ft steps

in/ft fraction: Display in 1/8 in/ft steps

The set unit of measurement is retained after the unit is

switched off.

The current measurement can be locked by pressing the

"HOLD" button. The visual guidance indicator flashes.

The measurement is displayed continuously.

The locked measurement is deleted by pressing the "HOLD"

button again or switching the unit off.

0,1˚

MODE

0,01°

TECH 500 DP

20°

25°

6.6 Freely selectable zero position REF

The "REF" button can be used to select any set angle as

0° reference. The angle details now displayed relate to

this reference angle. The displayed value flashes with

this setting.

The reference angle value is displayed for 2 seconds by

briefly pressing the "REF" button.

The reference angle is deleted by:

• pressing and holding (≥ 3 sec) the "REF" button.

The activated button lock must be released before

deleting the angle.

• Switching off

• The automatic switch-off function

The zero position then refers back to the original setting.

The alignment selected for the digital

protractor must not be changed during the

reference function, as this could lead to a

display error.

= 25°

+ 5°

RESET

REFERENCE

20°

> 3 sec

2 sec

= 20°

20°

Indice

Altri manuali Stabila Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente