StarTech.com USBDUPE17 Manuale utente

Manual Revision: 08/25/2017

For the latest information, technical specications, and support for

this product, please visit www.StarTech.com/USBDUPE17.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

USBDUPE17

1:7 Standalone USB Duplicator

and Eraser

*actual product may vary from photos

Instruction manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction manual

Table of Contents

Product diagram ....................................................................................1

Top view ....................................................................................................................................................... 1

Back view...................................................................................................................................................... 1

Package contents ...................................................................................2

Requirements .........................................................................................2

About the LED indicators......................................................................2

Set up the duplicator and eraser .........................................................3

Changing the device settings ..............................................................3

Change the startup function ................................................................................................................ 3

Turn o the audio feedback feature................................................................................................... 3

Change the LCD display language...................................................................................................... 4

Restore the default factory settings................................................................................................... 4

Copying USB ash drive data ...............................................................4

Change the copy area.............................................................................................................................. 4

Check the ash drive capacity.............................................................................................................. 5

Set the target tolerance.......................................................................................................................... 5

Change the copying speed ................................................................................................................... 6

Change the time between copy and compare............................................................................... 6

Set the device to automatically check the USB ash drive ........................................................ 7

Complete a synchronous copy............................................................................................................. 7

Complete an asynchronous copy........................................................................................................ 8

Interrupt the copying process.............................................................................................................. 8

Disable the asynchronous feature ...................................................................................................... 9

Copy to an HDD or SSD........................................................................................................................... 9

Instruction manual

Compare USB ash drives ...................................................................................................................... 9

Copy and compare USB ash drives................................................................................................... 9

Formatting a USB ash drive................................................................10

Auto format a USB ash drive............................................................................................................... 10

Format a USB ash drive to FAT16....................................................................................................... 10

Format a USB ash drive to FAT32....................................................................................................... 11

Set the FAT16 cluster size ....................................................................................................................... 11

Set the FAT32 cluster size ....................................................................................................................... 12

Erasing USB ash drives........................................................................12

Perform a quick erase .............................................................................................................................. 12

Perform a full erase................................................................................................................................... 13

Perform a DoD erase................................................................................................................................ 13

Update the system rmware ................................................................14

Calculate the checksum number .........................................................14

Measure read and write speeds...........................................................14

Analyzing the quality of a USB ash drive .........................................15

Perform a media check ........................................................................................................................... 15

Change the range limit percentage ................................................................................................... 15

Change the MB range limit.................................................................................................................... 16

Change the error limit............................................................................................................................. 16

View information about a USB ash drive .........................................16

View system information ......................................................................17

Technical support...................................................................................18

Warranty information............................................................................18

Instruction manual

Product diagram

Top view

1LCD display

2UP button

3DOWN button

4OK button

6Source USB ash drive port

7Source USB ash drive LED indicators

8Destination USB ash drive port

9Destination USB ash drive LED indicators

5ESC button

Back view

10 Power switch

11 Power adapter port

Instruction manual

Package contents

• 1 x duplicator and eraser

• 1 x universal power adapter (NA/JP, UK, EU, ANZ)

• 1 x quick-start guide

Requirements

• 1 source USB ash drive

• 1 to 7 destination USB ash drives

To connect an SD, an SDHC, a microSD, a miniSD, an MMC, or a CF card, you require a

USB multimedia card reader for each of the USB ash drive ports.

Requirements are subject to change. For the latest requirements, please visit

www.StarTech.com/USBDUPE17.

About the LED indicators

Each of the eight USB ash drive ports feature a detection/activity LED and an

error LED.

LED behavior Signicance

Green LED is blinking Command is being executed

Warning! Do not remove the USB ash drive

when the green LED is blinking.

Green LED is illuminated USB ash drive is detected

Process is complete

Red LED is illuminated An error occurred

For more information, see the LCD display.

Instruction manual

Changing the device settings

In the Setup menu, you can change the settings of the duplicator and eraser, including

the button sound, display language, and so on.

Change the startup function

You can select the function that is displayed when you turn on the duplicator and

eraser. By default, the copy function is displayed when you turn on the device.

1. Highlight Setup and press the OK button.

2. Highlight Start-up Menu and press the OK button.

3. Highlight the function that you want displayed when you turn on the duplicator

and eraser, and press the OK button.

Turn o the audio feedback feature

By default, the audio feedback feature is enabled.

1. Highlight Setup and press the OK button.

2. Highlight Button Sound and press the OK button.

3. Highlight OFF and press the OK button.

Set up the duplicator and eraser

1. Connect the universal power adapter to the Power adapter port on the duplicator

and eraser and to a power source.

2. Use the Power switch to turn on the duplicator and eraser.

3. Press the UP and DOWN buttons to navigate the menu and highlight selections.

4. Press the OK button to make selections.

5. To exit a menu selection, press the ESC button.

For more information about the features and functions of the duplicator and eraser,

see the applicable sections of the manual.

Instruction manual

Copying USB ash drive data

Each USB ash drive port on the duplicator and eraser has an independent control

processing unit and supports asynchronous and synchronous copying.

Change the copy area

You can set the duplicator and eraser to copy the system and les or all of the data on

the USB ash drives.

System and Files

If you select System and Files as the copy area, the system analyzes the le format of

the source USB ash drive and if the format is recognizable (for example, FAT16,

FAT32, NTFS, Linux ext. 2, and so on), the system will only copy the data and not the

entire USB ash drive. If the system doesn’t recognize the le format, it will copy the

entire storage capacity of the source USB ash drive, including any empty space. This

type of copy is also known as “quick copy.”

Whole Media

If you select Whole Media as the copy area, the system copies the entire source USB

ash drive, including les and empty space. This option is useful if you’re copying the

entire source USB ash drive or if you don’t know the format of the USB ash drive.

Copying the whole media area of a source USB ash drive takes longer to complete

than copying the system and les area.

By default, System and Files is set as the copy area.

Change the LCD display language

1. Highlight Setup and press the OK button.

2. Highlight Language and press the OK button.

3. Highlight English or Japanese and press the OK button.

Restore the default factory settings

1. Highlight Setup and press the OK button.

2. Highlight Set to Default and press the OK button.

3. When the conrmation message appears, press the OK button.

Instruction manual

1. Highlight Setup and press the OK button.

2. Highlight Copy Area and press the OK button.

3. Do one of the following:

• Highlight System and Files and press the OK button.

• Highlight Whole Media and press the OK button.

Check the ash drive capacity

If a USB ash drive passes the capacity check, the green LED indicator next to the USB

ash drive port illuminates. If a USB ash drive fails the capacity check, the red LED

indicator next to the USB ash drive port illuminates.

1. Use the Power switch to turn on the duplicator and eraser.

2. Insert up to eight USB ash drives in any of the USB ash drive ports.

3. Highlight Capacity Check and press the OK button.

4. To view the capacity of the USB ash drives, use the UP and DOWN arrows to

navigate through the list of USB ash drive ports.

Tip! This feature supports asynchronous operation, which means that the system

checks each USB ash drive separately. You can remove a USB ash drive after it has

been checked and insert a dierent USB ash drive and the check will continue.

Set the target tolerance

You can set the capacity tolerance range between the source USB ash drive and

the target USB ash drive, and if the capacity of the USB ash drive is outside of the

tolerance range, the data won’t be copied. For example, if you set the target tolerance

to ±1% and the source USB flash drive is 2GB and the destination USB flash drive is

2.02GB, the data won’t be copied to the destination USB flash drive.

By default, the target tolerance is set to No Limit.

1. Highlight Setup and press the OK button.

2. Highlight Target Tolerance and press the OK button.

3. Do one of the following:

• To disable the capacity tolerance range, highlight No Limit and press the OK

button.

Caution! If the amount of data on the source USB ash drive is larger than the

Instruction manual

data capacity of the destination USB ash drive and there is no limit to the

capacity tolerance range, the copying process will fail or be incomplete.

• To set the data capacity of the destination USB ash drive to be the exact same

as the source USB ash drive, highlight 100% Same and press the OK button.

Caution! If the data capacities of the source USB ash drive and destination

USB ash drive aren’t equal, the copying process won’t begin.

• To set the high and low range of the capacity tolerance range between the

source USB ash drive and the destination USB ash drive, highlight Allow

Tolerance and press the OK button. To set the maximum capacity dierence,

highlight No Limit or a numeric value between 0 and 50%, and press the

OK button. To set the minimum capacity dierence, highlight No Limit or a

numeric value between 0 and 50%, and press the OK button.

Change the copying speed

For most types of USB ash drives, you should set the copy speed to Normal.

1. Highlight Setup and press the OK button.

2. Highlight Working Mode and press the OK button.

3. Highlight one of the following and press the OK button:

• Fastest Mode

• Faster Mode

• Normal Mode

• Slower Mode

• Slowest Mode

Tip! If you’re experiencing a high failure rate when you’re copying USB ash drives, try

using a slower copying speed.

Change the time between copy and compare

By default, the duplicator and eraser is set to wait 3 seconds after a copy process

completes before beginning the compare process.

1. Highlight Setup and press the OK button.

2. Highlight Power O Time Between Copy&Compare and press the OK button.

3. Highlight a numeric value between 0 and 15 and press the OK button.

Indice

Altri manuali StarTech.com Hardware per computer

StarTech.com

StarTech.com MPEX1394B3 Manuale utente

StarTech.com

StarTech.com PEX2MPEX Manuale utente

StarTech.com

StarTech.com S32M2NGFFPEX Manuale utente

StarTech.com

StarTech.com PCISATA2P4 Manuale utente

StarTech.com

StarTech.com PEXUSB400 Manuale utente

StarTech.com

StarTech.com PCI225USB Manuale

StarTech.com

StarTech.com PEX1S552LP Manuale

StarTech.com

StarTech.com S25SLOTR Manuale del sistema

StarTech.com

StarTech.com SATSASBP125 Manuale utente

StarTech.com

StarTech.com SATSASBAY3BK Manuale utente

StarTech.com

StarTech.com CABSHELF22V Manuale utente

StarTech.com

StarTech.com PCISATA4R1 Manuale utente

StarTech.com

StarTech.com PCISOUND5CH Manuale utente

StarTech.com

StarTech.com 16C1050 Manuale utente

StarTech.com

StarTech.com ECUSB3S254F Manuale utente

StarTech.com

StarTech.com 8STPEXM2SAT32N1 Manuale utente

StarTech.com

StarTech.com PEXUSB312A Manuale utente

StarTech.com

StarTech.com CARDBUS CB420USB Manuale utente

StarTech.com

StarTech.com EC230USB Manuale utente

StarTech.com

StarTech.com PEXSAT34RH Manuale utente

StarTech.com

StarTech.com SATSASBAY3BK Manuale utente

StarTech.com

StarTech.com PEX4S552B Manuale utente

StarTech.com

StarTech.com FAN8025PWM Manuale utente

StarTech.com

StarTech.com PEXESAT322I Manuale del sistema

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente