Steiner DBAL-I2 Manuale utente
DUAL BEAM AIMING LASER
VISIBLE LASER POINTER / IR LASER
Technical anual
TABLE OF CONTENTS
Page
SAFETY SU ARY...............................................................................2
HOW TO USE THIS ANUAL ..................................................................7
GENERAL INFOR ATION.......................................................................8
EQUIP ENT DESCRIPTION....................................................................12
SECTION I OPERATING INSTRUCTIONS ..................................................18
SECTION II OUNTING PROCEDURES ....................................................35
SECTION III ZEROING PROCEDURES ......................................................39
SECTION I OPERATOR PREVENTIVE AINTENANCE CHECKS ..................53
SECTION II OPERATOR TROUBLESHOOTING ...........................................59
SECTION III OPERATOR AINTENANCE..................................................62
SECTION I UNIT TROUBLESHOOTING.....................................................66
SECTION II UNIT AINTENANCE ...........................................................69
SECTION III SERVICE/PACKING AND UNPACKING...................................74
REPAIR PARTS .....................................................................................77
SAFETY SUMMARY
WARNING
INVISIBLE LASER RADIATION
AVOID DIRECT EXPOSURE TO THE BEA
GREEN or RED VISIBLE LASER POINTER - Class IIIa
LASER WAVELENGTH: RED - 635 nm / GREEN - 532 nm
OUTPUT: <5 mW
INFRARED LASER POINTER - CLASS I
OUTPUT: IR LASER: <0.7 mW / WAVELENGTH: 850 nm
• DO NOT stare into the laser beam.
• DO NOT look into the laser beam through binoculars or telescopes.
• DO NOT point the laser beam at mirror-like surfaces.
• DO NOT shine the laser beam into other individual’s eyes.
2
Safety Data
LASER Power SAFETY
Output CLASS NOHD (m)
REEN LASER - High Power <5 mW IIIa 56.8
RED LASER - High Power <5 mW IIIa 199.7
DEFINITION OF THE FOLLOWING ALERTS THROUGHOUT THIS ANUAL:
WARNING
Identifies a clear danger to the person doing that procedure.
CAUTION
Identifies risk of damage to the equipment.
NOTE
Used to highlight essential procedures, conditions, statements, or convey
important instructional data to the user.
3
WARNING
Be sure the weapon is CLEAR and on SAFE before proceeding.
WARNING RISK OF DETECTION BY ENEMY
To reduce the risk of detection by an enemy using a Night Vision Device
(NVD), avoid prolonged activation of the DBAL-I2.
The infrared beam is more detectable to an enemy using a NVD when used in
smoke, fog and rain. Avoid prolonged activation of the DBAL-I2in these conditions.
WARNING
DO NOT store the DBAL-I2with the battery installed.
WARNING
The High Power Modes are blocked with a safety screw.
WARNING
To operate the DBAL-I2in the High Power modes the blue safety screw must
be removed from the back of the unit. The Armorer will remove and store the
safety screw.
WARNING
All directions, such as CW and CCW, are given from the shooter’s point of
view, as though the DBAL-I2were weapon-mounted.
WARNING
The DBAL-I2is powered by one 3-volt CR 123A Lithium Manganese Dioxide
(Li/MnO2) battery. The following safety precautions apply when handling
lithium batteries: 4
• DO NOT short circuit, puncture, or disassemble
• DO NOT attempt to recharge
• NEVER dispose of lithium batteries in a fire, or in any way expose lithium
batteries to excessive heat
• Batteries may explode if disassembled, crushed, recharged, or exposed to
high temperatures
• Avoid mechanical or electrical abuse
• Prior to use, inspect all batteries for cracks, leakage, or bulging
• NEVER install a defective battery in the DBAL-I2
• DO NOT install battery incorrectly
• Store at room temperature
• Refer to applicable federal, state, and local laws and regulations for proper
disposal of the batteries
WARNING
Make sure the Activation Mode Selector Switch is in the
OFF position before inspecting the Exit Port Lenses of the DBAL-I2.
WARNING
If the Activation Selector Switch is not in the OFF position, the laser can be
inadvertently activated by depressing the fire button on the top of the housing.
WARNING
If a laser borelight is used to boresight the DBAL-I2, be sure to remove the
borelight from the weapon prior to firing.
5
WARNING
NEVER boresight in the High Power mode of operation.
CAUTION
DO NOT over-adjust the laser adjusters by forcing them beyond their end
of travel.
CAUTION
DO NOT defocus the infrared illuminator by forcing it beyond its normal end
of travel.
CAUTION
DO NOT overtighten the Safety Screw when installing it into the DBAL-I2
housing as you may strip the housing threads.
CAUTION
Prior to submerging the DBAL-I2, make sure the infrared illuminator focusing
knob has been adjusted in a CCW direction to the focus point.
CAUTION
Use ONLY authorized cleaning supplies on the DBAL-I2or permanent damage
may occur.
CAUTION
DO NOT remove the Remote Cable Switch by pulling on the cable.
CAUTION
To prevent damage to the IR ILLUM Exit Port Cover, open the Dust Cover
before turning the knob to adjust the focus. 6
how to use this manua
Usage
You must familiarize yourself with the entire manual before operating
the equipment. Read the complete maintenance task before performing
maintenance and follow all WARNINGS, CAUTIONS and NOTES.
anual Overview
The manual contains sections for Operating and Maintaining the DBAL-I2.
Appendix A Repair Parts
7
CHAPTER 1-–-GENERAL INFORMATION
8
Figure 1-1 DBAL-I2in Use
1.1 GENERAL INFOR ATION
1.1.a Type of anual:
Operator and Field Maintenance Manual.
1.1.b Equipment Name:
DBAL-I2, Dual Beam Aiming Laser-Intelligent2.
1.1.c Purpose of Equipment:
To covertly illuminate and direct fire using an infrared laser pointer (IR
POINT) and an infrared laser illuminator (IR ILLUM) for operators equipped
with a Night Vision Device (NVD).
1.2 REPORTING EQUIP ENT I PROVE ENT RECO ENDATIONS
If your DBAL-I2needs improvement, let us know.
Mail your comments to Steiner-Optik, 331 E. 8th St., reeley, CO 80631
or email: laserlightsinf[email protected]om
1.3 Steiner 3-Year Laser Device Warranty
On all laser devices, Steiner offers a 3-Year Limited Warranty from the date of
purchase that covers all laser, optical and electronic components, materials
and workmanship. All warranties are void if the serial number or manufacturer’s
labels affixed to the product have been removed, or if products have been
abused, misused, modified, neglected or have been disassembled prior to
return to the manufacturer.
9
Indice
Altri manuali Steiner Strumento di misura
