Sun Microsystems SPARC Enterprise T5240 Manuale utente

This guide describes the minimum steps you must perform to get Oracle’s Sun SPARC Enterprise T5240 server to power on

and boot for the first time using the preinstalled Oracle Solaris Operating System (Solaris OS).

FIGURE 1 Sun SPARC Enterprise T5240 Server

Shipping Contents

Quick Setup Instructions

For quick installation and configuration, follow these steps. For more detailed information, refer to the complete online

product documentation set at: http://docs.sun.com/app/docs/prod/sparc.t5240

Understand the following information before you set up the server for the first time:

■Choose the best instructions for your situation – These quick setup instructions work for any networking environment,

and require the use of a terminal device for connectivity to a serial port. If you have a networking environment running

DHCP, you can configure your system using the Ethernet management port. To take advantage of DHCP setup method,

refer to the online installation guide instead of these instructions.

■Set aside sufficient time – Installation times vary, but if you are performing these setup instructions for the first time,

plan to spend about 45 to 75 minutes to complete all of these instructions. Additional time might be required for

installing optional hardware and rackmounting kits.

■Gather your configuration information – During the configuration, you are prompted for time zone and networking

parameters that are specific to your environment. For a list of information you need, see Step 9.

■Obtain a terminal device – You configure this rackmountable server through the service processor (SP) using the built-in

serial and network management ports, and not through a graphical interface and Sun keyboard. For more information

about the terminal device, see Step 3.

■Do not apply power at this time – This system includes a service processor (SP) that is used to configure and boot the

main host server. To properly configure the host server and view SP messages, do not apply AC power to the server until

the SP and host networking connections are made, as described in this guide.

Quantity Item

1 Server

2 RJ-45 Ethernet cable

1 RJ-45 to DB-25 adapter (crossover)

1 RJ-45 to DB-9 adapter (crossover)

2 Power cords (packaged separately)

Sun SPARC Enterprise T5240 Server

Getting Started Guide

1. Unpack the server, and check that you received all of the shipping contents.

2. Place the server in its intended location for verification.

For rackmounting instructions, refer to the instructions included with the rail kit, the service label on the server, and to

the online Sun SPARC Enterprise T5140 and T5240 Servers Installation Guide.

3. Connect a serial cable between the server’s SER MGT port (FIGURE 2) and a terminal device.

This connection provides your initial communication with the service processor (SP).

The terminal device can be a terminal, a terminal server, or a laptop with terminal emulation software running. The

device must be set up to communicate using 9600 baud, 8 bit, no parity, 1 stop bit. A null modem configuration is needed,

meaning the transmit and receive signals are reversed (crossed over) for DTE to DTE communications. You can use the

supplied RJ-45 crossover adapters with a standard RJ-45 cable to achieve the null modem configuration.

FIGURE 2Server Connections

4. (Optional) Connect an Ethernet cable between the server’s Net MGT port (FIGURE 2) and the network to which future

connections to the SP and host will be made.

After the initial configuration of the system using the SP SER MGT port, communication with the SP and host is usually

performed through this Ethernet interface.

5. Connect an Ethernet cable between one of the server’s NET ports (FIGURE 2) and the network to which the server will

communicate.

Numbered cables

correspond to setup steps.

(Optional)

6. Plug the power cords into the power supplies and into a power source.

Note - Only one power connection is required for operation. Use two power connections for redundancy.

When power is applied, the SP initializes and power supply LEDs illuminate. After a few minutes, the SP login prompt

appears on the terminal device. The host is not initialized or powered on yet.

7. At the terminal device, log in to the SP as root with a password of changeme.

After a brief delay, the SP prompt is displayed (->). At this point, there are many commands you can perform using the

Integrated Lights Out Manager interface.

Additional SP information, such as how to change the password and how to set up the SP network parameters is

available in the online documentation set.

8. Power on the server and redirect the host output to display on the serial terminal device:

After you start the SP console, the server initialization takes approximately 20 minutes to complete.

SUNSP00144FAC732F login: root

Password: changeme

. . .

-> start /SYS

Are you sure you want to start /SYS (y/n)? y

-> start /SP/console

Are you sure you want to start /SP/CONSOLE (y/n)? y

Serial console started. To stop, type #.

. . .

9. When prompted, follow the onscreen instructions and enter the following configuration information.

You will be prompted to confirm the configuration several times, enabling confirmation and changes. If you are not sure

how to respond to a particular value, you can accept the default, and make future changes when the Solaris OS is

running.

When the configuration menus are completed, the server reboots and displays the Solaris login prompt.

10. Log in to the server and explore the capabilities.

There are many commands you can use to verify the functionality of the system. The following list describes a few of

them:

■showrev – Displays the hostname and system architecture information. Use the -a option with this command to see

the patches that are installed.

■psrinfo – Displays information about the number and status of the processors and cores in the host.

■prtdiag – Displays system configuration and diagnostic information.

Review the Solaris OS man pages and documentation for more details.

Parameter Description

Language Select a number from the displayed language list.

Locale Select a number from the displayed locale list.

Terminal Type Select a terminal type that corresponds with your terminal device.

Network? Select Yes.

Multiple Network Interfaces Select the network interfaces that you plan to configure. If you are not sure, select the first

one in the list.

DHCP? Select Yes or No according to your network environment.

Host Name Enter the host name for the server.

IP Address Enter the IP address for this Ethernet interface.

Subnet? Select Yes or No according to your network environment.

Subnet Netmask (If subnet was Yes) Enter the netmask for the subnet for your network environment.

IPv6? Specify whether or not to use IPv6. If you are not sure, select No to configure the Ethernet

interface for IPv4.

Security Policy Select either standard UNIX security (No) or Kerberos Security (Yes). If you are not sure,

select No.

Confirm Review the onscreen information and change it if needed. Otherwise, continue.

Name Service Select the name service according to your network environment.

Note–If you select a name service other than None, you will be prompted for additional name

service configuration information.

NFSv4 Domain Name Select the type of domain name configuration according to your environment. If you are not

sure, select Use the NFSv4 domain derived by the system.

Time Zone (Continent) Select your continent.

Time Zone (Country or Region) Select your country or region.

Time Zone Select the time zone.

Date and Time Accept the default date and time or change the values.

root Password Enter the root password twice. This password is for the superuser account for the Solaris OS

on this server. This password is not the SP password.

Accessing Additional Information

You can view, print, and download additional information for this product from the following URLs:

■Oracle’s Sun SPARC Enterprise T5240 server documentation set, including important documents such as product notes:

http://docs.sun.com/app/docs/prod/sparc.t5240

■A broad selection of Sun documentation, including localized versions:

http://www.sun.com/documentation

■Preinstalled Solaris OS information:

http://www.sun.com/software/preinstall

■CoolThreads – Overview access to Cool Tools:

http://www.sun.com/servers/coolthreads/tnb/index.jsp

■CoolThreads – CMT Tuning and Resources:

http://www.sun.com/servers/coolthreads/tnb/t2.jsp

Technical Support

If you have technical questions about this product that are not answered in this document, go to:

http://www.sun.com/service/contacting

Documentation Feedback

Submit comments about this document by clicking the Feedback[+] link at:

http://docs.sun.com/

Please include the title and part number of your document with your feedback:

Sun SPARC Enterprise T5240 Server Getting Started Guide, part number 820-3521-11

Part No. 820-3521-11, Rev. A

July 2010

Bar Code Area

(Delete this text)

Indice

Altri manuali Sun Microsystems Server

Sun Microsystems

Sun Microsystems Blade X6270 M2 Manuale utente

Sun Microsystems

Sun Microsystems Sun Fire E2900 Manuale di istruzioni

Sun Microsystems

Sun Microsystems SunSwift SPARCserver 1000 Manuale utente

Sun Microsystems

Sun Microsystems Sun Fire V60 Series Come usare

Sun Microsystems

Sun Microsystems Sun Fire X4150 Server Manuale utente

Sun Microsystems

Sun Microsystems Sun Fire V490 Manuale

Sun Microsystems

Sun Microsystems Sun Fire V890 Manuale di servizio

Sun Microsystems

Sun Microsystems Netra X1 Manuale di servizio

Sun Microsystems

Sun Microsystems Sun Fire V20z Manuale di programmazione

Sun Microsystems

Sun Microsystems Netra 1290 Manuale utente

Sun Microsystems

Sun Microsystems Fire 3800 Manuale utente

Sun Microsystems

Sun Microsystems Fire V440 2-Post Manuale utente

Sun Microsystems

Sun Microsystems Fire V210 Manuale utente

Sun Microsystems

Sun Microsystems Sun Fire V445 Manuale di istruzioni

Sun Microsystems

Sun Microsystems Sun Fire T1000 Manuale di istruzioni

Sun Microsystems

Sun Microsystems SPARC Enterprise T1000 Manuale di istruzioni

Sun Microsystems

Sun Microsystems Sun Enterprise 6500 Manuale utente

Sun Microsystems

Sun Microsystems Sun Java SystemDirectory Server Manuale utente

Sun Microsystems

Sun Microsystems Netra 120 Manuale utente

Sun Microsystems

Sun Microsystems SUN FIRE X4500 Manuale utente

Sun Microsystems

Sun Microsystems Sun SPARC Enterprise M8000 Manuale di servizio

Sun Microsystems

Sun Microsystems Blade 8000 Series Manuale tecnico

Sun Microsystems

Sun Microsystems SPARC T5120 Manuale utente

Sun Microsystems

Sun Microsystems Sun Enterprise 220R Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente