TechnoAP APV8516-14 Manuale utente

Digitizer

Model: APV8516-14

Instruction Manual

1.0.1 Edition

March 2020

TechnoAP Co., Ltd.

2976-15 Mawatari, Hitachinaka-shi, Ibaraki 312-0012, Japan

TEL. +81-29-350-8011 FAX. +81-29-352-9013

http://www.techno-ap.com

Edition 1.0.1 March / 2020

2/42

TechnoAP Co., Ltd.

Edition 1.0.1 March / 2020

3/42

TechnoAP Co., Ltd.

Safety Precautions / Disclaimer

Thank you very much for purchasing the Digital Pulse Processor, Model: APV8102-14MWPSAGb (hereinafter ”This

board”) Please read this "Safety Precautions / Disclaimer" before using this board, be sure to observe the contents,

and use it correctly.

We are not responsible for any damage caused by abnormality of board, detector, connected devices, applications,

damages to failure, other secondary damages, even if accident caused by using this board.

Prohibited matter

◼This device cannot be used for applications requiring special quality and reliability

related to human life, accident.

◼This device cannot be used in places with high temperature, high humidity and high

vibration.

◼Do not apply strong shock or vibration to this device.

◼Do not disassemble or modify this device.

◼Do not wet this device with water or condensation. Do not operate this device with

wet hands.

◼If there is heat generation, deformation, discoloration, odor, etc. in this device, stop

using it immediately and contact us.

Caution

◼Use this device at room temperature in the operating temperature range and use it

so that there is no condensation.

◼If there is smoking or abnormal heat generation in this device, turn off the power

immediately.

◼Be careful of static electricity because this device is a precision electronic device.

◼Do not store this device in a dusty place or high temperature / high humidity place.

◼Do not place devices that emit strong electromagnetic waves, such as mobile

phones and transceivers, close to this device.

◼This device may malfunction in environments with high electrical noise.

◼The specifications of this device and related documents may be subject to change

without prior notice.

Edition 1.0.1 March / 2020

4/42

TechnoAP Co., Ltd.

Guarantee conditions

The warranty conditions of "our products" are as follows.

Warranty period

One year from date of purchase.

Guarantee contents

Repair or replacement will be carried out in case of breakdown even though you have

used correctly according to this instruction manual within the warranty period

Out of warranty

We do not warranty if the cause of the failure falls under any of the following.

1. Failure or damage due to misuse or improper repair or modification or disassembly.

2. Failure and damage due to falling etc.

3. Breakdown / damage in harsh environments (high temperature / high humidity,

under zero, condensation etc.).

4. Causes other than the above, other than "our products".

5. Consumables.

6. Natural disasters such as fire, earthquake, flood damage, lightning, etc. and

breakdown due to theft.

7. When the cause of the malfunction is found to be wet

* Even during the warranty period, costs may be incurred for repair or replacement. Please read the contents of

"Safety Instruction and disclaimer" carefully and use it correctly.

Edition 1.0.1 March / 2020

5/42

TechnoAP Co., Ltd.

１． Abstracts.............................................................................................................................................6

１．１． Specification........................................................................................................................................ 7

１．２． Operation System Requirements............................................................................................ 7

１．３． Revision History................................................................................................................................ 7

２． External...............................................................................................................................................8

３． Preparation........................................................................................................................................9

３．１． Display.................................................................................................................................................... 9

３．２． Installation of the application...................................................................................................... 9

３．３． Power ON and IP Connection Confirmation...................................................................... 9

３．４． Connection........................................................................................................................................... 11

３．５． Setting of FAST filter....................................................................................................................... 13

３．６． Setting of SLOW filter..................................................................................................................... 14

３．７． Setting of Threshold........................................................................................................................ 14

４． Window................................................................................................................................................16

４．１． Startup window.................................................................................................................................. 16

４．２． Config Tab............................................................................................................................................. 18

４．３． File Tab................................................................................................................................................... 25

４．４． Status Tab............................................................................................................................................. 26

４．５． Wave Tab.............................................................................................................................................. 27

４．６． Spectrum Tab...................................................................................................................................... 29

５． File......................................................................................................................................................... 30

５．１． Histogram Data File........................................................................................................................ 30

５．２． Wave Data File................................................................................................................................... 32

５．３． List Data File....................................................................................................................................... 33

６． Measurement................................................................................................................................... 35

６．１． Measurement of energy spectrum in histo mode ....................................................... 35

６．２． List measurement .................................................................................................................... 39

Contents

Edition 1.0.1 March / 2020

6/42

TechnoAP Co., Ltd.

１． Abstracts

The APV8516-14 is a waveform analysis board for scintillation detectors. Each channel (16 CH.) is equipped with

high-speed, high resolutionADC (500 MHz, 14-bit). The APV8516-14 can correspond to the high rates of more than

200 kcps per CH. in the list mode with using the Gigabit Ethernet (Gb Ether) connection.

Structure

*In this instruction manual, “List” and “Event” are equivalences.

*In this instruction manual, “Histogram” and “Spectrum”are equivalences.

APV

8516-14

Edition 1.0.1 March / 2020

7/42

TechnoAP Co., Ltd.

１．１． Specification

1. Analog Input

-Number of Channel: 16 CH.

-Input Range: ±1 V

-Input Impedance: 50 Ω

2. ADC

-Sampling Frequency: 500 MHz

-Resolution: 14-bit

-SNR: 68.3dBFS@605 MHz

3. Performance

-QDC Throughput: More than 1 Mcps

-Time Resolution: 7.8 ps (LSB)

4. MCA

-Measurement Mode: Wave Mode, Histogram Mode, List Mode

-Event Transmission Rate: Approx. 10 Mbyte / sec.

In case of 10 Byte (80 Bit) / Event, CH. total is 1 Mcps.

5. Communication I / F

-LAN I/F: Ethernet TCP / IP 1000 Base-T (List data acquisition), UDP/IP (config data, states data sent /

received)

6. Form

-VME type: VME1U, 20mm (W) x 262mm (H) x 187mm (D), About 460g

7. Wattage

+5V: 6.0 A (Max.)

+12V: 0.8 A (Max.)

-12V: 0.4 A (Max.)

１．２． Operation System Requirements

・Microsoft Windows 7 or later

１．３． Revision History

Edition

Conteint

Date

1.0.0

First Edition

10 December 2019

1.0.1

Second Edition

4 March 2020

Edition 1.0.1 March / 2020

8/42

TechnoAP Co., Ltd.

２． External

No.

Name

Contents

LED

P: Power ON

V: Not used

E: Not used.

CH1 to CH16

LEMO connector for signal input.

Input range: ± 1V, input impedance: 50Ω.

SYNC-O

LEMO connector for synchronous timing signal output.

Outputs a timing signal for adjusting the time between boards.

SYNC-I

LEMO connector for synchronous timing signal input.

Input a timing signal to adjust the time between boards.

CLK-O

LEMO connector for external clock signal output.

Outputs a 25MHz TTL signal.

CLK-I

LEMO connector for external clock signal input.

It can be operated using an external clock.

Turn on the power after inputting the 25MHz TTL signal.

VETO

LEMO connector for external VETO signal input.

Disable data acquisition during “High”.

GATE

LEMO connector for external GATE signal input.

Input TTL signal.

Enables data acquisition while the input is “High”.

LAN

RJ45 connector for Ethernet cable.

1000Base-T.

Note: Use the SYNC-O and SYNC-I interconnected with a cable.

（１）

（２）

（３）

（４）

（６）

（５）

（７）

（９）

（８）

Edition 1.0.1 March / 2020

9/42

TechnoAP Co., Ltd.

３． Preparation

３．１． Display

Recommended monitor resolution is more than FullHD (1920 x 1080)

３．２． Installation of the application

The application forAPV8516-14 (hereinafter this application) runs on Windows. To use this software, it is necessary

to install the EXE (executable file) of this application and the LabVIEW Runtime Engine of National Instruments on

the PC used for measurement.

Installation of this application is performed by the installer included in the attached CD. The installer includes an

EXE (executable) file and the LabVIEW Run-Time Engine, which can be installed at the same time.

The installation procedure is as follows.

1. Log in to Windows with administrator authority.

2. Execute “Setup.exe” in the “Installer” folder on the attached CD-ROM. Proceed with the installation interactively.

The default installation destination is “C: ¥ TechnoAP”.

3. Execute "Start Button"-"TechnoAP"-"APV8516-14".

To uninstall, select "APV8516-14" from "Add or Remove Programs" and delete it.

Recommended computer specifications are follows,

Microsoft Corp. Windows 7 32-bit or later

Recommended screen resolution: FullHD (1920 x 1080) or more.

３．３． Power ON and IP Connection Confirmation

1. Confirm power on the PC and Switching Hub, and ON the VME power switch.

2. Please wait about 30 seconds

3. Execute the ping command at the Windows command prompt to check whether the device and the PC can be

connected. Start the windows application “cmd.exe”. The IP address of this device shows on the board. The

defalt of these boards is as follows.

“ping 192.168.10.128”

“ping 192.168.10.129”

“ping 192.168.10.130”

Edition 1.0.1 March / 2020

10/42

TechnoAP Co., Ltd.

*Screen when communication settings are CORRECT

*Screen when communication settings are INCORRECT

Indice

Altri manuali TechnoAP Strumento di misura

TechnoAP

TechnoAP APV8M44 Manuale utente

TechnoAP

TechnoAP APU101 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente