Tektronix P6405 Manuale utente

COMMITTED TO EXCELLENCE

Instructions

P6405

010-6405-01

P6405 DATA ACQUISITION PROBE

OPERATOR'S PART

DESCRIPTION

The P6405 is a passive data probe used with the SA 501 Signature Analyzer to sample digital data

from various logic families. The Analyzer compares data from the probe with its own Threshold HI and

Threshold LO reference levels and then sends signals back to the probe to illuminate the appropriate logic

level lamp(s).

The P6405 contains:

• Two logic level lamps (red and green)

A preset compensation capacitor

• Slide switch (10 MQ or 50 kQ input impedance)

• Momentary contact switch (system reset)

• 1.5

meter cable

• 6

pin connector

070-3620-00

All right;. re,erved.

APRIL 1981

P6405 Data Acquisition Probe

Characteristics

Attenuation

Input Resistance

Input Capacitance

Maximum Input Voltage

Characteristics

Temperature range

Operating

Non-operating

Altitude

Operating

Non-operating

Humidity

Non-operating

Shock

Non-operating

SPECIFICATION

·Etectrical

Description

10X ±5%

Switch selection of:

-10 Mil ±5% to gnd

-50 kQ ±3% to 1.4 V

14 pF (approx)

±40 V de+ peak ac

Envirc11,mental Description

-15°C to +55°C (+5°F to +131°F)

-62 °C to +85°C {-80°F to +185°F)

to 4500 m (15,000

ft)

to 15,000 m (50,000

ft)

5 cycles, 120 hrs 95-97% relative

3o•c

60°C

500 g·s, Half sine 1ms duration

Characteristics

Net weight (including accessories)

Length

Total

Cable

Connector pin identification

P6405 Data Acquisition Probe

Physical

113 grams (4.0 oz)

1.64 m

(64.5 in)

1.5

m (59 in)

Description

pin 1-Coax center cond.

2-50 kfl

(Switchable)

3-Red ind. light

4-Green ind. light

5-Reset Sw. sense

6-lnd. light common

Connector shell - coax shield.

P6405 Data Acquisition Probe

OPERATING INSTRUCTIONS

The P6405 data probe is designed to work with the SA 501 Signature Analyzer.

Data Probe Controls

1. Reset

Clears a single-event signature from the display.

2. HIGH/LO

Selects either: 1OMn to ground

50 kn to 1.4 v

Data Probe Indicators

1. LOGIC HIGH (RED)

ON indicates input greater than high threshold.

OFF indicates input less than high threshold.

Flashing indicates pulsing input transitioning through high threshold.

2. LOGIC LOW (GREEN)

On indicates input is less than the low threshold.

Off indicates input is greater than the low threshold.

Flashing indicates a pulsing input transitioning through low threshold.

OPERATING PROCEDURE

Connect the data probe to the SA 501 by inserting the probe's 6-pin Lerno connector into the Data

Input socket (marked P6405 on the analyzer's front panel).

Set the slide switch to the appropriate position for the unit under test.

• When the slide switch is in the 50 kn position, a 50 kn resistor inside the probe is connected be-

tween the probe tip and 1.4 V. Thus, the probe tip is biased to 1.4 V whenever the line being tested

is in a high impedance state. This keeps 3-state busses from wandering aimlessly when they are off.

When the SA 501 is set for TTL thresholds, it ignores a 1.4 V threshold voltage and, thus, will not be

triggered during a 3-state high impedance situation.

P6405 Data Acquisition Probe

The Reset button pulls pin 5 on the Lerno connector high. When the SA 501 sees this line move, it

resets its CRC and character latches.

The green and red lamps are driven from the SA 501.

• The green lamp is lit whenever the input data goes below the LO Threshold.

• The red lamp is lit whenever the data signal goes above the HI Threshold.

STANDARD ACCESSORIES

A variety of items to aid in the use of the P6405 are provided as standard accessories

(see Accessories in the parts list at the rear of this manual).

P6405 Data Acquisition Probe

SERVICE

WARNING I

The following servicing instructions are for use by qualified personnel only. To avoid personal

injury, do not perform any servicing other than that contained in the operating instructions unless

you are qualified to do so.

INTRODUCTION

The P6405 is a passive data probe for the SA 501 Signature Analyzer.

Theory of Operation

The data input portion of the P6405 is made up of a thick film RC device plus a trimmer capacitor (C2)

and the coax cable.

The thick film device (R1, C1) determines, to a great degree, the impedance the circuit under test sees

at the P6405 probe tip. The total input resistance of the signature analyzer is made up of the 1

input in

the SA 501 and the 9Ml1 R1 making the total input resistance 10 Mr!.

A 50 kU resistor, R2, can be connected via switch S1 to a 1.4 V line from the analyzer. When connect-

ed to 1.4 V, this resistor pulls high impedance (3-state) lines toward 1.4 V, which is between the TTL HI and

TTL LO Thresholds on the SA 501.

The indicator lamps are long life, 5 V, 60 mA bulbs. They are driven by the SA 501.

Momentary s,""itch S2 connects pin 5 on the Lerno connector (reset sense line)

the lamp's common

line.

P6405 Data Acquisition Probe

Performance Check and Adjustment

Equipment Needed

• Pulse Generator and appropriate termination.

Example: TEKTRONIX PG 502

• 100 MHz Scope

Example: TEKTRONIX 4658

• SA 501 with data input normalized to 1 Mn paralleled by 26 pF. (Normalization is done with the RC

Normalizer 067-1035-00).

• DC to 100 MHz, l0X Probe

Example: TEKTRONIX P6105

Performance Check

1. Remove the cover from the Input Board side of the SA 501 (the left side, when facing the front of

the instrument).

2. Install the TM 500 test equipment in a mainframe, making sure that the left side of the SA 501 is

accessible.

3. Turn on all the test equipment and let it warm up for 30 minutes.

4. Attach channel A (0.5 V/div) of the oscilloscope to the signal generator and set the generator for a

1 kHz square wave at 2 V peak-to-peak.

5. Connect the P6405 to the SA 501 and use the data probe to sample the 1 kHz square,wave.

6. Attach the oscilloscope channel B (50 mV/div) to A2TP1062 (signal)and A2TP1057 (ground) by

means of the P6105. Peak- to-peak aberrations caused by the probe and the SA 501 input should not

exceed 10% of the peak-to-peak signal on A2TP1062. (Note, the signal inside the SA 501 will be 1/10

that of the generator.)

P6405 Data Acquisition Probe

Adjustment

1. It the peak-to-peak aberrations are greater than 10%, do the adjustment in step 2.

NOTE

Before adjusting C2 to null out aberrations in the waveform, make sure that the SA 501's input

has been calibrated with an RC Normalizer, otherwise the problem may be in the SA 501.

Adjustment of the compensation circuit inside the probe to ciean up the input of an out-of-

tolerance SA 501 will make it necessary to readjust the probe while it is attached to another

SA501.

2. Calibrate tt,s probe by adjusting C2 with a smaii-tipped non-magnetic screwdriver tor minimum

waveform distortion.

Reassembling the Instrument

• Remove the scope probe and repiace the SA 601 s side panel.

MAINTENANCE

Because of the speciil fixtures required and the delicate nature of the internal assembly,

individual components w~th1n the probe head are not considered customer replaceable parts.

If the probe is damagedor fails, please return it to your local Tektronix Field Office or

representative for repair.

P6405 Data Acquisition Probe

REPLACEABLE

PARTS

PARTS ORDERING INFORMATION

Replacement parts are available from or through your local Tektronix, Inc. Field Office

or representative.

Changes to Tektronix !nstrun,ents are sometiri:ies made to accommodate improved

components as they become available, and to give'"you the benefit of the latest circuit

improvements developed in our engineering department. It is therefore important, when

ordering parts, to include the following information in your order: Part number, instrument

type or number, serial number, and modification number if applicable.

If a part you have ordered has been replaced with a new or improvP.d part, your local

Tektronix, Inc. Field Office or representative will contact you concerning any change in part

number.

Change information, if any, is located at the rear of this manual.

SPECIAL NOTES AND SYMBOLS

X000 Part first added at this serial number

00X Part removed after this serial number

ITEM NAME

In the Parts List, an Item Name is separated from the description by a colon (:).

Because of space limitations, an Item Name may sometimes appear as incomplete. For

further Item Name identification, the U.S. Federal Cataloging Handbook H6-1 can be

utilized where possible.

ABBREVIATIONS

ACTR ACTUATOR PLSTC PLASTIC

ASSY ASSEMBLY QTZ QUARTZ

CAP CAPACITOR RECP RECEPTACLE

GER CERAMIC RES RESISTOR

CKT CIRCUIT RF RADIO FREQUENCY

COMP COMPOSITION SEL SELECTED

CONN CONNECTOR SEMICOND SEMICONDUCTOR

ELCTLT ELECTROLYTIC SENS SENSITIVE

ELEC ELECTRICAL VAR VARIABLE

INCAND INCANDESCENT WW WIREWOUND

LED LIGHT EMITT-ING DIODE XFMR TRANSFORMER

NONWIR NON WIREWOUND XTAL CRYSTAL

P6405 Data Acquisition Probe

Fig.&

Index

No.

-1

-2

-3

-4

-5

-6

-7

-8

-9

-10

-11

Tektronix

PartNo.

010-6405-01

010-64 05-00

344-0046-00

175-0124-01

175-0125-01

206-0254-01

166-0404-01

015-0201-04

206-0222-00

015-0325-00

016-0521-00

206-0252-02

070-3620-00

Serial/ModelNo.

Eff Oscont

REPLACEABLEPARTSLIST

Qty 1 2 3 4 5 Name& Description

1 PROBE,LOGIC:l.5M L W/ACCESSORIES

1 • PROBE,LOGIC:l.5M L

STANDARDACCESSORIES

2 CLIP,ELECTRICAL:ALLIGATORTYPE,W/COVER

1 LEAD,ELECTRICAL:PROBEGND,5 INCHESL

1 LEAD,ELECTRICAL:PROBEGND,12 INCHESL

2 TIP,PROBE:LOGIC,MOLDEDW/PLASTIC

1 TUBE,INSULATOR:

1 TIP,PROBE:IC TEST, PKGOF 10

2 TIP,PROBE:MICROCIRCUITTEST

1 ADAPTOR,PROBE:PROBETO CONNECTORPINS

1 POUCH,ACCESSORY

1 TIP,PROBE:P6405, SLIP-ON

1 SHEET,TECHNICAL:INSTRUCTION010-6405-00

CROSSINDEX-MFR.CODENUMBERTOMANUFACTURER

Mfr. Code Manufacturer

05006 TWENTIETHCENTURYPLASTICS, INC.

80009 TEKTRONIX,INC.

Address

415 E WASHINGTONBLVD.

PO BOX500

Mfr

Code Mfr Part Number

80009 010-6405-01

80009 010-6405-00

80009 344-0046-00

80009 175-0124-01

80009 175-0125-01

80009 206-0254-01

80009 166-0404-01

80009 015-02 01-04

80009 206-0222-00

80009 015-0325-00

05006 OBD

80009 206-0252-02

80009 070-3620-00

City, State, Zip

LOSANGELES,CA 90015

BEAVERTON,OR 97077

Indice

Altri manuali Tektronix Strumento di misura

Tektronix

Tektronix 491 Manuale utente

Tektronix

Tektronix 067 -0794-00 Manuale utente

Tektronix

Tektronix TLA 7F1 Manuale utente

Tektronix

Tektronix TMSSC2 Manuale utente

Tektronix

Tektronix WVR5200 Series Istruzioni di installazione e manutenzione

Tektronix

Tektronix TLA7000 Series Manuale utente

Tektronix

Tektronix 1L10 Manuale utente

Tektronix

Tektronix 7L5 Manuale utente

Tektronix

Tektronix 7L5 Manuale

Tektronix

Tektronix VM700T Manuale utente

Tektronix

Tektronix 5D10 Manuale utente

Tektronix

Tektronix 7D01 Manuale utente

Tektronix

Tektronix TIVH Series Manuale utente

Tektronix

Tektronix CSA8000B Series Manuale utente

Tektronix

Tektronix Keithley SourceMeter 2461 Manuale utente

Tektronix

Tektronix P6231 Manuale utente

Tektronix

Tektronix TLA7N Series Manuale utente

Tektronix

Tektronix 475 Manuale utente

Tektronix

Tektronix KEITHLEY 2450-EC Manuale utente

Tektronix

Tektronix THM550 Manuale utente

Tektronix

Tektronix 1200C01 Manuale utente

Tektronix

Tektronix SPECMON3 Manuale utente

Tektronix

Tektronix VM700T Manuale operativo e di manutenzione

Tektronix

Tektronix DSA8300 Manuale

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente