Tektronix TDS 420A Manuale utente

Service Manual

TDS 420A, TDS 430A & TDS 460A

Digitizing Oscilloscopes

S/N B080000 and above

070-9703-06

Revsion A

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

WARRANTY

Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and workmanship

for a period of three (3) years from the date of shipment. If a product proves defective during this warranty period,

Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a

replacement in exchange for the defective product.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the

warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for

packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid.

Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any

other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate

maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting

from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair

damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction

caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or integrated with other

products when the effect of such modification or integration increases the time or difficulty of servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR

IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO

REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO

THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE

LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE

OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH

DAMAGES.

Contacting Tektronix

Phone 1-800-833-9200*

Address Tektronix, Inc.

Department or name (if known)

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

Web site www.tektronix.com

Sales support 1-800-833-9200, select option 1*

Service support 1-800-833-9200, select option 2*

Technical support Email: techsupport@tektronix.com

1-800-833-9200, select option 3*

1-503-627-2400

6:00 a.m. -- 5:00 p.m. Pacific time

*This phone number is toll free in North America. After office hours, please leave a

voice mail message.

Outside North America, contact a Tektronix sales office or distributor; see the

Tektronix web site for a list of offices.

TDS 420A, TDS 430A & TDS 460A Service Manual i

Table of Contents

List of Figures iii............................................

List of Tables vi.............................................

General Safety Summary ix...................................

Service Safety Summary xi....................................

Preface xiii...................................................

Introduction xvi..............................................

Before Servicing xvi.................................................

Strategy for Servicing xvi.............................................

Tektronix Service xvii................................................

Specifications

Product Description 1--1........................................

Nominal Traits 1--7............................................

Warranted Characteristics 1--15..................................

Typical Characteristics 1--23.....................................

Operating Information

Installation 2--1...............................................

Supplying Operating Power 2--1........................................

Operating Environment 2--3...........................................

Applying and Interrupting Power 2--4....................................

Repackaging Instructions 2--5..........................................

Installed Options 2--5.................................................

Operating Information 2--7.....................................

Screen Layout 2--7...................................................

Basic Procedures 2--7.................................................

Theory of Operation

Theory of Operation 3--1.......................................

Logic Conventions 3--1...............................................

Module Overview 3--1................................................

Performance Verification

Performance Verification Procedures 4--1.........................

Brief Procedures 4--5...........................................

Self Tests 4--5.......................................................

Functional Tests 4--7.................................................

Performance Tests 4--15.........................................

Prerequisites 4--15....................................................

Equipment Required 4--16..............................................

Test Record 4--18.....................................................

Table of Contents

ii TDS 420A, TDS 430A & TDS 460A Service Manual

Signal Acquisition System Checks 4--20...................................

Time Base System Checks 4--34.........................................

Trigger System Checks 4--38............................................

Output Signal Check 4--53..............................................

Sine Wave Generator Leveling Procedure 4--55.............................

Adjustment Procedures

Adjustment Procedures 5--1.....................................

Requirements for Performance 5--1......................................

Usage 5--2.........................................................

Equipment Required 5--5..............................................

Adjustment Instructions 5--7...........................................

Probe Adjustment 5--10................................................

Monitor Assembly Adjustment 5--21.....................................

Maintenance

Maintenance 6--1..............................................

Related Maintenance Procedures 6--1....................................

Preparation 6--2.....................................................

Inspection and Cleaning 6--4...........................................

Removal and Installation Procedures 6--9.........................

Preparation — Please Read 6--9........................................

Access Procedure 6--13................................................

Procedures for Module Removal and Installation 6--23.......................

Disassembly for Cleaning 6--71..........................................

Troubleshooting 6--75...........................................

Diagnostics 6--75.....................................................

Firmware Updates 6--76................................................

Troubleshooting Equipment 6--77........................................

Options

Electrical Parts List

Diagrams

Mechanical Parts List

Table of Contents

TDS 420A, TDS 430A & TDS 460A Service Manual iii

List of Figures

Figure 1--1: TDS 400A Dimensional Drawing 1--13...................

Figure 2--1: Map of Display Functions 2--8........................

Figure 4--1: Map of Display Functions 4--3........................

Figure 4--2: Verifying Adjustments and Signal Path Compensation 4--6

Figure 4--3: Universal Test Hookup for Functional Tests 4--8.........

Figure 4--4: Initial Test Hookup 4--20..............................

Figure 4--5: Initial Test Hookup 4--23..............................

Figure 4--6: Initial Test Hookup 4--26..............................

Figure 4--7: Measurement of Analog Bandwidth 4--29................

Figure 4--8: Initial Test Hookup 4--31..............................

Figure 4--9: Measurement of Channel Delay 4--33....................

Figure 4--10: Initial Test Hookup 4--34.............................

Figure 4--11: Measurement of Accuracy — Long-Term and

Delay-Time 4--37............................................

Figure 4--12: Initial Test Hookup 4--38.............................

Figure 4--13: Initial Test Hookup 4--41.............................

Figure 4--14: Measurement of Trigger Sensitivity 4--43...............

Figure 4--15: Initial Test Hookup 4--45.............................

Figure 4--16: Confirming Auxiliary Triggering at Maximum

Triggering Frequency 4--46...................................

Figure 4--18: Initial Test Hookup 4--49.............................

Figure 4--19: Adjusting Sync Pulse Amplitude 4--51..................

Figure 4--20: Measurement of Video Sensitivity 4--52.................

Figure 4--21: Initial Test Hookup 4--54.............................

Figure 4--22: Measurement of Probe Compensator Limits 4--55........

Figure 4--23: Sine Wave Generator Leveling Equipment Setup 4--56....

Figure 4--24: Equipment Setup for maximum Amplitude 4--57.........

Figure 5--1: Hookup for Probe Compensation 5--10..................

Figure 5--2: Performing Probe Compensation 5--11..................

Figure 5--3: Proper and Improper Probe Compensation 5--12..........

Figure 5--4: Exposing the Inner Probe Tip 5--13.....................

Figure 5--5: Initial Test Hookup 5--13..............................

Figure 5--6: Exposing the Probe Body 5--16.........................

Table of Contents

iv TDS 420A, TDS 430A & TDS 460A Service Manual

Figure 5--7: Initial Test Hookup 5--16..............................

Figure 5--8: Probe Test Hookup 5--18..............................

Figure 5--9: Locations of Probe Adjustments 5--19...................

Figure 5--10: Adjustments vs. Front-Corner Response 5--20...........

Figure 5--11: Monitor Adjustment Locations 5--23...................

Figure 5--12: Five and Ten Percent Luminance Patches 5--24..........

Figure 5--13: Composite Pattern for Focusing 5--25..................

Figure 6--1: Oscilloscope Orientation 6--11..........................

Figure 6--2: Cabinet and Front-Panel Mounted Modules 6--16.........

Figure 6--3: Internal Modules 6--19................................

Figure 6--4: Cables and cable routing, B010100 -- B079999 6--22.......

Figure 6--5: Cables and cable routing, B080000 & up 6--23............

Figure 6--6: Knob and shaft removal 6--25..........................

Figure 6--7: Line fuse and line cord removal 6--26...................

Figure 6--8: Front cover, rear cover, cabinet, emi gasket,

and cabinet handle and feet removal 6--28.......................

Figure 6--9: Trim ring, menu elastomer, and menu

buttons removal 6--31........................................

Figure 6--10: EMI gasket removal and installation 6--33..............

Figure 6--11: Disk drive removal 6--34.............................

Figure 6--12: A06 Front-Panel assembly, ESD shield,

and menu flex and probe code flex circuits removal 6--36..........

Figure 6--13: Disassembly of the front-panel assembly 6--37...........

Figure 6--14: A05 Attenuator removal 6--40.........................

Figure 6--15: A26 Monitor assembly removal 6--43...................

Figure 6--16: A08 Jumper board assembly, D1 Bus,

and board supports removal 6--44.............................

Figure 6--17: A03 CPU removal 6--46..............................

Figure 6--18: A02 Display assembly removal 6--48....................

Figure 6--19: A09 DSP assembly removal 6--49......................

Figure 6--20: A01 Backplane assembly and its mount removal 6--51.....

Figure 6--21: Battery removal 6--54................................

Figure 6--22: Power factor correction module

removal, B080000 & up 6--56.................................

Figure 6--23: A24 Low voltage power supply

removal, B080000 & up 6--59.................................

Figure 6--24: A25 Low voltage power supply

removal, B010100 -- B079999 6--61.............................

Figure 6--25: Fan and fan mount removal 6--64......................

Table of Contents

TDS 420A, TDS 430A & TDS 460A Service Manual v

Figure 6--26: Line filter removal 6--65..............................

Figure 6--27: Auxiliary power supply

removal, B010100 -- B079999 6--68.............................

Figure 6--28: A04 Acquisition Board Removal 6--70..................

Figure 6--29: Accessing the protection switch 6--76...................

Figure 6--30: Console port connections 6--79........................

Figure 6--31: Primary Troubleshooting Procedure 6--80...............

Figure 6--32: A03 CPU Board Connector P1 6--81....................

Figure 6--33: Module Isolation Troubleshooting Procedure 6--82.......

Figure 6--34: Low Voltage Power Supply

Troubleshooting Procedure 6--84..............................

Figure 6--35: Power Supply Overload

Troubleshooting Procedure 6--86..............................

Figure 6--36: A25 Low Voltage Power

Supply Module (Right Side) 6--87..............................

Figure 6--37: Monitor Troubleshooting Procedure 6--88...............

Figure 6--38: Horizontal and Vertical Sync Signals 6--89..............

Figure 6--39: A Video Signal with White, Black,

and Blanking Levels 6--89....................................

Figure 6--40: A26 Monitor Connector J440 6--90.....................

Figure 6--41: A07 Auxiliary Power Connectors J4 and J7 6--90.........

Figure 6--42: A02 Display Connector J2 6--91.......................

Figure 6--43: Processor/Front Panel Troubleshooting Procedure 6--92...

Figure 6--44: A06 Front Panel Board Power Connectors

J101 and J106 6--93.........................................

Figure 6--45: Attenuator/Acquisition Troubleshooting Procedure 6--94..

Figure 6--46: A08 Jumper and A05 Attenuator Boards

Signal Locations 6--95.......................................

Figure 6--47: Acquisition and Attenuator Power

Troubleshooting Procedure 6--96..............................

Figure 6--48: A04 Acquisition Board Power Connector 6--97...........

Figure 6--49: Backplane Troubleshooting Procedure 6--98.............

Figure 6--50: A01 Backplane Module 6--100..........................

Figure 6--51: I2C Isolation Troubleshooting Procedure 6--101...........

Figure 6--52: Console Troubleshooting Procedure 6--102...............

Figure 9--1: TDS 400A Interconnections, B010100 -- B079999 9--2.....

Figure 9--2: TDS 400A Interconnections, B010100 -- B079999 (Cont) 9--3

Figure 9--3: TDS 400A Block Diagram, B010100 -- B079999 9--4.......

Figure 9--4: TDS 400A Block Diagram, B010100 -- B079999 (Cont) 9--5

Table of Contents

vi TDS 420A, TDS 430A & TDS 460A Service Manual

Figure 9--5: TDS 400A Interconnections, B080000 & up 9--6..........

Figure 9--5: TDS 400A Interconnections, B080000 & up (Cont.) 9--7...

Figure 9--6: TDS 400A Block Diagram, B080000 & up 9--8...........

Figure 9--6: TDS 400A Block Diagram, B080000 & up (Cont.) 9--9....

Figure 10--1: External and front panel modules 10--7.................

Figure 10--2: Internal modules (B010100 - B079999) 10--9.............

Figure 10--3: Internal modules (B080000 - Up) 10--11..................

Figure 10--4: Cables and routing (B010100 - B079999) 10--13...........

Figure 10--5: Cables and routing (B080000 - Up) 10--15................

Altri manuali per TDS 420A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tektronix Apparecchiature di prova

Tektronix

Tektronix K15 Manuale

Tektronix

Tektronix BERTScope Manuale

Tektronix

Tektronix 1S1 Manuale utente

Tektronix

Tektronix MDO32 Manuale di istruzioni

Tektronix

Tektronix P6137 Manuale utente

Tektronix

Tektronix P6015A Manuale utente

Tektronix

Tektronix P6458 Manuale utente

Tektronix

Tektronix THS3024 Manuale utente

Tektronix

Tektronix 549 Manuale utente

Tektronix

Tektronix 2465A Manuale utente

Tektronix

Tektronix 7844 Manuale utente

Tektronix

Tektronix MSO2000 Series Manuale utente

Tektronix

Tektronix TDS3012C Manuale utente

Tektronix

Tektronix 432 Manuale di servizio

Tektronix

Tektronix TBS1000B Series Manuale utente

Tektronix

Tektronix 2246 1Y Manuale utente

Tektronix

Tektronix MSO4000 Series Manuale operativo e di manutenzione

Tektronix

Tektronix TriMode P7504 Manuale

Tektronix

Tektronix TBS2000B Series Manuale utente

Tektronix

Tektronix 7704A Manuale utente

Tektronix

Tektronix TDS5000 Series Manuale utente

Tektronix

Tektronix 515 Manuale utente

Tektronix

Tektronix 222 Manuale utente

Tektronix

Tektronix TDS 420A Manuale di servizio

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente