Tektronix TDS 500C Manuale utente

Supplement

TDS 500C, TDS 600B & TDS 700C

Digitizing Oscilloscopes

071-0090-01

This document supports firmware version 5.2 and

above.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

Printed in the U.S.A.

Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TDS 500C, TDS 600B & TDS 700C Supplement 1

Introduction

This document contains three supplements to the TDS 500C, TDS 600B, and

TDS 700C manuals:

TDS 580C Supplement provides information that extends the TDS 500C,

TDS 600B, and TDS 700C manuals to cover a new oscilloscope model, the

TDS 580C Digitizing Oscilloscope. See page 3.

Version 5.2 Firmware Supplement provides information that extends the

manuals to cover the new or changed functions that are available in the

TDS 500C and TDS 700C oscilloscopes, starting with firmware version 5.2.

See page 5.

Option 1G Supplement provides information that extends the manuals to

cover two oscilloscope models, the TDS 540C and TDS 754C Option 1G

Oscilloscopes. See page 29.

Introduction

2TDS 500C, TDS 600B & TDS 700C Supplement

TDS 500C, TDS 600B & TDS 700C Supplement 3

TDS 580C Supplement

The TDS 500C, TDS 600B, and TDS 700C model oscilloscope manuals also

cover an oscilloscope model that is not mentioned in those manuals, the

TDS 580C.

This supplement lists the differences between the TDS 580C and the TDS 784C,

which is the model that the TDS 580C is most like.

Except for the differences shown in the table below, The TDS 580C is identical

to a TDS 784C. Most of the information in your user manual (and other TDS

documents) that applies to the TDS 784C, also applies to the TDS 580C.

Like the TDS 784C, the TDS 580C provides four full-function channels,

digitizing rates to 4 GS/second, a 1 GHz analog bandwidth, and up to 50 K

record lengths (or longer with options 1M or 2M). The table below lists the key

areas where the TDS 784C and the 580C differ:

Feature 784C 580C

Display Color Monochrome

FFT Yes Optional(2F)

RS232 and Centronics Port Yes Optional(13)

Accessory Pouch Standard Available

(016-1268-00)

All options listed for the TDS 784C are available for the TDS 580C. The

TDS 784C, and the TDS 580C ships without probes. The probe options are:

Option 24. Add four P6139A passive oscilloscope probes.

Option 26. Add four P6245 1.5 GHz FET oscilloscope probes.

The option 1G, detailed in Option 1G Supplement in this document, is not

available for the TDS 580C.

The TDS 580C comes with the firmware features listed in Version 5.2 Firmware

Supplement in this document; no upgrade is required. See page 5.

Key Features

Options

Firmware

TDS 580C Supplement

4TDS 500C, TDS 600B & TDS 700C Supplement

The TDS 500C, TDS 600B, and TDS 700C Service Manual (optional accessory)

applies to the TDS 580C.

Use the part number listed for the TDS 784C when replacing the following parts:

Circuit Board Assembly: Acquisition A10

Front Panel Assembly A12

Use the part number listed for the TDS 520C, TDS 540C, TDS 620B, and

TDS 680B when replacing the following parts:

Display, Monochrome: 7-Inch A20

Filter, Lt, Crt: 6.525 X 5.225, ESP, EMC

Retainer, Filter: Dust Seal Assembly, Lexan

Use part number 334-8551-01 when replacing the Front-Panel Identification

Label.

Service Information

TDS 500C, TDS 600B & TDS 700C Supplement 5

Version 5.2 Firmware Supplement

This supplement describes new or changed functions that are available starting

with firmware version 5.2.

Masks

Masks now include the following functions.

Table 1 contains a complete list of available masks.

Table 1: Standard masks

SONET

SDH ITU-T T1.102 Fibre channel Video Ethernet Miscellaneous

None None None None None None None

OC1/STM0

51.84Mb/s DS-0 Sgl

Single

64.4kb/s

DS1

1.544Mb/s FC133

Optical132.8 Mb/s 4fsc NTSC “D2”

143.18Mb/s GigabitEthernet

Optical 1.25 Gb/s FDDI Halt

125Mb/s

OC3/STM1

155.52Mb/s DS-0 Dbl

Double 64 kb/s DS1A

2.048Mb/s FC266

Optical265.6 Mb/s 4:2:2 “D1”

270Mb/s 100Base-TX

UTP 125 Mb/s

OC12/STM4

622.08Mb/s DS-0 Data

DataContra

64 kb/s

DS1C

3.152Mb/s FC531

Optical531.2 Mb/s 4:2:2SMPTE

259M-D

360Mb/s

100Base-TX

STP 125 Mb/s

DS-0 Tmg

Timing 64 kb/s DS2

6.312Mb/s FC1063

Optical1.0625 Gb/s 10 Base-T Idle (IDL)

Time Details 10 Mb/s

DS-1Rate

1.544Mb/s DS3 Full Mask

44.736Mb/s FC133E

Electrical132.7 Mb/s 10 Base-T Idle (IDL)

Volt Details 10 Mb/s

DS-3Rate

44.736Mb/s DS3 TimeDetails

44.736Mb/s FC266E

Electrical265.6 Mb/s 10 Base-T Idle (IDL)

Full Mask 10 Mb/s

E1 Sym

Sym Pair

2.048Mb/s

DS4NA

139.26Mb/s FC531E

Electrical531.2 Mb/s 10 Base-T Link Test

Time Details 10 Mb/s

E1 Coax

CoaxPair

2.048Mb/s

DS4NA Mx

MaxOutput

139.26Mb/s

FC1063E

Electrical

1.0625Gb/s

10 Base-T Link Test

Volt Details 10 Mb/s

8.448Mb/s STS-1 Eye

Eye 51.84 Mb/s 10 Base-T Link Test

Full Mask 10 Mb/s

34.368Mb/s STS-1

Pulse 51.84 Mb/s

Available Masks

Version 5.2 Firmware

6TDS 500C, TDS 600B & TDS 700C Supplement

Table 1: Standard masks (Cont.)

SONET

SDH MiscellaneousEthernetVideoFibre channelT1.102ITU-T

E4 0

Binary 0

139.26Mb/s

STS-3

155.52Mb/s

E4 1

Binary 1

139.26Mb/s

STS-3 Mx

MaxOutput

155.52Mb/s

E5 CEPT

565Mb/s

STM1E 0

Binary 0

155.52Mb/s

STM1E 1

Binary 1

155.52Mb/s

If on, mask pass/fail testing displays the results in the Pass/Fail Testing side

menu. To start mask pass/fail testing, press MEASURE ➞Measure (main) ➞

Masks (pop-up) ➞Mask Counting (main). Then toggle Pass/Fail Test (side) to

On.

The Pass/Fail Test side menu displays the testing status:

Passing is displayed if, for the requested number of acquired waveforms, the

number of hits does not exceed the number of hits specified in the failure

threshold

Failed is displayed if there are hits greater than or equal to the Pass/Fail

Failure Threshold in the masks in the requested number of acquired

waveforms

OFF Passed or OFF Failed is displayed when the test is complete, based on

the result of the test

Pass/fail testing turns on mask counting and resets the mask count to 0.

Hits greater than or equal to the Pass/Fail Failure Threshold are a test failure. To

set the threshold, press MEASURE ➞Measure (main) ➞Masks (pop-up) ➞

Mask Counting (main) ➞Pass/Fail Failure Threshold (side). Then use the

general purpose knob or keypad to set the failure threshold.

Pass Fail Testing

Set the Failure Threshold

Version 5.2 Firmware

TDS 500C, TDS 600B & TDS 700C Supplement 7

The test continues until the minimum number of waveforms has been acquired.

To set the minimum number of waveforms, press MEASURE ➞Mea-

sure (main) ➞Masks (pop-up) ➞Mask Counting (main) ➞Set Minimum

Number of Waveforms (side). Then use the general purpose knob or keypad to

set the number of waveforms.

The Pass/Fail Bell menu controls whether the mask pass/fail test rings a bell. To

control the Pass/Fail Bell, press MEASURE ➞Measure (main) ➞Masks

(pop-up) ➞Mask Counting (main). Then toggle Pass/Fail Bell (side) to Off,

On Failed, or On Completion.

Off does not ring a bell

On Completion rings the bell when the test is complete

On Failed rings the bell when a failure is detected and when the test is

complete

Use the procedures in your manual. Also, if a user mask is active, Autoset

adjusts the selected trace to match the last standard mask selected, if possible.

Use the HORIZONTAL POSITION control or the Time Base Position menu to

manually align the waveform to a mask. Adjusting the HORIZONTAL POSI-

TION resets mask counting.

Use Mask Margins to determine if your signal passes with a specific margin. To

set a mask margin do the following steps:

1. To enable mask margins, press MEASURE ➞Measure (main) ➞Masks

(pop-up) ➞Mask Margins (main). Then toggle Mask Margins (side) to

On or Off. If a user defined mask has more than three masks, turning on

mask margins will generate an error. Turning Mask Margins off will set the

Margin Percentage to 0%.

2. To set the margin percentage, press Margin Percentage (side). Then use the

general purpose knob or the keypad to set the percentage. Mask margin

percentage moves the mask boundaries to reflect the selected margin.

Negative margins make it easier to pass a mask test.

Set mask options to determine which waveform the masks are compared against,

to turn masks on or off, to enable Autoset to a mask, to enable offset adjustment

to masks, and to enable the digital waveform filter (see Figure NO TAG).

To select the channel that is compared against the selected mask, press MEA-

SURE ➞Measure (main) ➞Masks (pop-up) ➞Mask Options (main). Then

Set the Minimum Number

of Waveforms

Ringing the Bell

To Autoset the

Oscilloscope

Adjusting the Horizontal

Position

Setting Mask Margins

Setting Mask Options

Version 5.2 Firmware

8TDS 500C, TDS 600B & TDS 700C Supplement

toggle Mask Source (side) to Ch1, Ch2, Ch3, or Ch4. Mask Source is not

available in InstaVu II, because all on channels contribute to the mask.

To turn defined masks on or off, press MEASURE ➞Measure (main) ➞

Masks (pop-up) ➞Mask Options (main). Then toggle Mask Display (side)

ON or OFF.

To invert a DS1, DS1A, DS1C, DS2, DS3, E1 Sym, E1 Coax, E2, E3, STS-1,

STM1E, or E4 mask, press MEASURE ➞Measure (main) ➞Masks

(pop-up) ➞Mask Options (main). Then toggle Invert Mask (side) ON or OFF.

When ON and you select one of the above masks, the created mask is for a pulse

of opposite polarity to that of the standard mask.

Mask

Margins

OFF

Figure 1: Mask menu

NOTE. If you select Manual, some controls are automatically adjusted; if you

select Auto, a complete Autoset is performed. Also, if a user mask is active,

Autoset adjusts the selected trace to match the last standard mask selected, if

possible.

To control whether an autoset is performed when a standard mask is selected,

press MEASURE ➞Measure (main) ➞Masks (pop-up) ➞Mask Op-

tions (main). Then toggle Std Mask Autoset (side) to Auto or Manual.

Altri manuali per TDS 500C

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tektronix Apparecchiature di prova

Tektronix

Tektronix 2213 Istruzioni per il montaggio

Tektronix

Tektronix TDS5000B Series Manuale utente

Tektronix

Tektronix MSO54B Manuale utente

Tektronix

Tektronix DSA70000/B Series Manuale operativo e di manutenzione

Tektronix

Tektronix SC 502 Manuale utente

Tektronix

Tektronix 2445 Manuale utente

Tektronix

Tektronix MDO4000B Series Guida alla risoluzione dei problemi

Tektronix

Tektronix S-4 Manuale utente

Tektronix

Tektronix S-2 Manuale utente

Tektronix

Tektronix P5205 Manuale utente

Tektronix

Tektronix MDO4000C Series Manuale utente

Tektronix

Tektronix TAS 475 Manuale utente

Tektronix

Tektronix 507 Manuale utente

Tektronix

Tektronix 432 Manuale di servizio

Tektronix

Tektronix 2235 Manuale utente

Tektronix

Tektronix MSO3000 Series Manuale utente

Tektronix

Tektronix 200 Series Manuale utente

Tektronix

Tektronix Keithley CS-1546 Manuale utente

Tektronix

Tektronix 2440 Manuale utente

Tektronix

Tektronix MSO70000C/DX Manuale per l'uso e la cura

Tektronix

Tektronix 321 Series Manuale

Tektronix

Tektronix 177 Manuale utente

Tektronix

Tektronix TDS7000 Series Manuale

Tektronix

Tektronix Keithley 1754 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente