Teledyne GT Series Guida rapida

INSTRUCTION SHEET

Fig. 2 12V Power Socket - Top

Fig. 1 GT series instrument located in

(Individual Gases) Calibration Station

Calibration Station

INDIVIDUAL GASES - INSTALLATION & USE

GMI Part Number: 67109 (67109Q)

The automatic calibration station, Part No.

67109 with 6mm. ﬁttings (67109Q with 1

inch

ﬁttings),providesasafeandconvenientmethod

of calibrating the GT series instrument. The

calibration station for individual gases should

bemountedonaverticalsurfaceforbestresults.

Wall mounting the calibration station:

If wall mounting calibration station, hold unit

complete with backplate in required location on

wall then, using backplate as a template, mark

(4) hole positions on wall. Use (4) suitable screws

(and rawlplugs if positioning the unit on a brick

wall) to secure. The calibration station backplate

can be removed, if required, to mark hole

positions more accurately. Refer also to paragraph

3 below: permanent power cable connection.

Calibration station power supply

67109(Q):

There are three methods of providing power

to the GT series calibration station 67109(Q).

1. Via a 12V PSU (GMI Part No. 12444)

located in a socket on the top face of

the calibration station. Refer to Fig. 2.

2. Via a 12V vehicle power supply (GMI Part

No. 12988) also located in a socket on the top

face of the calibration station. Refer to Fig. 2.

3. Via permanent 12V power supply cable.

This requires removal of backplate before

wall mounting the unit, procedure as follows:

a) Remove (6) screws that attach backplate to the

calibration station.

b) Remove blanking plug from underside of unit.

c) Fit 20mm. ( 3

in.) cable gland - size to suit cable.

Note max. wire cross section area = 2.5mm2

d) Connect permanent 12V power supply cable to

J25 connector on calibration station PCB. (observe

correct polarity). Refer to Fig. 3.

e) Replace backplate then secure using (6) screws.

Calibration station power supply 67611(Q):

The GT series calibration station 67611(Q) is powered

via 12V power supply cable from PC Controller

unit. The PC Controller unit is powered via mains

cable (both cables are supplied with the unit).

1. The 12V power supply cable from PC controller is

located in a socket on the top face of the calibration

Fig. 2 12V Power Socket - Top station. Refer to Fig. 2.

Fig. 3 J25 Connector

Fig. 4 Instrument Location

Service & Calibration Division:

25 Cochran Close, Crownhill,

Milton Keynes, MK8 OAJ

Tel: +44 (0) 1908 568867

e-mail: [email protected]

As an ISO9001 approved company, Teledyne GMI Ltd’s quality assurance programmes demand the continuous assessment and improvement of

all Teledyne GMI products. Information in this leaﬂet could thus change without notiﬁcation and does not constitute a product speciﬁcation. Please

contact Teledyne GMI or their representative if you require more details.

Part Number 67295 Issue 6 (10/09/21)

Inchinnan Business Park,

Renfrew, PA4 9RG

Scotland, UK

Tel: +44 (0) 141-812 3211

e-mail: [email protected]

Calibration Station

Calibration Station Gas Supply:

The gases can be plumbed in by using nylon tubing and

connect these to swage connector gas inlets at the top of

the calibration station. Outer diameter is 6mm. ( 1

in.).

1. Air 5. H2S (if applicable)

2. PPM 6. - Empty -

3. LEL 7. - Empty -

4. CO (if applicable) 8. Vol. Gas

Swagelok connectors must be ﬁnger tightened then,

using two spanners, tighten a further 11

turns. Do

not overtighten.

A gas pressure of 590 to 690 mBar (8.5 to 10 PSI)

should be provided to these gas inlets.

Calibration station computer connection and driver software:

* The calibration station has a USB connector that can be easily connected to a free USB port on the

computer. (*not applicable to 67611 and 67611Q)

Install the software from the enclosed CD-ROM to initially set up the gases.

Start the software. The ﬁrst time you will be asked to select the com-port.

Install instrument in the Calibration Station

Make sure that the power contacts, on the back of the GT instrument and on the calibration station (shown

in Fig. 4), are clean and free of dirt / grease. As detailed on calibration station instructions label, carefully

position the GT in its docking location, as shown in Fig.1, with the bottom part ﬁrst, placing the extension

pole recess at the bottom of the GT so that it docks with the holding clip shown in Fig. 4. Push the instrument

backwards so that it is located between the two holding arms then engage the securing strap. Locate the

probe as shown in Fig. 1.

Follow the further instructions on the front of the calibration station.

www.TeledyneGFD.com

Altri manuali per GT Series

Questo manuale è adatto per i seguenti modelli

Altri manuali Teledyne Apparecchiature di prova

Teledyne

Teledyne LabMaster 10 Zi Series Manuale elenco delle parti

Teledyne

Teledyne T3DSO1000 Istruzioni operative

Teledyne

Teledyne T3DSO1000 Manuale utente

Teledyne

Teledyne HPM 4 Manuale utente

Teledyne

Teledyne 401 Manuale utente

Teledyne

Teledyne HDO8000A Manuale utente

Teledyne

Teledyne T3NFP3 Manuale utente

Teledyne

Teledyne T3CP100-2 Manuale utente

Teledyne

Teledyne LeCroy T3DSO2000A Series Manuale utente

Teledyne

Teledyne T703 Manuale utente

Teledyne

Teledyne T3EL15030 P Series Manuale utente

Teledyne

Teledyne T3DAQ1-16 Manuale utente

Teledyne

Teledyne FST-040 Manuale utente

Teledyne

Teledyne LeCroy Waverunner LT Series Foglio di istruzioni

Teledyne

Teledyne T3DSO3000 Manuale utente

Teledyne

Teledyne LeCroy T3DSO2000A Series Manuale utente

Teledyne

Teledyne Everywhereyoulook T3DSOH1000 Manuale utente

Teledyne

Teledyne 804A Manuale utente

Teledyne

Teledyne T3AFG30 Manuale utente

Teledyne

Teledyne HDO9000 Manuale utente

Teledyne

Teledyne T3HVD Manuale utente

Teledyne

Teledyne Reson PDS Scheda tecnica

Teledyne

Teledyne LabMaster 10 Zi Series Manuale utente

Teledyne

Teledyne USB-PD TDMP Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente