Teledyne T3DSO2000 Manuale utente

User Manual

T3DSO2000 Series Digital Oscilloscope

www. .com information@itm.com1.800.561.8187

Trademark Information

Teledyne Test Tools is the registered trademark of Teledyne LeCroy.

Declaration

Teledyne LeCroy products are protected by patent law.

Teledyne LeCroy reserves the right to modify or change parts of or all the specifications

or pricing policies at company‘s sole decision.

Information in this publication replaces all previously corresponding material.

Any way of copying, extracting or translating the contents of this manual is not allowed

without the permission of Teledyne LeCroy.

Product Certification

Teledyne Test Tools guarantees this product conforms to the national and industrial

standards and other international standards.

www. .com information@itm.com1.800.561.8187

Safety Information

General Safety Summary

Carefully read the following safety precautions to avoid any personal injury or

damage to the instrument and any products connected to it. To avoid potential

hazards, please use the instrument as specified.

Use Proper Power Cord

Only the power cord designed for the instrument and authorized by local country should

be used.

Ground the Instrument

The instrument is grounded through the protective earth conductor of the power cord. To

avoid electric shock, please make sure the instrument is grounded correctly before

connecting its input or output terminals.

Connect the Signal Wire Correctly

The potential of the signal wire ground is equal to the earth, so do not connect the signal

wire to a high voltage.

Look Over All Terminals‟ Ratings

To avoid fire or electric shock, please look over all ratings and sign instruction of the

instrument. Before connecting the instrument, please read the manual carefully to gain

more information about the ratings.

Use Proper Over-voltage Protection

Make sure that no over-voltage (such as that caused by a thunderstorm) can reach the

Product, to avoid exposure to the danger of electrical shock.

Electrostatic Prevention

Operate in an electrostatic discharge protective area environment to avoid damages

induced by static discharge. Always ground both the internal and external conductors of

the cable to release static before connecting.

Maintain Proper Ventilation

Inadequate ventilation may cause an increase of instrument‘s temperature, which may

eventually damage the instrument. Maintain proper ventilation and inspect the intake and

fan regularly.

www. .com information@itm.com1.800.561.8187

III

Avoid Exposed Circuits and Components

Do not touch exposed contacts or components when the power is on.

Use the Proper Fuse

Use only the specified fuse.

Do Not Operate Without Covers

Do not operate the instrument with covers or panels removed.

Do Not Operate With Suspected Failures.

If you suspect damage has occurred to the instrument, have it inspected by qualified

service personnel before further operation. Any maintenance, adjustment or replacement

especially to circuits or accessories must be performed by Teledyne Test Tools authorized

personnel.

Do Not Operate in Wet Conditions.

In order to avoid short circuiting to the interior of the device or electric shock, please do

not operate in a humid environment.

Do Not Operate in an Explosive Atmosphere.

In order to avoid damage to the device or personal injury, it is important to operate the

device away from an explosive atmosphere.

Keep Product Surfaces Clean and Dry.

To avoid the influence of dust and/or moisture in air, please keep the surface of device

clean and dry.

Handling Safety

Please handle with care during transportation to avoid damage to buttons, knobs, screen,

connectors and other parts.

www. .com information@itm.com1.800.561.8187

Safety Terms and Symbols

Terms in this Manual. These terms may appear in this manual:

Terms and Symbols

The following symbols appear on the product or in its documentation:

WARNING High Voltage. Risk of electric shock or burn.

WARNING or CAUTION Condition or practice could result in injury or

loss of life, or damage to equipment.

PROTECTIVE (EARTH) TERMINAL

Rated for indoor use only. Do not operate where conductive pollutants

may be present.

This electronic product is subject to disposal and recycling regulations

that vary by country and region. Many countries prohibit the disposal

of waste electronic equipment in standard waste receptacles. For more

information about proper disposal and recycling of your Teledyne

LeCroy product,

www. .com information@itm.com1.800.561.8187

Measurement Category

Measurement Categories

T3DSO2000 series digital oscilloscope’s measurement terminals are not rated for

measurements within measurement categories II, III, or IV

WARNING

Measuring terminals on this product are not intended to be connected directly

to mains.

Measurement Category Definitions

Measurement category II is for measurements performed on circuits directly connected to

low voltage installations. Examples are measurements on household appliances, portable

tools and similar equipment.

Measurement category III is for measurements performed in the building installation.

Examples are measurements on distribution boards, circuit-breakers, wiring, including

cables, bus-bars, junction boxes, switches, socket-outlets in the fixed installation, and

equipment for industrial use and some other equipment, for example. Stationary motors

with permanent connection to the fixed installation.

Measurement category IV is for measurements performed at the source of the low-voltage

installation. Examples are electricity meters and measurements on primary over current

protection devices and ripple control units.

www. .com information@itm.com1.800.561.8187

Working Environment

Temperature

Operating: 10℃ to +40℃

Non-operation:-20℃ to +60℃

Humidity

Operating: 85% RH, 40℃, 24 hours

Non-operating: 85% RH, 65℃, 24 hours

WARNING

To avoid short circuit inside the instrument or electric shock, please do not

operate in humid environment.

Altitude

Operating: less than 3 km

Non-operation: less than 15 km

Installation (Over Voltage) Category

This product is powered by mains conforming to installation (over-voltage) category II.

WARNING

Make sure that no over-voltage (such as that caused by lightning) can reach

the product or else the operator might be exposed to danger of electric shock.

Installation (Over-voltage) Category Definitions

Installation (over-voltage) category II refers to the local power distribution level which is

applicable to equipment connected to the AC line (AC power).

www. .com information@itm.com1.800.561.8187

VII

Ventilation Requirement

This oscilloscope uses fan-forced air cooling. Please make sure that the air intake and

exhaust areas are free from obstructions and have adequate ventilation. When using the

oscilloscope in a bench-top or rack setting, provide at least 10 cm clearance beside,

above and behind the instrument for adequate ventilation.

WARNING

Inadequate ventilation may cause temperature increase which would damage

the instrument. So please keep the instrument well ventilated during

operation and inspect the intake and fan regularly.

www. .com information@itm.com1.800.561.8187

VIII

General Care and Cleaning

Care

Do not store or leave the instrument in direct sunshine for long periods of time.

WARNING

To avoid damage to the instrument or probes, please do not leave them in fog,

liquid, or solvents.

Cleaning

Please perform the following steps to clean the instrument and probe regularly according

to its operating conditions.

1. Disconnect the instrument from all power sources and then clean it with a soft wet

cloth.

2. Clean the loose dust on the outside of the instrument and probe with a soft cloth.

When cleaning the LCD, take care to avoid scratching it.

WARNING

To avoid damage to the surface of the instrument and probe, please do not

use any corrosive liquid or chemical cleanser.

WARNING

Make sure that the instrument is completely dry before restarting it to avoid

short circuits or personal injury.

www. .com information@itm.com1.800.561.8187

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Teledyne Apparecchiature di prova

Teledyne

Teledyne T3EL15030 P Series Manuale utente

Teledyne

Teledyne HDO9000 Manuale utente

Teledyne

Teledyne waverunner xi-a series Manuale elenco delle parti

Teledyne

Teledyne HDO6000B Manuale utente

Teledyne

Teledyne USB-PD TDMP Manuale utente

Teledyne

Teledyne LabMaster 10 Zi Series Manuale elenco delle parti

Teledyne

Teledyne HDO4000 Manuale utente

Teledyne

Teledyne Everywhereyoulook T3DSOH1000 Manuale utente

Teledyne

Teledyne HPM 4 Manuale utente

Teledyne

Teledyne GT Series Guida rapida

Teledyne

Teledyne Reson PDS Scheda tecnica

Teledyne

Teledyne LabMaster 10 Zi Series Manuale utente

Teledyne

Teledyne T3AFG30 Manuale utente

Teledyne

Teledyne T3HVD Manuale utente

Teledyne

Teledyne T700 Manuale utente

Teledyne

Teledyne LeCroy Waverunner LT Series Foglio di istruzioni

Teledyne

Teledyne T3DSO1000 Manuale utente

Teledyne

Teledyne T3CP100-2 Manuale utente

Teledyne

Teledyne FST-040 Manuale utente

Teledyne

Teledyne HDO8000A Manuale utente

Teledyne

Teledyne 804A Manuale utente

Teledyne

Teledyne LeCroy T3DSO2000A Series Manuale utente

Teledyne

Teledyne ZD200 Manuale elenco delle parti

Teledyne

Teledyne T700 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente