TESTO 810 Come usare

Short manual testo 810 13

Short manual testo 810

Protection cap: Park position

Infrared sensor

Air/temperature sensor

Display

Control keys

Battery compartment (on rear)

Basic settings

Instrument off >press and hold 2s > select with ( ),

confirm with ( ):

Unit of temperature: °C,°F > Differential temperature t:OFF,ON >

Emissonsfaktor: > Auto off-Funktion: OFF,ON

Switching the instrument on

Press .

Switching the display light on (for 10s)

Instrument on > press .

IR measurements

Press and hold .

Select display mode

Instrument on > select with :

Hold: Readings are held > Max: Maximum values > Min: Minimum values

Switching the instrument off:

Instrument on >press and hold 2s.

Safety and the enviroment14

Safety and the environment

About this document

Please read this documentation through carefully and

familiarise yourself with the product before putting it to use.

Keep this document to hand so that you can refer to it when

necessary. Hand this documentation on to any subsequent

users of the product.

Pay particular attention to information emphasised by the

following symbols:

Important.

Avoid personal injury/damage to equipment

Only operate the measuring instrument properly, for its

intended purpose and within the parameters specified in the

technical data. Do not use force.

Never store the product together with solvents, acids or other

aggressive substances.

Only carry out the maintenance and repair work that is

described in the documentation. Follow the prescribed steps

when doing so. Use only OEM spare parts from Testo.

Protecting the environment

Take faulty rechargeable batteries as well as spent batteries to

the collection points provided for them.

Send the product back to Testo at the end of its useful life. We

will ensure that it is disposed of in an environmentally friendly

manner.

Specifications 15

Specifications

Functions and use

The testo 810 is an infrared measuring instrument. It is normally

used to measure surface temperature, e.g. on heaters and

radiators, and to measure the ambient temperature at the same

time.

Technical data

Measurement data

· Sensors:

Infrared sensor,

NTC temperature sensor

· Parameters:

°C, °F

· Measuring ranges:

IR: -30...300 °C, -20...575 °F,

Air probe: -10...50 °C, 14...122 °F

· Resolutions:

0.1 °C, 0.1 °F,

· Accuracies

(Nenntemperatur 22 °C, ±1 Digit):

Infrared: ±2 °C (-30...+100 °C),

±3.6 °F (-22...212 °C),

±2 % of reading (rest of range)

Air probe: ±0.5 °C, ±0.9 °F

· Measuring rate:

0.5 s

· Optics:

6 : 1

Further instrument data

· Protection class: IP40

· Ambient conditions:

-10...50 °C, 14...122 °F

· Storage/transport conditions:

-40...70 °C, -40...158 °F

· Voltage supply:

2x 1.5 V type AAA

· Battery life:

50 h (without display light)

· Dimensions:

119x46x25 mm (inc. protection cap)

· Weight: 90 g (inc. batteries and

protection cap)

Directives, standards and tests

· EC Directive: 89/336/EEC

Warranty

· Duration: 2 years

· Warranty conditions: see guarantee

card

Product description16

Product description

At a glance

Protection cap: Park position

Infrared sensor

Air/temperature sensor

Display

Control keys

Battery compartment (on rear)

First steps

Inserting batteries:

1To open the battery compartment, push the battery cover

down.

2Insert batteries (2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

Basic settings (configuration mode):

Adjustable functions

· Unit of temperature: °C,°F

· Differential temperature t:OFF,ON

· Emission factor:

· Auto off function: OFF,ON (instrument switches off automatically if no key is

pressed for 10 minutes)

The emission factor has a default setting of 0.95. This is

ideal for the measurement of non-metals (paper, ceramic,

gypsum, wood, paints and varnishes), plastics and

foodstuffs.

Product description 17

Because of their low or non-uniform emission factor, bright

metals and metal oxides are of only limited use for infrared

measurement. Coatings that increase the emission factor,

e.g. paint or emission adhesive (0554 0051) must be

applied to the object being measured.

Emission factors of various materials (typical values):

Material (temperature)

Aluminium, bright rolled (170 °C) 0.04

Cotton (20 °C) 0.77

Concrete (25 °C) 0.93

Ice, smooth (0 °C) 0.97

Iron, emery ground (20 °C) 0.24

Iron with casting skin (100 °C) 0.80

Iron with rolling skin (20 °C) 0.77

Gypsum (20 °C) 0.90

Glass (90 °C) 0.94

Rubber, hard (23 °C) 0.94

Rubber, soft grey (23 °C) 0.89

Wood (70 °C) 0.94

Cork (20 °C) 0.70

Radiator, black anodised (50 °C) 0.98

Copper, slightly tarnished (20 °C) 0.04

Copper, oxidised (130 °C) 0.76

Plastics: PE, PP, PVC (20 °C) 0.94

Brass, oxidised (200 °C) 0.61

Paper (20 °C) 0.97

Porcelain (20 °C) 0.92

Black paint, matt (80 °C) 0.97

Steel, heat-treated surface (200 °C) 0.52

Steel, oxidised (200 °C) 0.79

Clay, burnt (70 °C) 0.91

Transformer paint (70 °C) 0.94

Brick, mortar, plaster (20 °C) 0.93

1When switching the instrument on, press and hold until

and appear on the display (configuration mode).

- The adjustable function is displayed. The current setting

flashes.

2Press ( ) several times until the desired setting flashes.

3Press ( ) to confirm the input.

4Repeat steps 2and 3for all functions.

- The instrument changes to measuring mode.

Using the product18

Using the product

Switching the instrument on:

Press .

- Measuring mode is opened.

Switching the display light on:

The instrument is switched on.

Press .

- The display light goes out automatically if no key is

pressed for 10 seconds.

IR measurements:

Laser radiation! Do not look into the laser beam.

Laser class 2.

To ensure correct readings:

· Keep temperature and humidity sources which may falsify the

measurement (e.g. hands) away from the sensor.

· Keep the lens clean and do not measure with foggy lenses.

· Keep the measuring range (the range between the instrument and the

object being measured) and the surface of the object free of obstacles.

There must be no particles of dust or dirt, no humidity (rain, steam) and

no gases.

· If the ambient temperature changes (change of location, e.g.

measurement indoors/outdoors), the instrument must be allowed to

equalise for aprox. 15 minutes.

· The instrument has a lens (90 % value) of 6:1 (distance : measuring

surface) + Opening diameter of the sensor (10mm / 0.39 in):

Distance Diameter of meas. surface Distance Diameter of meas. surface

10cm 3cm 4in 1.06in

60cm 11cm 25in 4.56in

100cm 18cm 40in 7.06in

200cm 35cm 80in 13.72in

Press and hold .

- flashes in the display. The laser dot marks the centre

of the measuring surface.

-

the

readings are held.

Using the product 19

Changing the display view:

Adjustable views

·Hold: Readings are held.

·Max: Maximum values since the instrument was last switched on or last reset.

·Min: Minimum values since the instrument was last switched on or last reset.

Press several times until the desired view appears.

Resetting Max/Min values:

1Press several times until the desired view appears.

2Press and hold until ---- appears.

3Repeat steps 1and 2for all values that are to be reset.

Switching the instrument off:

Press and hold until the display goes out.

Maintaining the product20

Maintaining the product

Changing batteries:

1To open the battery compartment, push the battery cover

down.

2Remove used batteries and insert new batteries

(2x 1.5 V type AAA). Observe the polarity!

3To close the battery compartment, push the battery cover

back on.

Cleaning the housing:

Clean the housing with a moist cloth (soap suds) if it is dirty.

Do not use aggressive cleaning agents or solvents!

Tips and assistance 21

Tips and assistance

Questions and answers

Question Possible causes/solutions

Hi or Lo · Readings outside the measuring range (too high, too

low): Keep to the permitted measuring range.

· Residual capacity <10 min: Change batteries.

If we could not answer your question, please contact your dealer

or Testo Customer Service. Contact details can be found on the

guarantee card or on the Internet at: www.testo.com

Notes22

Altri manuali per 810

3

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente