Texas Instruments TPS40200 Manuale utente

User's GuideSLVU147A – February 2006 – Revised March 2006

Using the TPS40200

The TPS40200EVM-001 evaluation module (EVM) uses the TPS40200nonsynchronous buck converter to provide a resistor-selected 3.3-V output voltage thatdelivers up to 2.5 A from a 12-V input bus. The EVM operates from a single supply anduses a single P-channel power FET and Schottky diode to produce a low-cost buckconverter. The part operates at a 300-kHz clock frequency with provision for externalfrequency synchronization.

Contents1 Description ........................................................................................... 22 TPS40200EVM-001 Electrical and Performance Specifications ............................. 23 Schematic ........................................................................................... 34 Test Setup ........................................................................................... 45 TPS40200EVM Typical Performance Data and Characteristic Curves ..................... 76 EVM Assembly Drawings and Layout ........................................................... 97 List of Materials .................................................................................... 14

List of Figures

1 TPS40200EVM-001 Schematic ................................................................... 32 TPS40200 Synchronized to a 50% Duty Cycle External Clock .............................. 43 TPS40200EVM-001 Recommended Test Setup ............................................... 64 Output Ripple Measurement - Tip and Barrel Using TP14 and TP15 ....................... 65 TPS40200EVM-001 Efficiency .................................................................... 76 TPS40200EVM-001 Efficiency .................................................................... 87 TPS40200EVM-001 Line and Load Regulation – Vout = 3.3255 V .......................... 88 TPS40200EVM-001 Line and Load Regulation – Vout = 5.0665 V ......................... 99 TPS40200EVM-001 Component Placement (Viewed from Top) ........................... 1010 TPS40200EVM-001 Silkscreen (Viewed from Top) .......................................... 1111 TPS40200EVM-001 Top View .................................................................. 1212 TPS40200EVM-001 Bottom View ............................................................... 13

List of Tables

1 Adjusting V

OUT

With R6 Rounded to Standard 1% Resistor Values ......................... 32 TPS40200EVM-001 Bill of Materials ........................................................... 14

SLVU147A – February 2006 – Revised March 2006 Using the TPS40200 1Submit Documentation Feedback

www.ti.com

1 Description

1.1 Features

1.2 Applications

2 TPS40200EVM-001 Electrical and Performance Specifications

Description

TPS40200EVM-001 is designed to operate with an 8-V to 16-V input and to produce a regulated 3.3-Voutput with a load current from 0.125 A to 2.5 A. The TPS40200EVM-001 demonstrates the use of theTPS40200 in a typical buck converter application. The board sacrifices some packing density to provideample test points for module evaluation. This EVM can be modified to support output voltages from 0.7 Vto 5 V by changing a single feedback resistor. The TPS40200EVM-001 has been built to the sampleapplication as described in the Application Information section of the TPS40200 data sheet (SLUS659 ).

•8-V to 16-V input range•3.3-V output, adjustable with single feedback resistor•0.125-A to 2.5-A steady-state output current•300-kHz switching frequency•Single P-channel MOSFET and single rectifier•Two-layer, 1.4-inch ×2.12-inch, surface-mount design with all components on one side•Convenient test points for probing critical waveforms and noninvasive loop response testing

•Nonisolated medium-current, point-of-load and low-voltage bus converters•Scanners

•Industrial controls•Distributed power systems•DSL/cable modems

PARAMETER TEXT CONDITIONS MIN NOM MAX UNIT

Input voltage 8 12 16 VV

OUT

Output voltage IOUT at 2.5 A, R6 = 26.7 k Ω3.200 3.3 3.400

(1)

VLine regulation ±0.2% Vout 3.293 3.3 3.307 VLoad regulation ±0.2% Vout 3.293 3.3 3.307 VV

OUT

Output voltage IOUT at 2.5 A, R6 = 16.5 k Ω4.85 5 5.150

(1)

VLine regulation ±0.2% Vout 4.990 5 5.010 VLoad regulation ±0.2% Vout 4.990 5 5.010 VV

RIPPLE

Output ripple voltage At maximum output current 60 mVV

OVER

Output overshoot For 2.375-A load transient 60 mVV

UNDER

Output undershoot For 2.375-A load transient 60 mVI

OUT

Output current 0.125 2.5 AI

SCP

Short-circuit current trip point Imax +50% minimum 3.75 5 AEfficiency At nominal input voltage and maximum output 90%currentF

Switching frequency 300 kHz

(1)

Set-point accuracy depends on external resistor tolerance and the reference voltage. Line and load regulation values arereferenced to the nominal design output voltage.

Using the TPS402002 SLVU147A – February 2006 – Revised March 2006Submit Documentation Feedback

www.ti.com

3 Schematic

Notes

R6 =26.7k for 3.3 Vout, R6 = 16.2k for 5.0 Vout

D3 : Do not populate. SOT 23 Common Cathode Dual Schottky

3.1 Adjusting Output Voltage (R6 and R10)

Vvout Vref1R10

R6

(1)

3.2 Using Remote Synchronizing (TP6)

Schematic

NOTE: For reference only; see Table 2, Bill of Materials for specific values

Figure 1. TPS40200EVM-001 Schematic

The regulated output voltage can be adjusted within a limited range by changing the ground resistor in thefeedback resistor divider (R6 and R10). The output voltage is given by Equation 1 .

Where V

REF

= 0.700 V and R10 = 100 k Ω

Table 1 contains common values for R6 to generate popular output voltages. TPS40200EVM-001 is stablethrough these output voltages with the efficiency rising with output voltage.

Table 1. Adjusting V

OUT

With R6 Rounded toStandard 1% Resistor Values

OUT

- Output Voltage (V) R6 - Feedback Resistor Divider(k Ω)

5 16.23.3 26.72.5 392 53.61.8 63.41.5 86.61.2 140

The TPS40200EVM-001 board has a synchronizing circuit that uses TP6 as an input. A logic high at thisinput turns on a small signal FET (Q1) whose drain is connected to the oscillator setting node (RC) on theTPS40200. The switching of this transistor over-drives the ramp associated with the internal oscillator andcauses the PWM switching to follow the input clock frequency. For reliable operation, the external clock

SLVU147A – February 2006 – Revised March 2006 Using the TPS40200 3Submit Documentation Feedback

www.ti.com

4 Test Setup

4.1 Equipment

Test Setup

frequency should be 25% to 30% higher than the frequency set by R3 and C5. The BSS83 used in thiscircuit has a low (1-pF) output capacitance; so, its presence does not load down the normal operation ofthe RC pin. With the controller’s frequency set to a 300-kHz frequency, the module synchronizes to a390-kHz external clock that has a 50% duty cycle. A shorting jack, J2, is provided to disconnect thesynchronizing circuit from the (RC) node.

The following scope picture (Figure 2 ) shows a 5-V input clock at the TP6 input operating at 390 kHz anda 50% duty cycle. The switch node also shown in the picture is switching at the same frequency with a12-V V

supply. The RC operating frequency of the TPS40200 is set by R3 and C5 to be 300 kHz.

Figure 2. TPS40200 Synchronized to a 50% Duty Cycle External Clock

4.1.1 Voltage Source

12V_IN

— The input voltage source (V

12V_IN

) should be a 0-V to 20-V variable dc source capable of 5 A dc.

METERS

A1: 0-A to 5-A dc ammeterV1: V

12V_IN

, 0-V to 20-V voltmeterV2: V

3V3_OUT

0 V to 10-V voltmeter

4.1.2 Loads

LOAD1 — The output load (LOAD1) should be an electronic constant-current-mode load capable of 0A-to-2.5 A dc at 1.5 V.

4.1.3 Recommended Wire Gauge

12V_IN

to J1 — The connection between the source voltage, V

12V_IN

and J1 of HPA164 can carry as muchas 3 A dc. The minimum recommended wire size is AWG 16 with the length of wire less than 4 feet (2 feetinput, 2 feet return).

4Using the TPS40200 SLVU147A – February 2006 – Revised March 2006Submit Documentation Feedback

www.ti.com

4.2 Equipment Setup

Test Setup

J3 to LOAD1 (Power) — The power connection between J3 of HPA164 and LOAD1 can carry as much as5 A dc. The minimum recommended wire size is 2x AWG 16, with the length of wire less than 4 feet (2feet output, 2 feet return).

J3 to LOAD1 (Remote Sense) — If remote sense is used, the remote sense connection between J3 ofHPA164 and LOAD1 will carry less than 1 A dc. The minimum recommended wire size is AWG 22, withthe length of wire less and 4 feet (2 feet output, 2 feet return).

4.1.4 Oscilloscope

A 60-MHz or faster oscilloscope can be used to determine the ripple voltage on 3V3_OUT. Theoscilloscope should be set for 1-M Ωimpedance, ac coupling, 1- µs/division horizontal resolution,20-mV/division vertical resolution for taking output ripple measurements. TP14 and TP15 can be used tomeasure the output ripple voltage by placing the oscilloscope probe tip through TP14 and holding theground barrel to TP15 as shown in Figure 3 . For a hands-free approach, the loop in TP15 can be cut andopened to cradle the probe barrel. Using a leaded ground connection may induce additional noise due tothe large ground loop area. Connect a short wire from the barrel of the scope probe to TP15 as necessaryto reach between TP14 and TP15.

Shown in Figure 3 is the basic test setup recommended to evaluate the TPS40200EVM-001. Note thatalthough the return for J1 and J3 are the same, the connections should remain separate as shown inFigure 3 .

4.2.1 Procedure

1. Working at an ESD workstation, ensure that any wrist straps, bootstraps, or mats are connectedreferencing the user to earth ground before power is applied to the EVM. Electrostatic smock andsafety glasses should also be worn.2. Prior to connecting the dc-input source, V

12V_IN

, it is advisable to limit the source current from V

12V_IN

to5 A maximum. Ensure that V

12V_IN

is initially set to 0 V and connected as shown in Figure 2 .3. Connect the ammeter A1 (0-A to 5-A range) between V

12V_IN

and J1 as shown in Figure 3 .4. Connect voltmeter V1 to TP1 and TP3 as shown in Figure 3 .5. Connect LOAD1 to J3 as shown in Figure 1 . Set LOAD1 to constant current mode to sink 0 A dcbefore V

12V_IN

is applied.6. Connect voltmeter, V2 across J3 pin 3 and J3 pin 2 as shown in Figure 3 .7. Connect the oscilloscope probe to TP14 and TP15 as shown in Figure 4 .

SLVU147A – February 2006 – Revised March 2006 Using the TPS40200 5Submit Documentation Feedback

www.ti.com

LOAD1

3.3V @

2.5A

−+

−3V3_OUT +

+12V_IN −

+−

Oscilloscope

1M ,AC

20mV / div

20MHz

−

12V_IN

TP1

TP3 TP 14

TP6

TEXAS INSTRUMENTS

TPS40200EVM−001

12V to 3.3V @ 2.5A with sync Input

HPA164

−

Sync

See Tip and Barrel

Measurement for V out

ripple

Short

for

Sync

−

TP1

−++

TP1

TP 15

−

TP15TP14

Metal Ground Barrel

Probe Tip

Tip and Barrel Vout ripple measurement

4.3 Startup/Shutdown Procedure

Test Setup

4.2.2 Diagram

Figure 3. TPS40200EVM-001 Recommended Test Setup

Figure 4. Output Ripple Measurement - Tip and Barrel Using TP14 and TP15

1. Increase V

12V_IN

(V1) from 0 V to 12 V dc.2. Vary LOAD1 from 0 A to 2.5 A dc.3. Vary V

12V_IN

(V1) from 8 Vdc to 16 V dc.4. Decrease LOAD1 to 0 A.5. Decrease V12V_IN to 0 V.

Using the TPS402006 SLVU147A – February 2006 – Revised March 2006Submit Documentation Feedback

www.ti.com

4.4 Equipment Shutdown

5 TPS40200EVM Typical Performance Data and Characteristic Curves

5.1 Efficiency

100

00.5 11.5 22.5 3

VI= 8 V

VI= 12 V VI= 16 V

VO= 3.3 V

−Efficiency −%

IO−Load Current −A

TPS40200EVM Typical Performance Data and Characteristic Curves

1. Shut down oscilloscope.2. Shut down LOAD1.3. Shut down V

12V_IN

Figure 5 through Figure 8 present typical performance curves for the TPS40200EVM-001. Because actualperformance data can be affected by measurement techniques and environmental variables, these curvesare presented for reference and may differ from actual field measurements.

NOTE: V

12V_IN

= 8-, 12-, and 16-V, V

3V3_OUT

= 3.3 V, I

1V5_OUT

= 0.125 A to 2.5 A

Figure 5. TPS40200EVM-001 Efficiency

SLVU147A – February 2006 – Revised March 2006 Using the TPS40200 7Submit Documentation Feedback

www.ti.com

100

00.5 11.5 22.5 3

VI= 8 V

VO= 5 V

−Efficiency −%

IO−Load Current −A

VI= 12 V VI= 16 V

5.2 Line and Load Regulation

3.322

3.323

3.324

3.325

3.326

3.327

3.328

3.329

3.33

3.331

00.5 11.5 22.5 3

VI= 8 V

IO− Load Current − A

VI= 12 V

VI= 16 V

− Output Voltage − V

VO= 3.3255 V

TPS40200EVM Typical Performance Data and Characteristic Curves

NOTE: V

12V_IN

= 8-, 12-, and 16-V, V

3V3_OUT

= 5 V, I

1V5_OUT

= 0.125 A to 2.5 A

Figure 6. TPS40200EVM-001 Efficiency

Figure 7. TPS40200EVM-001 Line and Load Regulation – Vout = 3.3255 V

8Using the TPS40200 SLVU147A – February 2006 – Revised March 2006Submit Documentation Feedback

www.ti.com

5.062

5.064

5.066

5.068

5.07

5.072

5.074

5.076

0 0.5 1 1.5 2 2.5 3

VI= 8 V

IO− Load Current − A

VI= 12 V

VI= 16 V

− Output Voltage − V

6 EVM Assembly Drawings and Layout

EVM Assembly Drawings and Layout

Figure 8. TPS40200EVM-001 Line and Load Regulation – Vout = 5.0665 V

The following figures (Figure 9 through Figure 12 ) show the design of the TPS40200EVM-001printed-circuit board. The EVM has been designed using a 2-layer, 2-oz copper-clad circuit board, 1.4-inch×2.12-inch in size, with all components on the top side to allow the user to easily view, probe, andevaluate the TPS40200 control IC in a practical application. Moving components to both sides of the PCBor using additional internal layers can offer additional size reduction for space-constrained systems.

SLVU147A – February 2006 – Revised March 2006 Using the TPS40200 9Submit Documentation Feedback

www.ti.com

EVM Assembly Drawings and Layout

Figure 9. TPS40200EVM-001 Component Placement (Viewed from Top)

10 Using the TPS40200 SLVU147A – February 2006 – Revised March 2006Submit Documentation Feedback

Indice

Altri manuali Texas Instruments Unità di controllo

Texas Instruments

Texas Instruments TRF7960A Manuale utente

Texas Instruments

Texas Instruments TPS53313 Manuale utente

Texas Instruments

Texas Instruments BQ25181 Manuale utente

Texas Instruments

Texas Instruments CDCM1804 Manuale utente

Texas Instruments

Texas Instruments TPS2559EVM-624 Manuale utente

Texas Instruments

Texas Instruments LM5122EVM-2PH Manuale utente

Texas Instruments

Texas Instruments bq25505 Manuale utente

Texas Instruments

Texas Instruments TAS5782M Manuale utente

Texas Instruments

Texas Instruments TPS54980EVM-022 Manuale utente

Texas Instruments

Texas Instruments bq24072 Manuale utente

Texas Instruments

Texas Instruments MCF8316AEVM Manuale utente

Texas Instruments

Texas Instruments ADC1173 Manuale utente

Texas Instruments

Texas Instruments TRF7970A BoosterPack Manuale utente

Texas Instruments

Texas Instruments ADS8353-Q1 Manuale utente

Texas Instruments

Texas Instruments AFE79 Series Istruzioni per il montaggio

Texas Instruments

Texas Instruments AWR1443 Manuale utente

Texas Instruments

Texas Instruments TPS54226EVM-539 Manuale utente

Texas Instruments

Texas Instruments bq24153A Manuale utente

Texas Instruments

Texas Instruments TA 5 1 Q15B5EVM-K Series Manuale utente

Texas Instruments

Texas Instruments DRV8601 Manuale utente

Texas Instruments

Texas Instruments LM74700DDFEVM Manuale utente

Texas Instruments

Texas Instruments UCC27423-Q1 Manuale utente

Texas Instruments

Texas Instruments MCT8316AEVM Manuale utente

Texas Instruments

Texas Instruments LM5164-Q1 EVM Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente